mirror of
https://git.FreeBSD.org/src.git
synced 2024-12-20 11:11:24 +00:00
be4aa869c1
14.00.00.01-fbsd. Their description of the changes is as follows: 1. Copyright contents has been changed in all respective .c and .h files 2. Support for WRITE12 and READ12 for direct-io (warpdrive only) has been added. 3. Driver has added checks to see if Drive has READ_CAP_16 support before sending it down to the device. If SPC3_SID_PROTECT flag is set in the inquiry data, the device supports protection information, and must support the 16 byte read capacity command, otherwise continue without sending read cap 16. This will optimize driver performance, since it will not send READ_CAP_16 to the drive which does not have support of READ_CAP_16. 4. With new approach, "MPTIOCTL_RESET_ADAPTER" IOCTL will not use DELAY() which is busy loop implementation. It will use <msleep> (Better way to sleep without busy loop). Also from the HBA reset code path and some other places, DELAY() is replaced with msleep() or "pause()", which is based on sleep/wakeup style calls. Driver use msleep()/pause() instead of DELAY based on CAN_SLEEP/NO_SLEEP flags to avoid busy loop which is not required all the time.e.a a. While driver is getting loaded, driver calls most of the commands with NO_SLEEP. b. When Driver is functional and it needs Reinit of HBA, CAN_SLEEP flag is used. 5. <mpslsi> driver is not Endian safe. It will not work on Big Endian machines like Sparc and PowerPC platforms because it assumes it is running on a Little Endian machine. Driver code is modified such way that it does not assume CPU arch is Little Endian. a. All places where Driver interacts from HBA to Host, it converts Little Endian format to CPU format. b. All places where Driver interacts from Host to HBA, it converts CPU format to Little Endian. 6. Findout memory leaks in FreeBSD Driver and resolve those, such as memory leak in targ's luns creation/deletion. Also added additional checks to see memory allocation success/fail. 7. Add loginfo prints as debug message, i.e. When FW sends any loginfo, Driver should print those as debug message. This will help for debugging purpose. 8. There is possibility to get config request timeout. Current driver is able to detect config request timetout, but it does not do anything on config_request timeout. Driver should call mps_reinit() if any request_poll (which is called as part of config_request) is time out. 9. cdb length check is required for 32 byte CDB. Add correct mpi control value for 32 bit CDB as below while submitting SCSI IO Request to controller. mpi_control |= 4 << MPI2_SCSIIO_CONTROL_ADDCDBLEN_SHIFT; 10. Check the actual status of Message unit reset (mps_message_unit_reset).Previously FreeBSD Driver just writes MPI2_FUNCTION_IOC_MESSAGE_UNIT_RESET and never check the ack (it just wait for 50 millisecond). So, Driver now check the status of "MPI2_FUNCTION_IOC_MESSAGE_UNIT_RESET" after writing it to the FW. Now it also checking for whether doorbell ack uses msleep with proper sleep flags, instead of <DELAY>. 11. Previously CAM does not detect Multi-Lun Devices. In order to detect Multi-Lun Devices by CAM the driver needs following change set: a. There is "max_lun" field which Driver need to set based on hw/fw support. Currently LSI released driver does not set this field. b. Default of "max_lun" should not be 0 in OS, but it is currently set to 0 in CAM layer. c. Export max_lun capacity to 255 12. Driver will not reset target info after port enable complete and also do Device removal when Device remove from FW. The detail description is as follows a. When Driver receive WD PD add events, it will add all information in driver local data structure. b. Only for WD, we have below checks after port enable completes, where driver clear off all information retrieved at #1. if ((sc->WD_available && (sc->WD_hide_expose == MPS_WD_HIDE_ALWAYS)) || (sc->WD_valid_config && (sc->WD_hide_expose == MPS_WD_HIDE_IF_VOLUME)) { // clear off target data structure. } It is mainly not to attach PDs to OS. FreeBSD does bus rescan as older Parallel scsi style. So Driver needs to handle which Drive is visible to OS. That is a reason we have to clear off targ information for PDs. Again, above logic was implemented long time ago. Similar concept we have for non-wd also. For that, LSI have introduced different logic to hide PDs. Eventually, because of above gap, when Phy goes offline, we observe below failure. That is what Driver is not doing complete removal of device with FW. (which was pointed by Scott) Apr 5 02:39:24 Freebsd7 kernel: mpslsi0: mpssas_prepare_remove Apr 5 02:39:24 Freebsd7 kernel: mpssas_prepare_remove 497 : invalid handle 0xe Now Driver will not reset target info after port enable complete and also will do Device removal when Device remove from FW. 13. Returning "CAM_SEL_TIMEOUT" instead of "CAM_TID_INVALID" error code on request to the Target IDs that have no devices conected at that moment. As if "CAM_TID_INVALID" error code is returned to the CAM Layaer then it results in a huge chain of errors in verbose kernel messages on boot and every hot-plug event. Submitted by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com> MFC after: 3 days
72 lines
2.5 KiB
C
72 lines
2.5 KiB
C
/*-
|
|
* Copyright (c) 2011, 2012 LSI Corp.
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*
|
|
* LSI MPT-Fusion Host Adapter FreeBSD
|
|
*
|
|
* $FreeBSD$
|
|
*/
|
|
|
|
#ifndef _MPS_MAPPING_H
|
|
#define _MPS_MAPPING_H
|
|
|
|
/**
|
|
* struct _map_phy_change - PHY entries recieved in Topology change list
|
|
* @physical_id: SAS address of the device attached with the associate PHY
|
|
* @device_info: bitfield provides detailed info about the device
|
|
* @dev_handle: device handle for the device pointed by this entry
|
|
* @slot: slot ID
|
|
* @is_processed: Flag to indicate whether this entry is processed or not
|
|
*/
|
|
struct _map_phy_change {
|
|
uint64_t physical_id;
|
|
uint32_t device_info;
|
|
uint16_t dev_handle;
|
|
uint16_t slot;
|
|
uint8_t reason;
|
|
uint8_t is_processed;
|
|
};
|
|
|
|
/**
|
|
* struct _map_topology_change - entries to be removed from mapping table
|
|
* @dpm_entry_num: index of this device in device persistent map table
|
|
* @dev_handle: device handle for the device pointed by this entry
|
|
*/
|
|
struct _map_topology_change {
|
|
uint16_t enc_handle;
|
|
uint16_t exp_handle;
|
|
uint8_t num_entries;
|
|
uint8_t start_phy_num;
|
|
uint8_t num_phys;
|
|
uint8_t exp_status;
|
|
struct _map_phy_change *phy_details;
|
|
};
|
|
|
|
|
|
extern int
|
|
mpssas_get_sas_address_for_sata_disk(struct mps_softc *ioc,
|
|
u64 *sas_address, u16 handle, u32 device_info);
|
|
|
|
#endif
|