mirror of
https://git.FreeBSD.org/src.git
synced 2024-12-24 11:29:10 +00:00
375 lines
14 KiB
C
375 lines
14 KiB
C
/*
|
|
* file: mss.h
|
|
*
|
|
* (C) 1997 Luigi Rizzo (luigi@iet.unipi.it)
|
|
*
|
|
* This file contains information and macro definitions for
|
|
* AD1848-compatible devices, used in the MSS/WSS compatible boards.
|
|
*
|
|
*/
|
|
|
|
/*
|
|
*
|
|
|
|
The codec part of the board is seen as a set of 4 registers mapped
|
|
at the base address for the board (default 0x534). Note that some
|
|
(early) boards implemented 4 additional registers 4 location before
|
|
(usually 0x530) to store configuration information. This is a source
|
|
of confusion in that one never knows what address to specify. The
|
|
(current) convention is to use the old address (0x530) in the kernel
|
|
configuration file and consider MSS registers start four location
|
|
ahead.
|
|
|
|
*
|
|
*/
|
|
|
|
/*
|
|
* The four visible registers of the MSS :
|
|
*
|
|
*/
|
|
|
|
#define MSS_INDEX (0 + 4)
|
|
#define MSS_IDXBUSY 0x80 /* readonly, set when busy */
|
|
#define MSS_MCE 0x40 /* the MCE bit. */
|
|
/*
|
|
* the MCE bit must be set whenever the current mode of the
|
|
* codec is changed; this in particular is true for the
|
|
* Data Format (I8, I28) and Interface Config(I9) registers.
|
|
* Only exception are CEN and PEN which can be changed on the fly.
|
|
* The DAC output is muted when MCE is set.
|
|
*/
|
|
#define MSS_TRD 0x20 /* Transfer request disable */
|
|
/*
|
|
* When TRD is set, DMA transfers cease when the INT bit in
|
|
* the MSS status reg is set. Must be cleared for automode
|
|
* DMA, set otherwise.
|
|
*/
|
|
#define MSS_IDXMASK 0x1f /* mask for indirect address */
|
|
|
|
#define MSS_IDATA (1 + 4)
|
|
/*
|
|
* data to be transferred to the indirect register addressed
|
|
* by index addr. During init and sw. powerdown, cannot be
|
|
* written to, and is always read as 0x80 (consistent with the
|
|
* busy flag).
|
|
*/
|
|
|
|
#define MSS_STATUS (2 + 4)
|
|
|
|
#define IS_CUL 0x80 /* capture upper/lower */
|
|
#define IS_CLR 0x40 /* capture left/right */
|
|
#define IS_CRDY 0x20 /* capture ready for programmed i/o */
|
|
#define IS_SER 0x10 /* sample error (overrun/underrun) */
|
|
#define IS_PUL 0x08 /* playback upper/lower */
|
|
#define IS_PLR 0x04 /* playback left/right */
|
|
#define IS_PRDY 0x02 /* playback ready for programmed i/o */
|
|
#define IS_INT 0x01 /* int status (1 = active) */
|
|
/*
|
|
* IS_INT is clreared by any write to the status register.
|
|
*/
|
|
#if 0
|
|
#define io_Polled_IO(d) ((d)->io_base+3+4)
|
|
/*
|
|
* this register is used in case of polled i/o
|
|
*/
|
|
#endif
|
|
|
|
/*
|
|
* The MSS has a set of 16 (or 32 depending on the model) indirect
|
|
* registers accessible through the data port by specifying the
|
|
* appropriate address in the address register.
|
|
*
|
|
* The 16 low registers are uniformly handled in AD1848/CS4248 compatible
|
|
* mode (often called MODE1). For the upper 16 registers there are
|
|
* some differences among different products, mainly Crystal uses them
|
|
* differently from OPTi.
|
|
*
|
|
*/
|
|
|
|
/*
|
|
* volume registers
|
|
*/
|
|
|
|
#define I6_MUTE 0x80
|
|
|
|
/*
|
|
* register I9 -- interface configuration.
|
|
*/
|
|
|
|
#define I9_PEN 0x01 /* playback enable */
|
|
#define I9_CEN 0x02 /* capture enable */
|
|
|
|
/*
|
|
* values used in bd_flags
|
|
*/
|
|
#define BD_F_MCE_BIT 0x0001
|
|
#define BD_F_IRQ_OK 0x0002
|
|
#define BD_F_TMR_RUN 0x0004
|
|
#define BD_F_MSS_OFFSET 0x0008 /* offset mss writes by -4 */
|
|
#define BD_F_DUPLEX 0x0010
|
|
|
|
/*
|
|
* sound/ad1848_mixer.h
|
|
*
|
|
* Definitions for the mixer of AD1848 and compatible codecs.
|
|
*
|
|
* Copyright by Hannu Savolainen 1994
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions are
|
|
* met: 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer. 2.
|
|
* Redistributions in binary form must reproduce the above copyright notice,
|
|
* this list of conditions and the following disclaimer in the documentation
|
|
* and/or other materials provided with the distribution.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND ANY
|
|
* EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
|
|
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
|
|
* DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
|
|
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
|
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
|
|
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*/
|
|
/*
|
|
* The AD1848 codec has generic input lines called Line, Aux1 and Aux2.
|
|
* Soundcard manufacturers have connected actual inputs (CD, synth, line,
|
|
* etc) to these inputs in different order. Therefore it's difficult
|
|
* to assign mixer channels to to these inputs correctly. The following
|
|
* contains two alternative mappings. The first one is for GUS MAX and
|
|
* the second is just a generic one (line1, line2 and line3).
|
|
* (Actually this is not a mapping but rather some kind of interleaving
|
|
* solution).
|
|
*/
|
|
|
|
#define MSS_REC_DEVICES \
|
|
(SOUND_MASK_LINE | SOUND_MASK_MIC | SOUND_MASK_CD|SOUND_MASK_IMIX)
|
|
|
|
|
|
/*
|
|
* Table of mixer registers. There is a default table for the
|
|
* AD1848/CS423x clones, and one for the OPTI931. As more MSS
|
|
* clones come out, there ought to be more tables.
|
|
*
|
|
* Fields in the table are : polarity, register, offset, bits
|
|
*
|
|
* The channel numbering used by individual soundcards is not fixed.
|
|
* Some cards have assigned different meanings for the AUX1, AUX2
|
|
* and LINE inputs. Some have different features...
|
|
*
|
|
* Following there is a macro ...MIXER_DEVICES which is a bitmap
|
|
* of all non-zero fields in the table.
|
|
* MODE1_MIXER_DEVICES is the basic mixer of the 1848 in mode 1
|
|
* registers I0..I15)
|
|
*
|
|
*/
|
|
|
|
mixer_ent mix_devices[32][2] = {
|
|
MIX_NONE(SOUND_MIXER_VOLUME),
|
|
MIX_NONE(SOUND_MIXER_BASS),
|
|
MIX_NONE(SOUND_MIXER_TREBLE),
|
|
MIX_ENT(SOUND_MIXER_SYNTH, 2, 1, 0, 5, 3, 1, 0, 5),
|
|
MIX_ENT(SOUND_MIXER_PCM, 6, 1, 0, 6, 7, 1, 0, 6),
|
|
MIX_ENT(SOUND_MIXER_SPEAKER, 26, 1, 0, 4, 0, 0, 0, 0),
|
|
MIX_ENT(SOUND_MIXER_LINE, 18, 1, 0, 5, 19, 1, 0, 5),
|
|
MIX_ENT(SOUND_MIXER_MIC, 0, 0, 5, 1, 1, 0, 5, 1),
|
|
MIX_ENT(SOUND_MIXER_CD, 4, 1, 0, 5, 5, 1, 0, 5),
|
|
MIX_ENT(SOUND_MIXER_IMIX, 13, 1, 2, 6, 0, 0, 0, 0),
|
|
MIX_NONE(SOUND_MIXER_ALTPCM),
|
|
MIX_NONE(SOUND_MIXER_RECLEV),
|
|
MIX_ENT(SOUND_MIXER_IGAIN, 0, 0, 0, 4, 1, 0, 0, 4),
|
|
MIX_NONE(SOUND_MIXER_OGAIN),
|
|
MIX_NONE(SOUND_MIXER_LINE1),
|
|
MIX_NONE(SOUND_MIXER_LINE2),
|
|
MIX_NONE(SOUND_MIXER_LINE3),
|
|
};
|
|
|
|
#define MODE2_MIXER_DEVICES \
|
|
(SOUND_MASK_SYNTH | SOUND_MASK_PCM | SOUND_MASK_SPEAKER | \
|
|
SOUND_MASK_LINE | SOUND_MASK_MIC | SOUND_MASK_CD | \
|
|
SOUND_MASK_IMIX | SOUND_MASK_IGAIN )
|
|
|
|
#define MODE1_MIXER_DEVICES \
|
|
(SOUND_MASK_SYNTH | SOUND_MASK_PCM | SOUND_MASK_MIC | \
|
|
SOUND_MASK_CD | SOUND_MASK_IMIX | SOUND_MASK_IGAIN )
|
|
|
|
|
|
/*
|
|
* entries for the opti931...
|
|
*/
|
|
|
|
mixer_ent opti931_devices[32][2] = { /* for the opti931 */
|
|
MIX_ENT(SOUND_MIXER_VOLUME, 22, 1, 1, 5, 23, 1, 1, 5),
|
|
MIX_NONE(SOUND_MIXER_BASS),
|
|
MIX_NONE(SOUND_MIXER_TREBLE),
|
|
MIX_ENT(SOUND_MIXER_SYNTH, 4, 1, 1, 4, 5, 1, 1, 4),
|
|
MIX_ENT(SOUND_MIXER_PCM, 6, 1, 0, 5, 7, 1, 0, 5),
|
|
MIX_NONE(SOUND_MIXER_SPEAKER),
|
|
MIX_ENT(SOUND_MIXER_LINE, 18, 1, 1, 4, 19, 1, 1, 4),
|
|
MIX_ENT(SOUND_MIXER_MIC, 0, 0, 5, 1, 1, 0, 5, 1),
|
|
MIX_ENT(SOUND_MIXER_CD, 2, 1, 1, 4, 3, 1, 1, 4),
|
|
MIX_NONE(SOUND_MIXER_IMIX),
|
|
MIX_NONE(SOUND_MIXER_ALTPCM),
|
|
MIX_NONE(SOUND_MIXER_RECLEV),
|
|
MIX_ENT(SOUND_MIXER_IGAIN, 0, 0, 0, 4, 1, 0, 0, 4),
|
|
MIX_NONE(SOUND_MIXER_OGAIN),
|
|
MIX_ENT(SOUND_MIXER_LINE1, 16, 1, 1, 4, 17, 1, 1, 4),
|
|
MIX_NONE(SOUND_MIXER_LINE2),
|
|
MIX_NONE(SOUND_MIXER_LINE3),
|
|
};
|
|
|
|
#define OPTI931_MIXER_DEVICES \
|
|
(SOUND_MASK_VOLUME | SOUND_MASK_SYNTH | SOUND_MASK_PCM | \
|
|
SOUND_MASK_LINE | SOUND_MASK_MIC | SOUND_MASK_CD | \
|
|
SOUND_MASK_IGAIN | SOUND_MASK_LINE1 )
|
|
|
|
/*-
|
|
* Copyright (c) 1999 Doug Rabson
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*
|
|
* $FreeBSD$
|
|
*/
|
|
|
|
/*
|
|
* Register definitions for the Yamaha OPL3-SA[23x].
|
|
*/
|
|
#define OPL3SAx_POWER 0x01 /* Power Management (R/W) */
|
|
#define OPL3SAx_POWER_PDX 0x01 /* Set to 1 to halt oscillator */
|
|
#define OPL3SAx_POWER_PDN 0x02 /* Set to 1 to power down */
|
|
#define OPL3SAx_POWER_PSV 0x04 /* Set to 1 to power save */
|
|
#define OPL3SAx_POWER_ADOWN 0x20 /* Analog power (?) */
|
|
|
|
#define OPL3SAx_SYSTEM 0x02 /* System control (R/W) */
|
|
#define OPL3SAx_SYSTEM_VZE 0x01 /* I2S audio routing */
|
|
#define OPL3SAx_SYSTEM_IDSEL 0x03 /* SB compat version select */
|
|
#define OPL3SAx_SYSTEM_SBHE 0x80 /* 0 for AT bus, 1 for XT bus */
|
|
|
|
#define OPL3SAx_IRQCONF 0x03 /* Interrupt configuration (R/W */
|
|
#define OPL3SAx_IRQCONF_WSSA 0x01 /* WSS interrupts through IRQA */
|
|
#define OPL3SAx_IRQCONF_SBA 0x02 /* WSS interrupts through IRQA */
|
|
#define OPL3SAx_IRQCONF_MPUA 0x04 /* WSS interrupts through IRQA */
|
|
#define OPL3SAx_IRQCONF_OPL3A 0x08 /* WSS interrupts through IRQA */
|
|
#define OPL3SAx_IRQCONF_WSSB 0x10 /* WSS interrupts through IRQB */
|
|
#define OPL3SAx_IRQCONF_SBB 0x20 /* WSS interrupts through IRQB */
|
|
#define OPL3SAx_IRQCONF_MPUB 0x40 /* WSS interrupts through IRQB */
|
|
#define OPL3SAx_IRQCONF_OPL3B 0x80 /* WSS interrupts through IRQB */
|
|
|
|
#define OPL3SAx_IRQSTATUSA 0x04 /* Interrupt (IRQ-A) Status (RO) */
|
|
#define OPL3SAx_IRQSTATUSB 0x05 /* Interrupt (IRQ-B) Status (RO) */
|
|
#define OPL3SAx_IRQSTATUS_PI 0x01 /* Playback Flag of CODEC */
|
|
#define OPL3SAx_IRQSTATUS_CI 0x02 /* Recording Flag of CODEC */
|
|
#define OPL3SAx_IRQSTATUS_TI 0x04 /* Timer Flag of CODEC */
|
|
#define OPL3SAx_IRQSTATUS_SB 0x08 /* SB compat Playback Interrupt Flag */
|
|
#define OPL3SAx_IRQSTATUS_MPU 0x10 /* MPU401 Interrupt Flag */
|
|
#define OPL3SAx_IRQSTATUS_OPL3 0x20 /* Internal FM Timer Flag */
|
|
#define OPL3SAx_IRQSTATUS_MV 0x40 /* HW Volume Interrupt Flag */
|
|
#define OPL3SAx_IRQSTATUS_PI 0x01 /* Playback Flag of CODEC */
|
|
#define OPL3SAx_IRQSTATUS_CI 0x02 /* Recording Flag of CODEC */
|
|
#define OPL3SAx_IRQSTATUS_TI 0x04 /* Timer Flag of CODEC */
|
|
#define OPL3SAx_IRQSTATUS_SB 0x08 /* SB compat Playback Interrupt Flag */
|
|
#define OPL3SAx_IRQSTATUS_MPU 0x10 /* MPU401 Interrupt Flag */
|
|
#define OPL3SAx_IRQSTATUS_OPL3 0x20 /* Internal FM Timer Flag */
|
|
#define OPL3SAx_IRQSTATUS_MV 0x40 /* HW Volume Interrupt Flag */
|
|
|
|
#define OPL3SAx_DMACONF 0x06 /* DMA configuration (R/W) */
|
|
#define OPL3SAx_DMACONF_WSSPA 0x01 /* WSS Playback on DMA-A */
|
|
#define OPL3SAx_DMACONF_WSSRA 0x02 /* WSS Recording on DMA-A */
|
|
#define OPL3SAx_DMACONF_SBA 0x02 /* SB Playback on DMA-A */
|
|
#define OPL3SAx_DMACONF_WSSPB 0x10 /* WSS Playback on DMA-A */
|
|
#define OPL3SAx_DMACONF_WSSRB 0x20 /* WSS Recording on DMA-A */
|
|
#define OPL3SAx_DMACONF_SBB 0x20 /* SB Playback on DMA-A */
|
|
|
|
#define OPL3SAx_VOLUMEL 0x07 /* Master Volume Left (R/W) */
|
|
#define OPL3SAx_VOLUMEL_MVL 0x0f /* Attenuation level */
|
|
#define OPL3SAx_VOLUMEL_MVLM 0x80 /* Mute */
|
|
|
|
#define OPL3SAx_VOLUMER 0x08 /* Master Volume Right (R/W) */
|
|
#define OPL3SAx_VOLUMER_MVR 0x0f /* Attenuation level */
|
|
#define OPL3SAx_VOLUMER_MVRM 0x80 /* Mute */
|
|
|
|
#define OPL3SAx_MIC 0x09 /* MIC Volume (R/W) */
|
|
#define OPL3SAx_VOLUMER_MCV 0x1f /* Attenuation level */
|
|
#define OPL3SAx_VOLUMER_MICM 0x80 /* Mute */
|
|
|
|
#define OPL3SAx_MISC 0x0a /* Miscellaneous */
|
|
#define OPL3SAx_MISC_VER 0x07 /* Version */
|
|
#define OPL3SAx_MISC_MODE 0x08 /* SB or WSS mode */
|
|
#define OPL3SAx_MISC_MCSW 0x10 /* */
|
|
#define OPL3SAx_MISC_VEN 0x80 /* Enable hardware volume control */
|
|
|
|
#define OPL3SAx_WSSDMA 0x0b /* WSS DMA Counter (RW) (4 regs) */
|
|
|
|
#define OPL3SAx_WSSIRQSCAN 0x0f /* WSS Interrupt Scan out/in (R/W) */
|
|
#define OPL3SAx_WSSIRQSCAN_SPI 0x01
|
|
#define OPL3SAx_WSSIRQSCAN_SCI 0x02
|
|
#define OPL3SAx_WSSIRQSCAN_STI 0x04
|
|
|
|
#define OPL3SAx_SBSTATE 0x10 /* SB compat Internal State (R/W) */
|
|
#define OPL3SAx_SBSTATE_SBPDR 0x01 /* SB Power Down Request */
|
|
#define OPL3SAx_SBSTATE_SE 0x02 /* Scan Enable */
|
|
#define OPL3SAx_SBSTATE_SM 0x04 /* Scan Mode */
|
|
#define OPL3SAx_SBSTATE_SS 0x08 /* Scan Select */
|
|
#define OPL3SAx_SBSTATE_SBPDA 0x80 /* SB Power Down Acknowledge */
|
|
|
|
#define OPL3SAx_SBDATA 0x11 /* SB compat State Scan Data (R/W) */
|
|
|
|
#define OPL3SAx_DIGITALPOWER 0x12 /* Digital Partial Power Down (R/W) */
|
|
#define OPL3SAx_DIGITALPOWER_PnP 0x01
|
|
#define OPL3SAx_DIGITALPOWER_SB 0x02
|
|
#define OPL3SAx_DIGITALPOWER_WSSP 0x04
|
|
#define OPL3SAx_DIGITALPOWER_WSSR 0x08
|
|
#define OPL3SAx_DIGITALPOWER_FM 0x10
|
|
#define OPL3SAx_DIGITALPOWER_MCLK0 0x20
|
|
#define OPL3SAx_DIGITALPOWER_MPU 0x40
|
|
#define OPL3SAx_DIGITALPOWER_JOY 0x80
|
|
|
|
#define OPL3SAx_ANALOGPOWER 0x13 /* Analog Partial Power Down (R/W) */
|
|
#define OPL3SAx_ANALOGPOWER_WIDE 0x01
|
|
#define OPL3SAx_ANALOGPOWER_SBDAC 0x02
|
|
#define OPL3SAx_ANALOGPOWER_DA 0x04
|
|
#define OPL3SAx_ANALOGPOWER_AD 0x08
|
|
#define OPL3SAx_ANALOGPOWER_FMDAC 0x10
|
|
|
|
#define OPL3SAx_WIDE 0x14 /* Enhanced control(WIDE) (R/W) */
|
|
#define OPL3SAx_WIDE_WIDEL 0x07 /* Wide level on Left Channel */
|
|
#define OPL3SAx_WIDE_WIDER 0x70 /* Wide level on Right Channel */
|
|
|
|
#define OPL3SAx_BASS 0x15 /* Enhanced control(BASS) (R/W) */
|
|
#define OPL3SAx_BASS_BASSL 0x07 /* Bass level on Left Channel */
|
|
#define OPL3SAx_BASS_BASSR 0x70 /* Bass level on Right Channel */
|
|
|
|
#define OPL3SAx_TREBLE 0x16 /* Enhanced control(TREBLE) (R/W) */
|
|
#define OPL3SAx_TREBLE_TREBLEL 0x07 /* Treble level on Left Channel */
|
|
#define OPL3SAx_TREBLE_TREBLER 0x70 /* Treble level on Right Channel */
|
|
|
|
#define OPL3SAx_HWVOL 0x17 /* HW Volume IRQ Configuration (R/W) */
|
|
#define OPL3SAx_HWVOL_IRQA 0x10 /* HW Volume IRQ on IRQ-A */
|
|
#define OPL3SAx_HWVOL_IRQB 0x20 /* HW Volume IRQ on IRQ-B */
|
|
|
|
|