mirror of
https://git.FreeBSD.org/src.git
synced 2024-12-24 11:29:10 +00:00
93f0f2e040
and miscellaneous programs which get installed into /usr/distbin. Install now recognizes existing DOS partitions and attempts to install after them. Theoretically, it also remaps badblocks. N.B.: The fourth install floppy must have a clean DOS FAT. Building the new distribution floppies is untested TODO: Build a disktab entry for existing DOS partitions (except extended partitions). This would allow loading and/or extracting the distribution files directly from the DOS hard disk partition.
117 lines
4.8 KiB
Plaintext
117 lines
4.8 KiB
Plaintext
INSTALLATION INSTRUCTIONS FOR FreeBSD 1.0 GAMMA
|
|
|
|
Welcome to FreeBSD! This document has been put together in an effort
|
|
to make initial installation of the system as easy as possible.
|
|
|
|
1. To install FreeBSD you will need 3 floppies, as well as the bulk of
|
|
the distribution on some other medium (floppy, tape, CD, etc). If
|
|
you've retrieved this release from the net, you'll first have to make
|
|
the floppies yourself using the supplied images.
|
|
|
|
Due to the differences in PC configurations, we've found it necessary
|
|
to provide multiple initial boot images that provide kernels for
|
|
different types of systems.
|
|
|
|
If your disk controller is one of:
|
|
|
|
IDE/ST506
|
|
Adaptec 1542{A,B,C}
|
|
Adaptec 1742A
|
|
|
|
Then please use the disk image: kcopy-ah-floppy
|
|
to construct your boot floppy.
|
|
|
|
If your disk controller is one of:
|
|
|
|
Bustek 742a
|
|
UltraStore {14,34}F
|
|
|
|
Then please use the disk image: kcopy-bt-floppy
|
|
to construct your boot floppy.
|
|
|
|
Next, make a second floppy from the disk image: filesystem-floppy
|
|
You'll need this for the second stage of the boot process.
|
|
|
|
Next, make a third floppy from the disk image: cpio-floppy
|
|
You'll need this for the last stage of the boot process.
|
|
|
|
Finally, make a fourth floppy from the disk image: dos-floppy
|
|
You'll need this for the last stage of the boot process.
|
|
This disk is MS-DOS readable and contains the os-bs boot manager
|
|
(for if you are installing more than one operating system on disk.)
|
|
|
|
2. Boot the first floppy. When it asks you to insert the file system,
|
|
insert your second ``filesystem-floppy.'' Follow the instructions
|
|
that floppy gives you, making note of the type of disk it says to
|
|
copy the kernel to, ``sd0a'' or ``wd0a'' (``sd0a'' is for SCSI systems,
|
|
``wd0a'' is for all others.) When the system halts, go on to the next
|
|
step.
|
|
|
|
3. Boot the first floppy again, but this time when it asks
|
|
you to insert the file system floppy, just press the return key.
|
|
Follow the instructions that the floppy gives you. When you see
|
|
the ``kc>'' prompt, type ``copy'' (without quotes). At the next prompt,
|
|
``copy kernel to>'', type either ``sd0a'' or ``wd0a'' as given in
|
|
the previous step. When the system halts, go on to the next step.
|
|
|
|
4. Making sure that there's no floppy in the drive, press return to boot
|
|
from the hard disk. After it has booted and is asking what drive the
|
|
cpio floppy is in, insert the third floppy (cpio-floppy) into a
|
|
floppy drive and answer the question about what drive it is in.
|
|
Note that 0 is the same as DOS drive A:, and 1 is the same as DOS
|
|
drive B:
|
|
|
|
5. After the cpio-floppy has been copied to the disk, remove it from the
|
|
drive and insert the fourth floppy (dos-floppy). Again, specify the
|
|
drive to read from.
|
|
|
|
5. After the dos-floppy has been copied to the disk, enter `halt' at
|
|
the command prompt.
|
|
|
|
6. When the system asks you to press the return key to reboot, first
|
|
remove the floppy and then press the return key to boot from the hard
|
|
disk.
|
|
|
|
7. At this point you will get 4 errors from the fsck on boot, this
|
|
is normal and is caused by files that were open when the
|
|
/dev entries were built - just ignore them. The system will
|
|
correct these errors and then halt, after which you should press
|
|
the return key again to reboot with a clean system.
|
|
|
|
8. Congratulations, you've got the mini FreeBSD system on the disk!
|
|
|
|
9. Follow the instructions about set_tmp_dir and extract that
|
|
will come on your screen after you've pressed the return key.
|
|
|
|
10. You will get the following errors while extracting the bin
|
|
distribution, you can safely ignore them.
|
|
|
|
/tmp/tar: Could not create file bin/sh : Text file busy
|
|
/tmp/tar: Could not create file sbin/init : Text file busy
|
|
/tmp/tar: Could not link .profile to root/.profile : File exists
|
|
|
|
11. Run the configure command to set up some of the /etc files by
|
|
typing ``configure''. You will have to edit /etc/netstart after
|
|
this if you have a networking interface.
|
|
|
|
12. Reboot so that the system comes up multiuser by typing ``reboot''.
|
|
|
|
13. You are now running FreeBSD! Congradulations! You may now continue
|
|
with installing the source distribution, or stop here for now.
|
|
|
|
Should you decided to postpone further installation, you should
|
|
probably save the ``installing profile'' for possible future use by
|
|
saving it and linking a default profile into place.
|
|
|
|
Do it like this:
|
|
|
|
mv /.profile /.profile.install
|
|
ln /root/.profile /.profile
|
|
|
|
14. In addition to the source and binary distributions, many additional
|
|
packages, such as X11 and TeX, may be obtained from freebsd.cdrom.com -
|
|
please have a look around! You may also find this a good time to
|
|
read the release notes in /usr/src/RELNOTES.FreeBSD.
|
|
|
|
End of $Id: floppy.install_notes,v 1.3 1993/09/02 02:04:33 rgrimes Exp $
|