mirror/freebsd
1
0
Fork 0
mirror of https://git.FreeBSD.org/src.git synced 2024-12-29 12:03:03 +00:00
Code Issues Releases Activity
9e0f2a9fb1
freebsd/sys/conf/NOTES
Peter Wemm 4e64b0d320 Document and supply COMPAT_OLDPCI and COMPAT_OLDISA so 'make release' 
still works.
2000-03-19 13:33:26 +00:00

2344 lines
83 KiB
Plaintext
Raw Blame History

This file contains invisible Unicode characters

This file contains invisible Unicode characters that are indistinguishable to humans but may be processed differently by a computer. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

#
# LINT -- config file for checking all the sources, tries to pull in
# as much of the source tree as it can.
#
# $FreeBSD$
#
# NB: You probably don't want to try running a kernel built from this
# file. Instead, you should start from GENERIC, and add options from
# this file as required.
#
#
# This directive is mandatory; it defines the architecture to be
# configured for; in this case, the 386 family based IBM-PC and
# compatibles.
#
machine i386
#
# This is the ``identification'' of the kernel. Usually this should
# be the same as the name of your kernel.
#
ident LINT
#
# The `maxusers' parameter controls the static sizing of a number of
# internal system tables by a complicated formula defined in param.c.
#
maxusers 10
#
# The `makeoptions' parameter allows variables to be passed to the
# generated Makefile in the build area.
#
# CONF_CFLAGS gives some extra compiler flags that are added to ${CFLAGS}
# after most other flags. Here we use it to inhibit use of non-optimal
# gcc builtin functions (e.g., memcmp).
#
# DEBUG happens to be magic.
# The following is equivalent to 'config -g KERNELNAME' and creates
# 'kernel.debug' compiled with -g debugging as well as a normal
# 'kernel'. Use 'make install.debug' to install the debug kernel
# but that isn't normally necessary as the debug symbols are not loaded
# by the kernel and are not useful there anyway.
#
# KERNEL can be overridden so that you can change the default name of your
# kernel.
#
makeoptions CONF_CFLAGS=-fno-builtin #Don't allow use of memcmp, etc.
#makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
#makeoptions KERNEL=foo #Build kernel "foo" and install "/foo"
#
# Certain applications can grow to be larger than the 128M limit
# that FreeBSD initially imposes. Below are some options to
# allow that limit to grow to 256MB, and can be increased further
# with changing the parameters. MAXDSIZ is the maximum that the
# limit can be set to, and the DFLDSIZ is the default value for
# the limit. You might want to set the default lower than the
# max, and explicitly set the maximum with a shell command for processes
# that regularly exceed the limit like INND.
#
options MAXDSIZ="(256*1024*1024)"
options DFLDSIZ="(256*1024*1024)"
#
# BLKDEV_IOSIZE sets the default block size used in user block
# device I/O. Note that this value will be overriden by the label
# when specifying a block device from a label with a non-0
# partition blocksize. The default is PAGE_SIZE.
#
options BLKDEV_IOSIZE=8192
# Options for the VM subsystem
#options PQ_NOOPT # No coloring
options PQ_LARGECACHE # color for 512k/16k cache
#options PQ_HUGECACHE # color for 1024k/16k cache
#options PQ_MEDIUMCACHE # color for 64k/16k cache
#options PQ_NORMALCACHE # color for 256k/16k cache
# This allows you to actually store this configuration file into
# the kernel binary itself, where it may be later read by saying:
# strings -aout -n 3 /kernel | grep ^___ | sed -e 's/^___//' > MYKERNEL
#
options INCLUDE_CONFIG_FILE # Include this file in kernel
#####################################################################
# SMP OPTIONS:
#
# SMP enables building of a Symmetric MultiProcessor Kernel.
# APIC_IO enables the use of the IO APIC for Symmetric I/O.
# NCPU sets the number of CPUs, defaults to 2.
# NBUS sets the number of busses, defaults to 4.
# NAPIC sets the number of IO APICs on the motherboard, defaults to 1.
# NINTR sets the total number of INTs provided by the motherboard.
#
# Notes:
#
# An SMP kernel will ONLY run on an Intel MP spec. qualified motherboard.
#
# Be sure to disable 'cpu I386_CPU' && 'cpu I486_CPU' for SMP kernels.
#
# Check the 'Rogue SMP hardware' section to see if additional options
# are required by your hardware.
#
# Mandatory:
options SMP # Symmetric MultiProcessor Kernel
options APIC_IO # Symmetric (APIC) I/O
# Optional, these are the defaults plus 1:
options NCPU=5 # number of CPUs
options NBUS=5 # number of busses
options NAPIC=2 # number of IO APICs
options NINTR=25 # number of INTs
#
# Rogue SMP hardware:
#
# Bridged PCI cards:
#
# The MP tables of most of the current generation MP motherboards
# do NOT properly support bridged PCI cards. To use one of these
# cards you should refer to ???
#####################################################################
# CPU OPTIONS
#
# You must specify at least one CPU (the one you intend to run on);
# deleting the specification for CPUs you don't need to use may make
# parts of the system run faster. This is especially true removing
# I386_CPU.
#
cpu I386_CPU
cpu I486_CPU
cpu I586_CPU # aka Pentium(tm)
cpu I686_CPU # aka Pentium Pro(tm)
#
# Options for CPU features.
#
# CPU_BLUELIGHTNING_FPU_OP_CACHE enables FPU operand cache on IBM
# BlueLightning CPU. It works only with Cyrix FPU, and this option
# should not be used with Intel FPU.
#
# CPU_BLUELIGHTNING_3X enables triple-clock mode on IBM Blue Lightning
# CPU if CPU supports it. The default is double-clock mode on
# BlueLightning CPU box.
#
# CPU_BTB_EN enables branch target buffer on Cyrix 5x86 (NOTE 1).
#
# CPU_DIRECT_MAPPED_CACHE sets L1 cache of Cyrix 486DLC CPU in direct
# mapped mode. Default is 2-way set associative mode.
#
# CPU_CYRIX_NO_LOCK enables weak locking for the entire address space
# of Cyrix 6x86 and 6x86MX CPUs by setting the NO_LOCK bit of CCR1.
# Otherwise, the NO_LOCK bit of CCR1 is cleared. (NOTE 3)
#
# CPU_DISABLE_5X86_LSSER disables load store serialize (i.e. enables
# reorder). This option should not be used if you use memory mapped
# I/O device(s).
#
# CPU_FASTER_5X86_FPU enables faster FPU exception handler.
#
# CPU_I486_ON_386 enables CPU cache on i486 based CPU upgrade products
# for i386 machines.
#
# CPU_IORT defines I/O clock delay time (NOTE 1). Default values of
# I/O clock delay time on Cyrix 5x86 and 6x86 are 0 and 7,respectively
# (no clock delay).
#
# CPU_LOOP_EN prevents flushing the prefetch buffer if the destination
# of a jump is already present in the prefetch buffer on Cyrix 5x86(NOTE
# 1).
#
# CPU_RSTK_EN enables return stack on Cyrix 5x86 (NOTE 1).
#
# CPU_SUSP_HLT enables suspend on HALT. If this option is set, CPU
# enters suspend mode following execution of HALT instruction.
#
# CPU_WT_ALLOC enables write allocation on Cyrix 6x86/6x86MX and AMD
# K5/K6/K6-2 cpus.
#
# CYRIX_CACHE_WORKS enables CPU cache on Cyrix 486 CPUs with cache
# flush at hold state.
#
# CYRIX_CACHE_REALLY_WORKS enables (1) CPU cache on Cyrix 486 CPUs
# without cache flush at hold state, and (2) write-back CPU cache on
# Cyrix 6x86 whose revision < 2.7 (NOTE 2).
#
# NO_F00F_HACK disables the hack that prevents Pentiums (and ONLY
# Pentiums) from locking up when a LOCK CMPXCHG8B instruction is
# executed. This should be included for ALL kernels that won't run
# on a Pentium.
#
# NO_MEMORY_HOLE is an optimisation for systems with AMD K6 processors
# which indicates that the 15-16MB range is *definitely* not being
# occupied by an ISA memory hole.
#
# NOTE 1: The options, CPU_BTB_EN, CPU_LOOP_EN, CPU_IORT,
# CPU_LOOP_EN and CPU_RSTK_EN should not be used because of CPU bugs.
# These options may crash your system.
#
# NOTE 2: If CYRIX_CACHE_REALLY_WORKS is not set, CPU cache is enabled
# in write-through mode when revision < 2.7. If revision of Cyrix
# 6x86 >= 2.7, CPU cache is always enabled in write-back mode.
#
# NOTE 3: This option may cause failures for software that requires
# locked cycles in order to operate correctly.
#
options CPU_BLUELIGHTNING_FPU_OP_CACHE
options CPU_BLUELIGHTNING_3X
options CPU_BTB_EN
options CPU_DIRECT_MAPPED_CACHE
options CPU_DISABLE_5X86_LSSER
options CPU_FASTER_5X86_FPU
options CPU_I486_ON_386
options CPU_IORT
options CPU_LOOP_EN
options CPU_RSTK_EN
options CPU_SUSP_HLT
options CPU_WT_ALLOC
options CYRIX_CACHE_WORKS
options CYRIX_CACHE_REALLY_WORKS
#options NO_F00F_HACK
#
# A math emulator is mandatory if you wish to run on hardware which
# does not have a floating-point processor. Pick either the original,
# bogus (but freely-distributable) math emulator, or a much more
# fully-featured but GPL-licensed emulator taken from Linux.
#
options MATH_EMULATE #Support for x87 emulation
# Don't enable both of these in a real config.
options GPL_MATH_EMULATE #Support for x87 emulation via
#new math emulator
#####################################################################
# COMPATIBILITY OPTIONS
#
# Implement system calls compatible with 4.3BSD and older versions of
# FreeBSD. You probably do NOT want to remove this as much current code
# still relies on the 4.3 emulation.
#
options COMPAT_43
#
# Allow user-mode programs to manipulate their local descriptor tables.
# This option is required for the WINE Windows(tm) emulator, and is
# not used by anything else (that we know of).
#
options USER_LDT #allow user-level control of i386 ldt
#
# These three options provide support for System V Interface
# Definition-style interprocess communication, in the form of shared
# memory, semaphores, and message queues, respectively.
#
options SYSVSHM
options SYSVSEM
options SYSVMSG
#####################################################################
# DEBUGGING OPTIONS
#
# Enable the kernel debugger.
#
options DDB
#
# Don't drop into DDB for a panic. Intended for unattended operation
# where you may want to drop to DDB from the console, but still want
# the machine to recover from a panic
#
options DDB_UNATTENDED
#
# If using GDB remote mode to debug the kernel, there's a non-standard
# extension to the remote protocol that can be used to use the serial
# port as both the debugging port and the system console. It's non-
# standard and you're on your own if you enable it. See also the
# "remotechat" variables in the FreeBSD specific version of gdb.
#
options GDB_REMOTE_CHAT
#
# KTRACE enables the system-call tracing facility ktrace(2).
#
options KTRACE #kernel tracing
#
# The INVARIANTS option is used in a number of source files to enable
# extra sanity checking of internal structures. This support is not
# enabled by default because of the extra time it would take to check
# for these conditions, which can only occur as a result of
# programming errors.
#
options INVARIANTS
#
# The INVARIANT_SUPPORT option makes us compile in support for
# verifying some of the internal structures. It is a prerequisite for
# 'INVARIANTS', as enabling 'INVARIANTS' will make these functions be
# called. The intent is that you can set 'INVARIANTS' for single
# source files (by changing the source file or specifying it on the
# command line) if you have 'INVARIANT_SUPPORT' enabled.
#
options INVARIANT_SUPPORT
#
# The DIAGNOSTIC option is used to enable extra debugging information
# from some parts of the kernel. As this makes everything more noisy,
# it is disabled by default.
#
options DIAGNOSTIC
#
# PERFMON causes the driver for Pentium/Pentium Pro performance counters
# to be compiled. See perfmon(4) for more information.
#
options PERFMON
#
# This option let some drivers co-exist that can't co-exist in a running
# system. This is used to be able to compile all kernel code in one go for
# quality assurance purposes (like this file, which the option takes it name
# from.)
#
options COMPILING_LINT
# XXX - this doesn't belong here.
# Allow ordinary users to take the console - this is useful for X.
options UCONSOLE
# XXX - this doesn't belong here either
options USERCONFIG #boot -c editor
options INTRO_USERCONFIG #imply -c and show intro screen
options VISUAL_USERCONFIG #visual boot -c editor
# XXX - neither does this
options ROOTDEVNAME=\"da0s2e\"
#####################################################################
# NETWORKING OPTIONS
#
# Protocol families:
# Only the INET (Internet) family is officially supported in FreeBSD.
# Source code for the NS (Xerox Network Service) is provided for amusement
# value.
#
options INET #Internet communications protocols
options INET6 #IPv6 communications protocols
options IPSEC #IP security
options IPSEC_ESP #IP security (crypto; define w/ IPSEC)
options IPSEC_IPV6FWD #IP security tunnel for IPv6
options IPSEC_DEBUG #debug for IP security
options IPX #IPX/SPX communications protocols
options IPXIP #IPX in IP encapsulation (not available)
options IPTUNNEL #IP in IPX encapsulation (not available)
options NCP #NetWare Core protocol
options NETATALK #Appletalk communications protocols
# These are currently broken but are shipped due to interest.
#options NS #Xerox NS protocols
#options NSIP #XNS over IP
# netgraph(4). Enable the base netgraph code with the NETGRAPH option.
# Individual node types can be enabled with the corresponding option
# listed below; however, this is not strictly necessary as netgraph
# will automatically load the corresponding KLD module if the node type
# is not already compiled into the kernel. Each type below has a
# corresponding man page, e.g., ng_async(8).
options NETGRAPH #netgraph(4) system
options NETGRAPH_ASYNC
options NETGRAPH_BPF
options NETGRAPH_CISCO
options NETGRAPH_ECHO
options NETGRAPH_FRAME_RELAY
options NETGRAPH_HOLE
options NETGRAPH_IFACE
options NETGRAPH_KSOCKET
options NETGRAPH_LMI
options NETGRAPH_PPP
options NETGRAPH_PPPOE
options NETGRAPH_PPTPGRE
options NETGRAPH_RFC1490
options NETGRAPH_SOCKET
options NETGRAPH_TEE
options NETGRAPH_TTY
options NETGRAPH_UI
options NETGRAPH_VJC
device mn # Munich32x/Falc54 Nx64kbit/sec cards.
#
# Network interfaces:
# The `loop' pseudo-device is MANDATORY when networking is enabled.
# The `ether' pseudo-device provides generic code to handle
# Ethernets; it is MANDATORY when a Ethernet device driver is
# configured or token-ring is enabled.
# The 'fddi' pseudo-device provides generic code to support FDDI.
# The `sppp' pseudo-device serves a similar role for certain types
# of synchronous PPP links (like `cx', `ar').
# The `sl' pseudo-device implements the Serial Line IP (SLIP) service.
# The `ppp' pseudo-device implements the Point-to-Point Protocol.
# The `bpf' pseudo-device enables the Berkeley Packet Filter. Be
# aware of the legal and administrative consequences of enabling this
# option. The number of devices determines the maximum number of
# simultaneous BPF clients programs runnable.
# The `disc' pseudo-device implements a minimal network interface,
# which throws away all packets sent and never receives any. It is
# included for testing purposes. This shows up as the 'ds' interface.
# The `tun' pseudo-device implements (user-)ppp and nos-tun
# The `gif' pseudo-device implements IPv6 over IP4 tunneling,
# IPv4 over IPv6 tunneling, IPv4 over IPv4 tunneling and
# IPv6 over IPv6 tunneling.
# The `faith' pseudo-device captures packets sent to it and diverts them
# to the IPv4/IPv6 translation daemon.
# The `ef' pseudo-device provides support for multiple ethernet frame types
# specified via ETHER_* options. See ef(4) for details.
#
# The PPP_BSDCOMP option enables support for compress(1) style entire
# packet compression, the PPP_DEFLATE is for zlib/gzip style compression.
# PPP_FILTER enables code for filtering the ppp data stream and selecting
# events for resetting the demand dial activity timer - requires bpf.
# See pppd(8) for more details.
#
pseudo-device ether #Generic Ethernet
pseudo-device token #Generic TokenRing
pseudo-device fddi #Generic FDDI
pseudo-device sppp #Generic Synchronous PPP
pseudo-device loop #Network loopback device
pseudo-device bpf #Berkeley packet filter
pseudo-device disc #Discard device (ds0, ds1, etc)
pseudo-device tun #Tunnel driver (ppp(8), nos-tun(8))
pseudo-device sl 2 #Serial Line IP
pseudo-device ppp 2 #Point-to-point protocol
options PPP_BSDCOMP #PPP BSD-compress support
options PPP_DEFLATE #PPP zlib/deflate/gzip support
options PPP_FILTER #enable bpf filtering (needs bpf)
pseudo-device ef # Multiple ethernet frames support
options ETHER_II # enable Ethernet_II frame
options ETHER_8023 # enable Ethernet_802.3 (Novell) frame
options ETHER_8022 # enable Ethernet_802.2 frame
options ETHER_SNAP # enable Ethernet_802.2/SNAP frame
# for IPv6
pseudo-device gif 4 #IPv6 and IPv4 tunneling
pseudo-device faith 1 #for IPv6 and IPv4 translation
#
# Internet family options:
#
# TCP_COMPAT_42 causes the TCP code to emulate certain bugs present in
# 4.2BSD. This option should not be used unless you have a 4.2BSD
# machine and TCP connections fail.
#
# MROUTING enables the kernel multicast packet forwarder, which works
# with mrouted(8).
#
# IPFIREWALL enables support for IP firewall construction, in
# conjunction with the `ipfw' program. IPFIREWALL_VERBOSE sends
# logged packets to the system logger. IPFIREWALL_VERBOSE_LIMIT
# limits the number of times a matching entry can be logged.
#
# WARNING: IPFIREWALL defaults to a policy of "deny ip from any to any"
# and if you do not add other rules during startup to allow access,
# YOU WILL LOCK YOURSELF OUT. It is suggested that you set firewall_type=open
# in /etc/rc.conf when first enabling this feature, then refining the
# firewall rules in /etc/rc.firewall after you've tested that the new kernel
# feature works properly.
#
# IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to
# allow everything. Use with care, if a cracker can crash your
# firewall machine, they can get to your protected machines. However,
# if you are using it as an as-needed filter for specific problems as
# they arise, then this may be for you. Changing the default to 'allow'
# means that you won't get stuck if the kernel and /sbin/ipfw binary get
# out of sync.
#
# IPDIVERT enables the divert IP sockets, used by ``ipfw divert''
#
# IPSTEALTH enables code to support stealth forwarding (i.e., forwarding
# packets without touching the ttl). This can be useful to hide firewalls
# from traceroute and similar tools.
#
# TCPDEBUG is undocumented.
#
options TCP_COMPAT_42 #emulate 4.2BSD TCP bugs
options MROUTING # Multicast routing
options IPFIREWALL #firewall
options IPFIREWALL_VERBOSE #print information about
# dropped packets
options IPFIREWALL_FORWARD #enable transparent proxy support
options IPFIREWALL_VERBOSE_LIMIT=100 #limit verbosity
options IPFIREWALL_DEFAULT_TO_ACCEPT #allow everything by default
options IPV6FIREWALL #firewall for IPv6
options IPV6FIREWALL_VERBOSE
options IPV6FIREWALL_VERBOSE_LIMIT=100
options IPV6FIREWALL_DEFAULT_TO_ACCEPT
options IPDIVERT #divert sockets
options IPFILTER #ipfilter support
options IPFILTER_LOG #ipfilter logging
options IPSTEALTH #support for stealth forwarding
options TCPDEBUG
# The following options add sysctl variables for controlling how certain
# TCP packets are handled.
#
# TCP_DROP_SYNFIN adds support for ignoring TCP packets with SYN+FIN. This
# prevents nmap et al. from identifying the TCP/IP stack, but breaks support
# for RFC1644 extensions and is not recommended for web servers.
#
# TCP_RESTRICT_RST adds support for blocking the emission of TCP RST packets.
# This is useful on systems which are exposed to SYN floods (e.g. IRC servers)
# or any system which one does not want to be easily portscannable.
#
options TCP_DROP_SYNFIN #drop TCP packets with SYN+FIN
options TCP_RESTRICT_RST #restrict emission of TCP RST
# ICMP_BANDLIM enables icmp error response bandwidth limiting. You
# typically want this option as it will help protect the machine from
# D.O.S. packet attacks.
#
options ICMP_BANDLIM
# DUMMYNET enables the "dummynet" bandwidth limiter. You need
# IPFIREWALL as well. See the dummynet(4) manpage for more info.
# BRIDGE enables bridging between ethernet cards -- see bridge(4).
# You can use IPFIREWALL and dummynet together with bridging.
options DUMMYNET
options BRIDGE
#
# ATM (HARP version) options
#
# ATM_CORE includes the base ATM functionality code. This must be included
# for ATM support.
#
# ATM_IP includes support for running IP over ATM.
#
# At least one (and usually only one) of the following signalling managers
# must be included (note that all signalling managers include PVC support):
# ATM_SIGPVC includes support for the PVC-only signalling manager `sigpvc'.
# ATM_SPANS includes support for the `spans' signalling manager, which runs
# the FORE Systems's proprietary SPANS signalling protocol.
# ATM_UNI includes support for the `uni30' and `uni31' signalling managers,
# which run the ATM Forum UNI 3.x signalling protocols.
#
# The `hea' driver provides support for the Efficient Networks, Inc.
# ENI-155p ATM PCI Adapter.
#
# The `hfa' driver provides support for the FORE Systems, Inc.
# PCA-200E ATM PCI Adapter.
#
options ATM_CORE #core ATM protocol family
options ATM_IP #IP over ATM support
options ATM_SIGPVC #SIGPVC signalling manager
options ATM_SPANS #SPANS signalling manager
options ATM_UNI #UNI signalling manager
device hea #Efficient ENI-155p ATM PCI
device hfa #FORE PCA-200E ATM PCI
#####################################################################
# FILESYSTEM OPTIONS
#
# Only the root, /usr, and /tmp filesystems need be statically
# compiled; everything else will be automatically loaded at mount
# time. (Exception: the UFS family---FFS, and MFS --- cannot
# currently be demand-loaded.) Some people still prefer to statically
# compile other filesystems as well.
#
# NB: The NULL, PORTAL, UMAP and UNION filesystems are known to be
# buggy, and WILL panic your system if you attempt to do anything with
# them. They are included here as an incentive for some enterprising
# soul to sit down and fix them.
#
# One of these is mandatory:
options FFS #Fast filesystem
options MFS #Memory File System
options NFS #Network File System
# The rest are optional:
#options NFS_NOSERVER #Disable the NFS-server code.
options CD9660 #ISO 9660 filesystem
options FDESC #File descriptor filesystem
options KERNFS #Kernel filesystem
options MSDOSFS #MS DOS File System
options NTFS #NT File System
options NULLFS #NULL filesystem
options NWFS #NetWare filesystem
options PORTAL #Portal filesystem
options PROCFS #Process filesystem
options UMAPFS #UID map filesystem
options UNION #Union filesystem
# The xFS_ROOT options REQUIRE the associated ``options xFS''
options CD9660_ROOT #CD-ROM usable as root device
options FFS_ROOT #FFS usable as root device
options NFS_ROOT #NFS usable as root device
# This code is still experimental (e.g. doesn't handle disk slices well).
# Also, 'options MFS' is currently incompatible with DEVFS.
options DEVFS #devices filesystem
# Soft updates is technique for improving file system speed and
# making abrupt shutdown less risky. It is not enabled by default due
# to copyright restraints on the code that implement it.
#
# Read ../../ufs/ffs/README.softupdates to learn what you need to
# do to enable this. ../../contrib/softupdates/README gives
# more details on how they actually work.
#
#options SOFTUPDATES
# Make space in the kernel for a root filesystem on a md device.
# Define to the number of kilobytes to reserve for the filesystem.
options MD_ROOT_SIZE=10
# Make the md device a potential root device, either with preloaded
# images of type mfs_root or md_root.
options MD_ROOT
# Allow this many swap-devices.
options NSWAPDEV=20
# Disk quotas are supported when this option is enabled.
options QUOTA #enable disk quotas
# If you are running a machine just as a fileserver for PC and MAC
# users, using SAMBA or Netatalk, you may consider setting this option
# and keeping all those users' directories on a filesystem that is
# mounted with the suiddir option. This gives new files the same
# ownership as the directory (similar to group). It's a security hole
# if you let these users run programs, so confine it to file-servers
# (but it'll save you lots of headaches in those cases). Root owned
# directories are exempt and X bits are cleared. The suid bit must be
# set on the directory as well; see chmod(1) PC owners can't see/set
# ownerships so they keep getting their toes trodden on. This saves
# you all the support calls as the filesystem it's used on will act as
# they expect: "It's my dir so it must be my file".
#
options SUIDDIR
# NFS options:
options NFS_MINATTRTIMO=3 # VREG attrib cache timeout in sec
options NFS_MAXATTRTIMO=60
options NFS_MINDIRATTRTIMO=30 # VDIR attrib cache timeout in sec
options NFS_MAXDIRATTRTIMO=60
options NFS_GATHERDELAY=10 # Default write gather delay (msec)
options NFS_UIDHASHSIZ=29 # Tune the size of nfssvc_sock with this
options NFS_WDELAYHASHSIZ=16 # and with this
options NFS_MUIDHASHSIZ=63 # Tune the size of nfsmount with this
options NFS_DEBUG # Enable NFS Debugging
# Coda stuff:
options CODA #CODA filesystem.
pseudo-device vcoda 4 #coda minicache <-> venus comm.
#
# Add support for the EXT2FS filesystem of Linux fame. Be a bit
# careful with this - the ext2fs code has a tendency to lag behind
# changes and not be exercised very much, so mounting read/write could
# be dangerous (and even mounting read only could result in panics.)
#
options EXT2FS
# Use real implementations of the aio_* system calls. There are numerous
# stability issues in the current aio code that make it unsuitable for
# inclusion on shell boxes.
options VFS_AIO
#####################################################################
# POSIX P1003.1B
# Real time extensions added in the 1993 Posix
# P1003_1B: Infrastructure
# _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING
# _KPOSIX_VERSION: Version kernel is built for
options P1003_1B
options _KPOSIX_PRIORITY_SCHEDULING
options _KPOSIX_VERSION=199309L
#####################################################################
# SCSI DEVICES
# SCSI DEVICE CONFIGURATION
# The SCSI subsystem consists of the `base' SCSI code, a number of
# high-level SCSI device `type' drivers, and the low-level host-adapter
# device drivers. The host adapters are listed in the ISA and PCI
# device configuration sections below.
#
# Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so
# that a given bus, target, and LUN always come on line as the same
# device unit. In earlier versions the unit numbers were assigned
# in the order that the devices were probed on the SCSI bus. This
# means that if you removed a disk drive, you may have had to rewrite
# your /etc/fstab file, and also that you had to be careful when adding
# a new disk as it may have been probed earlier and moved your device
# configuration around.
# This old behavior is maintained as the default behavior. The unit
# assignment begins with the first non-wired down unit for a device
# type. For example, if you wire a disk as "da3" then the first
# non-wired disk will be assigned da4.
# The syntax for wiring down devices is:
# device scbus0 at ahc0 # Single bus device
# device scbus1 at ahc1 bus 0 # Single bus device
# device scbus3 at ahc2 bus 0 # Twin bus device
# device scbus2 at ahc2 bus 1 # Twin bus device
# device da0 at scbus0 target 0 unit 0
# device da1 at scbus3 target 1
# device da2 at scbus2 target 3
# device sa1 at scbus1 target 6
# device cd
# "units" (SCSI logical unit number) that are not specified are
# treated as if specified as LUN 0.
# All SCSI devices allocate as many units as are required.
# The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI
# configuration and doesn't have to be explicitly configured.
device scbus #base SCSI code
device ch #SCSI media changers
device da #SCSI direct access devices (aka disks)
device sa #SCSI tapes
device cd #SCSI CD-ROMs
device pass #CAM passthrough driver
device pt #SCSI processor type
device ses #SCSI SES/SAF-TE driver
# CAM OPTIONS:
# debugging options:
# -- NOTE -- If you specify one of the bus/target/lun options, you must
# specify them all!
# CAMDEBUG: When defined enables debugging macros
# CAM_DEBUG_BUS: Debug the given bus. Use -1 to debug all busses.
# CAM_DEBUG_TARGET: Debug the given target. Use -1 to debug all targets.
# CAM_DEBUG_LUN: Debug the given lun. Use -1 to debug all luns.
# CAM_DEBUG_FLAGS: OR together CAM_DEBUG_INFO, CAM_DEBUG_TRACE,
# CAM_DEBUG_SUBTRACE, and CAM_DEBUG_CDB
#
# CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds
# SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions
# SCSI_NO_OP_STRINGS: When defined disables opcode descriptions
# SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter)
# queue after a bus reset, and the number of milliseconds to
# freeze the device queue after a bus device reset.
options CAMDEBUG
options CAM_DEBUG_BUS=-1
options CAM_DEBUG_TARGET=-1
options CAM_DEBUG_LUN=-1
options CAM_DEBUG_FLAGS="CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB"
options CAM_MAX_HIGHPOWER=4
options SCSI_NO_SENSE_STRINGS
options SCSI_NO_OP_STRINGS
options SCSI_DELAY=8000 # Be pessimistic about Joe SCSI device
# Options for the CAM CDROM driver:
# CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN
# CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only
# enforced if there is I/O waiting for another LUN
# The compiled in defaults for these variables are 2 and 10 seconds,
# respectively.
#
# These can also be changed on the fly with the following sysctl variables:
# kern.cam.cd.changer.min_busy_seconds
# kern.cam.cd.changer.max_busy_seconds
#
options CHANGER_MIN_BUSY_SECONDS=2
options CHANGER_MAX_BUSY_SECONDS=10
# Options for the CAM sequential access driver:
# SA_SPACE_TIMEOUT: Timeout for space operations, in minutes
# SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes
# SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes
# SA_1FM_AT_EOD: Default to model which only has a default one filemark at EOT.
options SA_SPACE_TIMEOUT="(60)"
options SA_REWIND_TIMEOUT="(2*60)"
options SA_ERASE_TIMEOUT="(4*60)"
options SA_1FM_AT_EOD
# Optional timeout for the CAM processor target (pt) device
# This is specified in seconds. The default is 60 seconds.
options SCSI_PT_DEFAULT_TIMEOUT="60"
# Optional enable of doing SES passthrough on other devices (e.g., disks)
#
# Normally disabled because a lot of newer SCSI disks report themselves
# as having SES capabilities, but this can then clot up attempts to build
# build a topology with the SES device that's on the box these drives
# are in....
options SES_ENABLE_PASSTHROUGH
#####################################################################
# MISCELLANEOUS DEVICES AND OPTIONS
# The `pty' device usually turns out to be ``effectively mandatory'',
# as it is required for `telnetd', `rlogind', `screen', `emacs', and
# `xterm', among others.
pseudo-device pty #Pseudo ttys
pseudo-device speaker #Play IBM BASIC-style noises out your speaker
pseudo-device gzip #Exec gzipped a.out's
pseudo-device vn #Vnode driver (turns a file into a device)
pseudo-device md #Memory/malloc disk
pseudo-device snp 3 #Snoop device - to look at pty/vty/etc..
pseudo-device ccd 4 #Concatenated disk driver
# Configuring Vinum into the kernel is not necessary, since the kld
# module gets started automatically when vinum(8) starts. This
# device is also untested. Use at your own risk.
#
# The option VINUMDEBUG must match the value set in CFLAGS
# in src/sbin/vinum/Makefile. Failure to do so will result in
# the following message from vinum(8):
#
# Can't get vinum config: Invalid argument
#
# see vinum(4) for more reasons not to use these options.
pseudo-device vinum #Vinum concat/mirror/raid driver
options VINUMDEBUG #enable Vinum debugging hooks
# Size of the kernel message buffer. Should be N * pagesize.
options MSGBUF_SIZE=40960
#####################################################################
# HARDWARE DEVICE CONFIGURATION
# ISA and EISA devices:
# EISA support is available for some device, so they can be auto-probed.
# MicroChannel (MCA) support is available for some devices.
#
# Mandatory ISA devices: isa, npx
#
device isa
#
# Options for `isa':
#
# AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A
# interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
# This option breaks suspend/resume on some portables.
#
# AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A
# interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
# Automatic EOI is documented not to work for for the slave with the
# original i8259A, but it works for some clones and some integrated
# versions.
#
# MAXMEM specifies the amount of RAM on the machine; if this is not
# specified, FreeBSD will first read the amount of memory from the CMOS
# RAM, so the amount of memory will initially be limited to 64MB or 16MB
# depending on the BIOS. If the BIOS reports 64MB, a memory probe will
# then attempt to detect the installed amount of RAM. If this probe
# fails to detect >64MB RAM you will have to use the MAXMEM option.
# The amount is in kilobytes, so for a machine with 128MB of RAM, it would
# be 131072 (128 * 1024).
#
# BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to
# reset the CPU for reboot. This is needed on some systems with broken
# keyboard controllers.
#
# PAS_JOYSTICK_ENABLE enables the gameport on the ProAudio Spectrum
options AUTO_EOI_1
#options AUTO_EOI_2
options MAXMEM="(128*1024)"
#options BROKEN_KEYBOARD_RESET
#options PAS_JOYSTICK_ENABLE
options COMPAT_OLDPCI #Use PCI shims and glue for old drivers
# Enable support for the kernel PLL to use an external PPS signal,
# under supervision of [x]ntpd(8)
# More info in ntpd documentation: http://www.eecis.udel.edu/~ntp
options PPS_SYNC
# If you see the "calcru: negative time of %ld usec for pid %d (%s)\n"
# message you probably have some broken sw/hw which disables interrupts
# for too long. You can make the system more resistant to this by
# choosing a high value for NTIMECOUNTER. The default is 5, there
# is no upper limit but more than a couple of hundred are not productive.
# A better strategy may be to sysctl -w kern.timecounter.method=1
options NTIMECOUNTER=20
# The keyboard controller; it controls the keyboard and the PS/2 mouse.
device atkbdc0 at isa? port IO_KBD
# The AT keyboard
device atkbd0 at atkbdc? irq 1
# Options for atkbd:
options ATKBD_DFLT_KEYMAP # specify the built-in keymap
makeoptions ATKBD_DFLT_KEYMAP="jp.106"
# These options are valid for other keyboard drivers as well.
options KBD_DISABLE_KEYMAP_LOAD # refuse to load a keymap
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
# `flags' for atkbd:
# 0x01 Force detection of keyboard, else we always assume a keyboard
# 0x02 Don't reset keyboard, useful for some newer ThinkPads
# 0x04 Old-style (XT) keyboard support, useful for older ThinkPads
# PS/2 mouse
device psm0 at atkbdc? irq 12
# Options for psm:
options PSM_HOOKRESUME #hook the system resume event, useful
#for some laptops
options PSM_RESETAFTERSUSPEND #reset the device at the resume event
# The video card driver.
device vga0 at isa?
# Options for vga:
# Try the following option if the mouse pointer is not drawn correctly
# or font does not seem to be loaded properly. May cause flicker on
# some systems.
options VGA_ALT_SEQACCESS
# If you can dispense with some vga driver features, you may want to
# use the following options to save some memory.
options VGA_NO_FONT_LOADING # don't save/load font
options VGA_NO_MODE_CHANGE # don't change video modes
# Older video cards may require this option for proper operation.
options VGA_SLOW_IOACCESS # do byte-wide i/o's to TS and GDC regs
# The following option probably won't work with the LCD displays.
options VGA_WIDTH90 # support 90 column modes
# To include support for VESA video modes
options VESA
# Splash screen at start up! Screen savers require this too.
pseudo-device splash
# The pcvt console driver (vt220 compatible).
device vt0 at isa?
options XSERVER # support for running an X server on vt
options FAT_CURSOR # start with block cursor
# This PCVT option is for keyboards such as those used on IBM ThinkPad laptops
options PCVT_SCANSET=2 # IBM keyboards are non-std
# Other PCVT options are documented in pcvt(4).
options PCVT_24LINESDEF
options PCVT_CTRL_ALT_DEL
options PCVT_EMU_MOUSE
options PCVT_FREEBSD=211
options PCVT_META_ESC
options PCVT_NSCREENS=9
options PCVT_PRETTYSCRNS
options PCVT_SCREENSAVER
options PCVT_USEKBDSEC
options PCVT_VT220KEYB
# The syscons console driver (sco color console compatible).
device sc0 at isa?
options MAXCONS=16 # number of virtual consoles
options SC_ALT_MOUSE_IMAGE # simplified mouse cursor in text mode
options SC_DFLT_FONT # compile font in
makeoptions SC_DFLT_FONT=cp850
options SC_DISABLE_DDBKEY # disable `debug' key
options SC_DISABLE_REBOOT # disable reboot key sequence
options SC_HISTORY_SIZE=200 # number of history buffer lines
options SC_MOUSE_CHAR=0x3 # char code for text mode mouse cursor
options SC_PIXEL_MODE # add support for the raster text mode
# The following options will let you change the default colors of syscons.
options SC_NORM_ATTR="(FG_GREEN|BG_BLACK)"
options SC_NORM_REV_ATTR="(FG_YELLOW|BG_GREEN)"
options SC_KERNEL_CONS_ATTR="(FG_RED|BG_BLACK)"
options SC_KERNEL_CONS_REV_ATTR="(FG_BLACK|BG_RED)"
# If you have a two button mouse, you may want to add the following option
# to use the right button of the mouse to paste text.
options SC_TWOBUTTON_MOUSE
# You can selectively disable features in syscons.
options SC_NO_CUTPASTE
options SC_NO_FONT_LOADING
options SC_NO_HISTORY
options SC_NO_SYSMOUSE
#
# The Numeric Processing eXtension driver. In addition to this, you
# may configure a math emulator (see above). If your machine has a
# hardware FPU and the kernel configuration includes the npx device
# *and* a math emulator compiled into the kernel, the hardware FPU
# will be used, unless it is found to be broken or unless "flags" to
# npx0 includes "0x08", which requests preference for the emulator.
device npx0 at nexus? port IO_NPX flags 0x0 irq 13
#
# `flags' for npx0:
# 0x01 don't use the npx registers to optimize bcopy.
# 0x02 don't use the npx registers to optimize bzero.
# 0x04 don't use the npx registers to optimize copyin or copyout.
# 0x08 use emulator even if hardware FPU is available.
# The npx registers are normally used to optimize copying and zeroing when
# all of the following conditions are satisfied:
# I586_CPU is an option
# the cpu is an i586 (perhaps not a Pentium)
# the probe for npx0 succeeds
# INT 16 exception handling works.
# Then copying and zeroing using the npx registers is normally 30-100% faster.
# The flags can be used to control cases where it doesn't work or is slower.
# Setting them at boot time using userconfig works right (the optimizations
# are not used until later in the bootstrap when npx0 is attached).
# Flag 0x08 automatically disables the i586 optimized routines.
#
#
# Optional ISA and EISA devices:
#
#
# SCSI host adapters: `aha', `aic', `bt'
#
# adv: All Narrow SCSI bus AdvanSys controllers.
# adw: Second Generation AdvanSys controllers including the ADV940UW.
# aha: Adaptec 154x
# ahc: Adaptec 274x/284x/294x
# aic: Adaptec 152x
# bt: Most Buslogic controllers
#
# Note that the order is important in order for Buslogic cards to be
# probed correctly.
#
device bt0 at isa? port IO_BT0
device adv0 at isa?
device adw
device aha0 at isa?
device aic0 at isa?
#
# Compaq Smart RAID, Mylex DAC960 and AMI MegaRAID controllers. Only
# one entry is needed; the code will find and configure all supported
# controllers.
#
device ida # Compaq Smart RAID
device mlx # Mylex DAC960
device amr # AMI MegaRAID
#
# The 'ATA' driver supports all ATA and ATAPI devices.
# You only need one "device ata" for it to find all
# PCI ATA/ATAPI devices on modern machines.
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
device atapist # ATAPI tape drives
#
#The following options are valid on the ATA driver:
#
# ATA_STATIC_ID: controller numbering is static ie depends on location
# else the device numbers are dynamically allocated.
# ATA_ENABLE_ATAPI_DMA: enable DMA on ATAPI device, since many ATAPI devices
# claim to support DMA but doesn't actually work, this
# is not enabled as default.
options ATA_STATIC_ID
options ATA_ENABLE_ATAPI_DMA
#
# For older non-PCI systems, these are the lines to use:
#device ata0 at isa? port IO_WD1 irq 14
#device ata1 at isa? port IO_WD2 irq 15
#
# Standard floppy disk controllers and floppy tapes: `fdc', `fd', and `ft'
#
device fdc0 at isa? port IO_FD1 irq 6 drq 2
#
# FDC_DEBUG enables floppy debugging. Since the debug output is huge, you
# gotta turn it actually on by setting the variable fd_debug with DDB,
# however.
options FDC_DEBUG
#
# Activate this line instead of the fdc0 line above if you happen to
# have an Insight floppy tape. Probing them proved to be dangerous
# for people with floppy disks only, so it's "hidden" behind a flag:
#device fdc0 at isa? port IO_FD1 flags 1 irq 6 drq 2
device fd0 at fdc0 drive 0
device fd1 at fdc0 drive 1
# M-systems DiskOnchip products see src/sys/contrib/dev/fla/README
device fla0 at isa?
#
# Other standard PC hardware: `mse', `sio', etc.
#
# mse: Logitech and ATI InPort bus mouse ports
# sio: serial ports (see sio(4))
device mse0 at isa? port 0x23c irq 5
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
#
# `flags' for serial drivers that support consoles (only for sio now):
# 0x10 enable console support for this unit. The other console flags
# are ignored unless this is set. Enabling console support does
# not make the unit the preferred console - boot with -h or set
# the 0x20 flag for that. Currently, at most one unit can have
# console support; the first one (in config file order) with
# this flag set is preferred. Setting this flag for sio0 gives
# the old behaviour.
# 0x20 force this unit to be the console (unless there is another
# higher priority console). This replaces the COMCONSOLE option.
# 0x40 reserve this unit for low level console operations. Do not
# access the device in any normal way.
# 0x80 use this port for serial line gdb support in ddb.
#
# PnP `flags' (set via userconfig using pnp x flags y)
# 0x1 disable probing of this device. Used to prevent your modem
# from being attached as a PnP modem.
#
# Options for serial drivers that support consoles (only for sio now):
options BREAK_TO_DEBUGGER #a BREAK on a comconsole goes to
#DDB, if available.
options CONSPEED=9600 #default speed for serial console (default 9600)
# Options for sio:
options COM_ESP #code for Hayes ESP
options COM_MULTIPORT #code for some cards with shared IRQs
# Other flags for sio that aren't documented in the man page.
# 0x20000 enable hardware RTS/CTS and larger FIFOs. Only works for
# ST16650A-compatible UARTs.
#
# Network interfaces: `cx', `ed', `el', `ep', `ie', `is', `le', `lnc'
#
# ar: Arnet SYNC/570i hdlc sync 2/4 port V.35/X.21 serial driver (requires sppp)
# cs: IBM Etherjet and other Crystal Semi CS89x0-based adapters
# cx: Cronyx/Sigma multiport sync/async (with Cisco or PPP framing)
# ed: Western Digital and SMC 80xx; Novell NE1000 and NE2000; 3Com 3C503
# el: 3Com 3C501 (slow!)
# ep: 3Com 3C509
# ex: Intel EtherExpress Pro/10 and other i82595-based adapters
# fe: Fujitsu MB86960A/MB86965A Ethernet
# ie: AT&T StarLAN 10 and EN100; 3Com 3C507; unknown NI5210; Intel EtherExpress
# le: Digital Equipment EtherWorks 2 and EtherWorks 3 (DEPCA, DE100,
# DE101, DE200, DE201, DE202, DE203, DE204, DE205, DE422)
# lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 & Am79C960)
# rdp: RealTek RTL 8002-based pocket ethernet adapters
# sr: RISCom/N2 hdlc sync 1/2 port V.35/X.21 serial driver (requires sppp)
# wl: Lucent Wavelan (ISA card only).
# wi: Lucent WaveLAN/IEEE 802.11 PCMCIA adapters. Note: this supports both
# the PCMCIA and ISA cards: the ISA card is really a PCMCIA to ISA
# bridge with a PCMCIA adapter plugged into it.
# an: Aironet 4500/4800 802.11 wireless adapters. Supports the PCMCIA,
# PCI and ISA varieties.
# xe: Xircom/Intel EtherExpress Pro100/16 PC Card ethernet controller.
# oltr: Olicom ISA token-ring adapters OC-3115, OC-3117, OC-3118 and OC-3133
# (no options needed)
#
device ar0 at isa? port 0x300 irq 10 iomem 0xd0000
device cs0 at isa? port 0x300
device cx0 at isa? port 0x240 irq 15 drq 7
device ed0 at isa? port 0x280 irq 5 iomem 0xd8000
device el0 at isa? port 0x300 irq 9
device ep
device ex
device fe0 at isa? port 0x300
device ie0 at isa? port 0x300 irq 5 iomem 0xd0000
device ie1 at isa? port 0x360 irq 7 iomem 0xd0000
device le0 at isa? port 0x300 irq 5 iomem 0xd0000
device lnc0 at isa? port 0x280 irq 10 drq 0
device rdp0 at isa? port 0x378 irq 7 flags 2
device sr0 at isa? port 0x300 irq 5 iomem 0xd0000
device sn0 at isa? port 0x300 irq 10
device wi
device an
options WLCACHE # enables the signal-strength cache
options WLDEBUG # enables verbose debugging output
device wl0 at isa? port 0x300
device xe0 at isa?
device oltr0 at isa?
#
# ATM related options
#
# The `en' device provides support for Efficient Networks (ENI)
# ENI-155 PCI midway cards, and the Adaptec 155Mbps PCI ATM cards (ANA-59x0).
#
# atm pseudo-device provides generic atm functions and is required for
# atm devices.
# NATM enables the netnatm protocol family that can be used to
# bypass TCP/IP.
#
# the current driver supports only PVC operations (no atm-arp, no multicast).
# for more details, please read the original documents at
# http://www.ccrc.wustl.edu/pub/chuck/tech/bsdatm/bsdatm.html
#
pseudo-device atm
device en
options NATM #native ATM
#
# Audio drivers: `snd', `sb', `pas', `gus', `pca'
#
# snd: Voxware sound support code
# sb: SoundBlaster PCM - SoundBlaster, SB Pro, SB16, ProAudioSpectrum
# sbxvi: SoundBlaster 16
# sbmidi: SoundBlaster 16 MIDI interface
# pas: ProAudioSpectrum PCM and MIDI
# gus: Gravis Ultrasound - Ultrasound, Ultrasound 16, Ultrasound MAX
# gusxvi: Gravis Ultrasound 16-bit PCM (do not use)
# mss: Microsoft Sound System
# css: Crystal Sound System (CSS 423x PnP)
# sscape: Ensoniq Soundscape MIDI interface
# sscape_mss: Ensoniq Soundscape PCM (requires sscape)
# opl: Yamaha OPL-2 and OPL-3 FM - SB, SB Pro, SB 16, ProAudioSpectrum
# uart: stand-alone 6850 UART for MIDI
# mpu: Roland MPU-401 stand-alone card
#
# Note: It has been reported that ISA DMA with the SoundBlaster will
# lock up the machine (PR docs/5358). If this happens to you,
# turning off USWC write posting in your machine's BIOS may fix
# the problem.
#
# Beware! The addresses specified below are also hard-coded in
# src/sys/i386/isa/sound/sound_config.h. If you change the values here, you
# must also change the values in the include file.
#
# pcm: PCM audio through various sound cards.
#
# This has support for a large number of new audio cards, based on
# CS423x, OPTi931, Yamaha OPL-SAx, and also for SB16, GusPnP.
# For more information about this driver and supported cards,
# see the pcm.4 man page.
#
# The flags of the device tells the device a bit more info about the
# device that normally is obtained through the PnP interface.
# bit 2..0 secondary DMA channel;
# bit 4 set if the board uses two dma channels;
# bit 15..8 board type, overrides autodetection; leave it
# zero if don't know what to put in (and you don't,
# since this is unsupported at the moment...).
#
# This driver will use the new PnP code if it's available.
#
# pca: PCM audio through your PC speaker
#
# If you have a GUS-MAX card and want to use the CS4231 codec on the
# card the drqs for the gus max must be 8 bit (1, 2, or 3).
#
# If you would like to use the full duplex option on the gus, then define
# flags to be the ``read dma channel''.
#
# options BROKEN_BUS_CLOCK #PAS-16 isn't working and OPTI chipset
# options SYMPHONY_PAS #PAS-16 isn't working and SYMPHONY chipset
# options EXCLUDE_SBPRO #PAS-16
# options SBC_IRQ=5 #PAS-16. Must match irq on sb0 line.
# PAS16: The order of the pas0/sb0/opl0 is important since the
# sb emulation is enabled in the pas-16 attach.
#
# To override the GUS defaults use:
# options GUS_DMA2
# options GUS_DMA
# options GUS_IRQ
#
# The src/sys/i386/isa/sound/sound.doc has more information.
# Controls all "VOXWARE" driver sound devices. See Luigi's driver
# below for an alternate which may work better for some cards.
#
#device snd
#device pas0 at isa? port 0x388 irq 10 drq 6
#device sb0 at isa? port 0x220 irq 5 drq 1
#device sbxvi0 at isa? drq 5
#device sbmidi0 at isa? port 0x330
#device awe0 at isa? port 0x620
#device gus0 at isa? port 0x220 irq 12 drq 1
##device gus0 at isa? port 0x220 irq 12 drq 1 flags 0x3
#device mss0 at isa? port 0x530 irq 10 drq 1
#device css0 at isa? port 0x534 irq 5 drq 1 flags 0x08
#device sscape0 at isa? port 0x330 irq 9 drq 0
#device trix0 at isa? port 0x330 irq 6 drq 0
#device sscape_mss0 at isa? port 0x534 irq 5 drq 1
#device opl0 at isa? port 0x388
#device mpu0 at isa? port 0x330 irq 6 drq 0
#device uart0 at isa? port 0x330 irq 5
# The newpcm driver (use INSTEAD of snd0 and all VOXWARE drivers!).
# Note that motherboard sound devices may require options PNPBIOS.
#
# Supported cards include:
# Creative SoundBlaster ISA PnP/non-PnP
# Supports ESS and Avance ISA chips as well.
# Gravis UltraSound ISA PnP/non-PnP
# Crystal Semiconductor CS461x/428x PCI
# Neomagic 256AV (ac97)
# Most of the more common ISA/PnP sb/mss/ess compatable cards.
# For non-pnp sound cards with no bridge drivers only:
device pcm0 at isa? irq 10 drq 1 flags 0x0
#
# For PnP/PCI sound cards
device pcm
# The bridge drivers for sound cards. These can be seperately configured
# for providing services to the likes of new-midi (not in the tree yet).
# When used with 'device pcm' they also provide pcm sound services.
#
# sbc: Creative SoundBlaster ISA PnP/non-PnP
# Supports ESS and Avance ISA chips as well.
# gusc: Gravis UltraSound ISA PnP/non-PnP
# csa: Crystal Semiconductor CS461x/428x PCI
# For non-PnP cards:
device sbc0 at isa? port 0x220 irq 5 drq 1 flags 0x15
device gusc0 at isa? port 0x220 irq 5 drq 1 flags 0x13
# Not controlled by `snd'
device pca0 at isa? port IO_TIMER1
#
# Miscellaneous hardware:
#
# mcd: Mitsumi CD-ROM
# scd: Sony CD-ROM
# matcd: Matsushita/Panasonic CD-ROM
# wt: Wangtek and Archive QIC-02/QIC-36 tape drives
# ctx: Cortex-I frame grabber
# apm: Laptop Advanced Power Management (experimental)
# spigot: The Creative Labs Video Spigot video-acquisition board
# meteor: Matrox Meteor video capture board
# bktr: Brooktree bt848/848a/849a/878/879 video capture and TV Tuner board
# cy: Cyclades serial driver
# dgb: Digiboard PC/Xi and PC/Xe series driver (ALPHA QUALITY!)
# dgm: Digiboard PC/Xem driver
# gp: National Instruments AT-GPIB and AT-GPIB/TNT board
# asc: GI1904-based hand scanners, e.g. the Trust Amiscan Grey
# gsc: Genius GS-4500 hand scanner.
# joy: joystick
# labpc: National Instrument's Lab-PC and Lab-PC+
# rc: RISCom/8 multiport card
# rp: Comtrol Rocketport(ISA) - single card
# tw: TW-523 power line interface for use with X-10 home control products
# si: Specialix SI/XIO 4-32 port terminal multiplexor
# stl: Stallion EasyIO and EasyConnection 8/32 (cd1400 based)
# stli: Stallion EasyConnection 8/64, ONboard, Brumby (intelligent)
# Notes on APM
# The flags takes the following meaning for apm0:
# 0x0020 Statclock is broken.
# If apm is omitted, some systems require sysctl -w kern.timecounter.method=1
# for correct timekeeping.
# Notes on the spigot:
# The video spigot is at 0xad6. This port address can not be changed.
# The irq values may only be 10, 11, or 15
# I/O memory is an 8kb region. Possible values are:
# 0a0000, 0a2000, ..., 0fffff, f00000, f02000, ..., ffffff
# The start address must be on an even boundary.
# Add the following option if you want to allow non-root users to be able
# to access the spigot. This option is not secure because it allows users
# direct access to the I/O page.
# options SPIGOT_UNSECURE
# Notes on the Comtrol Rocketport driver:
#
# The exact values used for rp0 depend on how many boards you have
# in the system. The manufacturer's sample configs are listed as:
#
# Comtrol Rocketport ISA single card
# device rp0 at isa? port 0x280
#
# If instead you have two ISA cards, one installed at 0x100 and the
# second installed at 0x180, then you should add the following to
# your kernel configuration file:
#
# device rp0 at isa? port 0x100
# device rp1 at isa? port 0x180
#
# For 4 ISA cards, it might be something like this:
#
# device rp0 at isa? port 0x180
# device rp1 at isa? port 0x100
# device rp2 at isa? port 0x340
# device rp3 at isa? port 0x240
#
# And for PCI cards, you only need say:
#
# device rp
# Notes on the Digiboard driver:
#
# The following flag values have special meanings:
# 0x01 - alternate layout of pins (dgb & dgm)
# 0x02 - use the windowed PC/Xe in 64K mode (dgb only)
# Notes on the Specialix SI/XIO driver:
# **This is NOT a Specialix supported Driver!**
# The host card is memory, not IO mapped.
# The Rev 1 host cards use a 64K chunk, on a 32K boundary.
# The Rev 2 host cards use a 32K chunk, on a 32K boundary.
# The cards can use an IRQ of 11, 12 or 15.
# Notes on the Stallion stl and stli drivers:
# See src/i386/isa/README.stl for complete instructions.
# This is version 0.0.5alpha, unsupported by Stallion.
# The stl driver has a secondary IO port hard coded at 0x280. You need
# to change src/i386/isa/stallion.c if you reconfigure this on the boards.
# The "flags" and "iosiz" settings on the stli driver depend on the board:
# EasyConnection 8/64 ISA: flags 23 iosiz 0x1000
# EasyConnection 8/64 EISA: flags 24 iosiz 0x10000
# EasyConnection 8/64 MCA: flags 25 iosiz 0x1000
# ONboard ISA: flags 4 iosiz 0x10000
# ONboard EISA: flags 7 iosiz 0x10000
# ONboard MCA: flags 3 iosiz 0x10000
# Brumby: flags 2 iosiz 0x4000
# Stallion: flags 1 iosiz 0x10000
device mcd0 at isa? port 0x300 irq 10
# for the Sony CDU31/33A CDROM
device scd0 at isa? port 0x230
# for the SoundBlaster 16 multicd - up to 4 devices
device matcd0 at isa? port 0x230
device wt0 at isa? port 0x300 irq 5 drq 1
device ctx0 at isa? port 0x230 iomem 0xd0000
device spigot0 at isa? port 0xad6 irq 15 iomem 0xee000
device apm0
device gp0 at isa? port 0x2c0
device gsc0 at isa? port IO_GSC1 drq 3
device joy0 at isa? port IO_GAME
device cy0 at isa? irq 10 iomem 0xd4000 iosiz 0x2000
options CY_PCI_FASTINTR # Use with cy_pci unless irq is shared
device dgb0 at isa? port 0x220 iomem 0xfc000
options NDGBPORTS=16 # Defaults to 16*NDGB
device dgm0 at isa? port 0x104 iomem 0xd0000
device labpc0 at isa? port 0x260 irq 5
device rc0 at isa? port 0x220 irq 12
device rp0 at isa? port 0x280
# the port and irq for tw0 are fictitious
device tw0 at isa? port 0x380 irq 11
device si0 at isa? iomem 0xd0000 irq 12
device asc0 at isa? port IO_ASC1 drq 3 irq 10
device stl0 at isa? port 0x2a0 irq 10
device stli0 at isa? port 0x2a0 iomem 0xcc000 flags 23 iosiz 0x1000
# You are unlikely to have the hardware for loran0 <phk@FreeBSD.org>
device loran0 at isa? irq 5
# HOT1 Xilinx 6200 card (http://www.vcc.com/)
device xrpu
#
# MCA devices:
#
# The MCA bus device is `mca'. It provides auto-detection and
# configuration support for all devices on the MCA bus.
#
# The 'aha' device provides support for the Adaptec 1640
#
# The 'bt' device provides support for various Buslogic/Bustek
# and Storage Dimensions SCSI adapters.
#
# The 'ep' device provides support for the 3Com 3C529 ethernet card.
#
device mca
#
# EISA devices:
#
# The EISA bus device is `eisa'. It provides auto-detection and
# configuration support for all devices on the EISA bus.
#
# The `ahb' device provides support for the Adaptec 174X adapter.
#
# The `ahc' device provides support for the Adaptec 274X and 284X
# adapters. The 284X, although a VLB card, responds to EISA probes.
#
# fea: DEC DEFEA EISA FDDI adapter
#
device eisa
device ahb
device ahc
device fea
# The aic7xxx driver will attempt to use memory mapped I/O for all PCI
# controllers that have it configured only if this option is set. Unfortunately,
# this doesn't work on some motherboards, which prevents it from being the
# default.
options AHC_ALLOW_MEMIO
# The adw driver will attempt to use memory mapped I/O for all PCI
# controllers that have it configured only if this option is set.
options ADW_ALLOW_MEMIO
# By default, only 10 EISA slots are probed, since the slot numbers
# above clash with the configuration address space of the PCI subsystem,
# and the EISA probe is not very smart about this. This is sufficient
# for most machines, but in particular the HP NetServer LC series comes
# with an onboard AIC7770 dual-channel SCSI controller on EISA slot #11,
# thus you need to bump this figure to 12 for them.
options EISA_SLOTS=12
#
# PCI devices & PCI options:
#
# The main PCI bus device is `pci'. It provides auto-detection and
# configuration support for all devices on the PCI bus, using either
# configuration mode defined in the PCI specification.
device pci
# PCI options
#
#options PCI_QUIET #quiets PCI code on chipset settings
options COMPAT_OLDPCI #Use PCI shims and glue for old drivers
# The `ahc' device provides support for the Adaptec 29/3940(U)(W)
# and motherboard based AIC7870/AIC7880 adapters.
#
# The `amd' device provides support for the AMD 53C974 SCSI host
# adapter chip as found on devices such as the Tekram DC-390(T).
#
# The `ncr' device provides support for the NCR 53C810 and 53C825
# self-contained SCSI host adapters.
#
# The `isp' device provides support for the Qlogic ISP 1020, 1040
# nd 1040B PCI SCSI host adapters, ISP 1240 Dual Ultra SCSI,
# ISP 1080 and 1280 (Dual) Ultra2, ISP 12160 Ultra3 SCSI, as well as
# the Qlogic ISP 2100 and ISP 2200 Fibre Channel Host Adapters.
#
# The `dc' device provides support for PCI fast ethernet adapters
# based on the DEC/Intel 21143 and various workalikes including:
# the ADMtek AL981 Comet and AN985 Centaur, the ASIX Electronics
# AX88140A and AX88141, the Davicom DM9100 and DM9102, the Lite-On
# 82c168 and 82c169 PNIC, the Lite-On/Macronix LC82C115 PNIC II
# and the Macronix 98713/98713A/98715/98715A/98725 PMAC. This driver
# replaces the old al, ax, dm, pn and mx drivers. List of brands:
# Digital DE500-BA, Kingston KNE100TX, D-Link DFE-570TX, SOHOware SFA110,
# SVEC PN102-TX, CNet Pro110B, 120A, and 120B, Compex RL100-TX,
# LinkSys LNE100TX, LNE100TX V2.0, Jaton XpressNet, Alfa Inc GFC2204,
# KNE110TX.
#
# The `de' device provides support for the Digital Equipment DC21040
# self-contained Ethernet adapter.
#
# The `fxp' device provides support for the Intel EtherExpress Pro/100B
# PCI Fast Ethernet adapters.
#
# The 'rl' device provides support for PCI fast ethernet adapters based
# on the RealTek 8129/8139 chipset. Note that the RealTek driver defaults
# to using programmed I/O to do register accesses because memory mapped
# mode seems to cause severe lockups on SMP hardware. This driver also
# supports the Accton EN1207D `Cheetah' adapter, which uses a chip called
# the MPX 5030/5038, which is either a RealTek in disguise or a RealTek
# workalike. Note that the D-Link DFE-530TX+ uses the RealTek chipset
# and is supported by this driver, not the 'vr' driver.
#
# The 'sf' device provides support for Adaptec Duralink PCI fast
# ethernet adapters based on the Adaptec AIC-6915 "starfire" controller.
# This includes dual and quad port cards, as well as one 100baseFX card.
# Most of these are 64-bit PCI devices, except for one single port
# card which is 32-bit.
#
# The 'ste' device provides support for adapters based on the Sundance
# Technologies ST201 PCI fast ethernet controller. This includes the
# D-Link DFE-550TX.
#
# The 'sis' device provides support for adapters based on the Silicon
# Integrated Systems SiS 900 and SiS 7016 PCI fast ethernet controller
# chips.
#
# The 'sk' device provides support for the SysKonnect SK-984x series
# PCI gigabit ethernet NICs. This includes the SK-9841 and SK-9842
# single port cards (single mode and multimode fiber) and the
# SK-9843 and SK-9844 dual port cards (also single mode and multimode).
# The driver will autodetect the number of ports on the card and
# attach each one as a separate network interface.
#
# The 'ti' device provides support for PCI gigabit ethernet NICs based
# on the Alteon Networks Tigon 1 and Tigon 2 chipsets. This includes the
# Alteon AceNIC, the 3Com 3c985, the Netgear GA620 and various others.
# Note that you will probably want to bump up NMBCLUSTERS a lot to use
# this driver.
#
# The 'tl' device provides support for the Texas Instruments TNETE100
# series 'ThunderLAN' cards and integrated ethernet controllers. This
# includes several Compaq Netelligent 10/100 cards and the built-in
# ethernet controllers in several Compaq Prosignia, Proliant and
# Deskpro systems. It also supports several Olicom 10Mbps and 10/100
# boards.
#
# The `tx' device provides support for the SMC 9432TX cards.
#
# The `vr' device provides support for various fast ethernet adapters
# based on the VIA Technologies VT3043 `Rhine I' and VT86C100A `Rhine II'
# chips, including the D-Link DFE530TX (see 'rl' for DFE530TX+), the Hawking
# Technologies PN102TX, and the AOpen/Acer ALN-320.
#
# The `vx' device provides support for the 3Com 3C590 and 3C595
# early support
#
# The `wb' device provides support for various fast ethernet adapters
# based on the Winbond W89C840F chip. Note: this is not the same as
# the Winbond W89C940F, which is an NE2000 clone.
#
# The `wx' device provides support for the Intel Gigabit Ethernet
# PCI card (`Wiseman').
#
# The `xl' device provides support for the 3Com 3c900, 3c905 and
# 3c905B (Fast) Etherlink XL cards and integrated controllers. This
# includes the integrated 3c905B-TX chips in certain Dell Optiplex and
# Dell Precision desktop machines and the integrated 3c905-TX chips
# in Dell Latitude laptop docking stations.
#
# The `fpa' device provides support for the Digital DEFPA PCI FDDI
# adapter. pseudo-device fddi is also needed.
#
# The `meteor' device is a PCI video capture board. It can also have the
# following options:
# options METEOR_ALLOC_PAGES=xxx preallocate kernel pages for data entry
# figure (ROWS*COLUMN*BYTES_PER_PIXEL*FRAME+PAGE_SIZE-1)/PAGE_SIZE
# options METEOR_DEALLOC_PAGES remove all allocated pages on close(2)
# options METEOR_DEALLOC_ABOVE=xxx remove all allocated pages above the
# specified amount. If this value is below the allocated amount no action
# taken
# options METEOR_SYSTEM_DEFAULT={METEOR_PAL|METEOR_NTSC|METEOR_SECAM}, used
# for initialization of fps routine when a signal is not present.
#
# The 'bktr' device is a PCI video capture device using the Brooktree
# bt848/bt848a/bt849a/bt878/bt879 chipset. When used with a TV Tuner it forms a
# TV card, eg Miro PC/TV, Hauppauge WinCast/TV WinTV, VideoLogic Captivator,
# Intel Smart Video III, AverMedia, IMS Turbo, FlyVideo.
#
# options OVERRIDE_CARD=xxx
# options OVERRIDE_TUNER=xxx
# options OVERRIDE_MSP=1
# options OVERRIDE_DBX=1
# These options can be used to override the auto detection
# The current values for xxx are found in src/sys/dev/bktr/bktr_card.h
# Using sysctl(8) run-time overrides on a per-card basis can be made
#
# options BROOKTREE_SYSTEM_DEFAULT=BROOKTREE_PAL
# or
# options BROOKTREE_SYSTEM_DEFAULT=BROOKTREE_NTSC
# Specifes the default video capture mode.
# This is required for Dual Crystal (28&35Mhz) boards where PAL is used
# to prevent hangs during initialisation. eg VideoLogic Captivator PCI.
#
# options BKTR_USE_PLL
# PAL or SECAM users who have a 28Mhz crystal (and no 35Mhz crystal)
# must enable PLL mode with this option. eg some new Bt878 cards.
#
# options BKTR_GPIO_ACCESS
# This enable IOCTLs which give user level access to the GPIO port.
#
# options BKTR_NO_MSP_RESET
# Prevents the MSP34xx reset. Good if you initialise the MSP in another OS first
#
# options BKTR_430_FX_MODE
# Switch Bt878/879 cards into Intel 430FX chipset compatibility mode.
#
# options BKTR_SIS_VIA_MODE
# Switch Bt878/879 cards into SIS/VIA chipset compatibility mode which is
# needed for some old SiS and VIA chipset motherboards.
# This also allows Bt878/879 chips to work on old OPTi (<1997) chipset
# motherboards and motherboards with bad or incomplete PCI 2.1 support.
# As a rough guess, old = before 1998
#
#
# The oltr driver supports the following Olicom PCI token-ring adapters
# OC-3136, OC-3137, OC-3139, OC-3140, OC-3141, OC-3540, OC-3250
#
device ahc # AHA2940 and onboard AIC7xxx devices
device amd # AMD 53C974 (Teckram DC-390(T))
device isp # Qlogic family
device ncr # NCR/Symbios Logic
device sym # NCR/Symbios Logic (newer chipsets)
#
# Options for ISP
#
# SCSI_ISP_NO_FWLOAD_MASK - mask of isp unit numbers (obviously
# a max of 32) that you wish to disable
# to disable the loading of firmware on.
# SCSI_ISP_NO_NVRAM_MASK - mask of isp unit numbers (obviously
# a max of 32) that you wish to disable
# them picking up information from NVRAM
# (for broken cards you can't fix the NVRAM
# on- very rare, or for systems you can't
# change NVRAM on (e.g. alpha) and you don't
# like what's in there)
# SCSI_ISP_PREFER_MEM_MAP - control preference for using memory mappings
# instead of I/O space mappings. It defaults
# to 1 for i386, 0 for alpha. Set to 1 to
# unconditionally prefer mapping memory,
# else it will use I/O space mappings. Of
# course, this can fail if the PCI implement-
# ation doesn't support what you want.
#
# SCSI_ISP_FCDUPLEX - mask of isp unit numbers (obviously
# a max of 32) that you wish to set fibre
# channel full duplex mode on.
# to disable the loading of firmware on.
# SCSI_ISP_FABRIC enable loading of Fabric f/w flavor (2100).
# SCSI_ISP_SCCLUN enable loading of expanded lun f/w (2100).
# SCSI_ISP_WWN - define a WWN to use as a default
#
# ISP_DISABLE_1020_SUPPORT Disable support for 1020/1040 cards
# ISP_DISABLE_1080_SUPPORT Disable support for 1080/1240 cards
# ISP_DISABLE_12160_SUPPORT Disable support for 12160 cards
# ISP_DISABLE_2100_SUPPORT Disable support for 2100 cards
# (these really just to save some code space)
# (use of all four will cause the kernel to not compile)
#
# ISP_COMPILE_FW - compile all firmware in
# ISP_COMPILE_1020_FW - compile in 1020/1040 firmware
# ISP_COMPILE_1080_FW - compile in 1080/1240/1280 firmware
# ISP_COMPILE_12160_FW - compile in 12160 firmware
# ISP_COMPILE_2100_FW - compile in 2100 firmware
# ISP_COMPILE_2200_FW - compile in 2200 firmware
#
# ISP_TARGET_MODE - enable target mode operation
#
options SCSI_ISP_NO_FWLOAD_MASK=0x12 # disable FW load for isp1, isp4
options SCSI_ISP_NO_NVRAM_MASK=0x1 # disable NVRAM for isp0
options SCSI_ISP_PREFER_MEM_MAP=0 # prefer I/O mapping
options SCSI_ISP_FCDUPLEX=0x4 # isp2 is a Fibre Channel card
# we want in full duplex mode.
options SCSI_ISP_WWN="0x5000000099990000"
#options ISP_DISABLE_1020_SUPPORT
#options ISP_DISABLE_1080_SUPPORT
#options ISP_DISABLE_12160_SUPPORT
#options ISP_DISABLE_2100_SUPPORT
#options ISP_COMPILE_1020_FW=1
#options ISP_COMPILE_1080_FW=1
#options ISP_COMPILE_2100_FW=1
#options ISP_COMPILE_2200_FW=1
#options ISP_TARGET_MODE=1
# Options used in dev/sym/ (Symbios SCSI driver).
#options SYM_SETUP_LP_PROBE_MAP #-Low Priority Probe Map (bits)
# Allows the ncr to take precedence
# 1 (1<<0) -> 810a, 860
# 2 (1<<1) -> 825a, 875, 885, 895
# 4 (1<<2) -> 895a, 896, 1510d
#options SYM_SETUP_SCSI_DIFF #-HVD support for 825a, 875, 885
# disabled:0 (default), enabled:1
#options SYM_SETUP_PCI_PARITY #-PCI parity checking
# disabled:0, enabled:1 (default)
#options SYM_SETUP_MAX_LUN #-Number of LUNs supported
# default:8, range:[1..64]
# MII bus support is required for some PCI 10/100 ethernet NICs,
# namely those which use MII-compliant transceivers or implement
# tranceiver control interfaces that operate like an MII. Adding
# "device miibus0" to the kernel config pulls in support for
# the generic miibus API and all of the PHY drivers, including a
# generic one for PHYs that aren't specifically handled by an
# individual driver.
device miibus
# PCI Ethernet NICs that use the common MII bus controller code.
device dc # DEC/Intel 21143 and various workalikes
device rl # RealTek 8129/8139
device sf # Adaptec AIC-6915 (``Starfire'')
device sis # Silicon Integrated Systems SiS 900/SiS 7016
device ste # Sundance ST201 (D-Link DFE-550TX)
device tl # Texas Instruments ThunderLAN
device vr # VIA Rhine, Rhine II
device wb # Winbond W89C840F
device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
# PCI Ethernet NICs.
device de # DEC/Intel DC21x4x (``Tulip'')
device fxp # Intel EtherExpress PRO/100B (82557, 82558)
device tx # SMC 9432TX (83c170 ``EPIC'')
device vx # 3Com 3c590, 3c595 (``Vortex'')
device sk
device ti
device wx
device fpa
device meteor
#The oltr driver in the ISA section will also find PCI cards.
#device oltr0
# Brooktree driver has been ported to the new I2C framework. Thus,
# you'll need to have the following 3 lines in the kernel config.
# device smbus
# device iicbus
# device iicbb
# The iic and smb devices are only needed if you want to control other
# I2C slaves connected to the external connector of some cards.
#
device bktr
#
# PCCARD/PCMCIA
#
# card: pccard slots
# pcic: isa/pccard bridge
device pcic0 at isa?
device pcic1 at isa?
device card
# You may need to reset all pccards after resuming
options PCIC_RESUME_RESET # reset after resume
#
# Laptop/Notebook options:
#
# See also:
# apm under `Miscellaneous hardware'
# above.
# For older notebooks that signal a powerfail condition (external
# power supply dropped, or battery state low) by issuing an NMI:
options POWERFAIL_NMI # make it beep instead of panicing
#
# SMB bus
#
# System Management Bus support provided by the 'smbus' device.
#
# Supported devices:
# smb standard io
#
# Supported interfaces:
# iicsmb I2C to SMB bridge with any iicbus interface
# bktr brooktree848 I2C hardware interface
# intpm Intel PIIX4 Power Management Unit
# alpm Acer Aladdin-IV/V/Pro2 Power Management Unit
#
device smbus # Bus support, required for smb below.
device intpm
device alpm
device smb
#
# I2C Bus
#
# Philips i2c bus support is provided by the `iicbus' device.
#
# Supported devices:
# ic i2c network interface
# iic i2c standard io
# iicsmb i2c to smb bridge. Allow i2c i/o with smb commands.
#
# Supported interfaces:
# pcf Philips PCF8584 ISA-bus controller
# bktr brooktree848 I2C software interface
#
# Other:
# iicbb generic I2C bit-banging code (needed by lpbb, bktr)
#
device iicbus # Bus support, required for ic/iic/iicsmb below.
device iicbb
device ic
device iic
device iicsmb # smb over i2c bridge
device pcf0 at isa? port 0x320 irq 5
# ISDN4BSD section
#
# See /usr/share/examples/isdn/ROADMAP for an introduction to isdn4bsd.
#
# i4b passive ISDN cards support (isic - I4b Siemens Isdn Chipset driver)
# note that the ``options'' and ``device'' lines must BOTH be defined !
#
# Driver entries marked "(not supported yet!)" are not working currently
# due to not being converted to newbus. We hope to get them back to support
# in the near future.
#
# ISA bus non-PnP Cards:
# ----------------------
#
# Teles S0/8 or Niccy 1008
options TEL_S0_8
device isic0 at isa? iomem 0xd0000 irq 5 flags 1
#
# Teles S0/16 or Creatix ISDN-S0 or Niccy 1016
options TEL_S0_16
#device isic0 at isa? port 0xd80 iomem 0xd0000 irq 5 flags 2
#
# Teles S0/16.3
options TEL_S0_16_3
#device isic0 at isa? port 0xd80 irq 5 flags 3
#
# AVM A1 or AVM Fritz!Card
options AVM_A1
#device isic0 at isa? port 0x340 irq 5 flags 4
#
# USRobotics Sportster ISDN TA intern (not supported yet!)
#options USR_STI
#device isic0 at isa? port 0x268 irq 5 flags 7
#
# ITK ix1 Micro ( < V.3, non-PnP version ) (not supported yet!)
#options ITKIX1
#device isic0 at isa? port 0x398 irq 10 flags 18
#
# ELSA PCC-16
options ELSA_PCC16
#device isic0 at isa? port 0x360 irq 10 flags 20
#
# ISA bus PnP Cards:
# ------------------
#
# Teles S0/16.3 PnP
options TEL_S0_16_3_P
#device isic
#
# Creatix ISDN-S0 P&P
options CRTX_S0_P
#device isic
#
# Dr. Neuhaus Niccy Go@
options DRN_NGO
#device isic
#
# Sedlbauer Win Speed
options SEDLBAUER
#device isic
#
# Dynalink IS64PH (not supported yet!)
#options DYNALINK
#device isic
#
# ELSA QuickStep 1000pro ISA
options ELSA_QS1ISA
#device isic
#
# ITK ix1 Micro ( V.3, PnP version ) (not supported yet!)
#options ITKIX1
#device isic
#
# AVM Fritz!Card PnP (not supported yet!)
#options AVM_PNP
#device isic
#
# Siemens I-Surf 2.0
options SIEMENS_ISURF2
#device isic
#
# Asuscom ISDNlink 128K ISAC - broken
#options ASUSCOM_IPAC
#device isic
#
# PCI bus Cards:
# --------------
#
# ELSA MicroLink ISDN/PCI (same as ELSA QuickStep 1000pro PCI)
options ELSA_QS1PCI
#device isic
#
# AVM Fritz!Card PCI
options AVM_A1_PCI
#device isic
#
# PCMCIA Cards:
# -------------
#
# AVM PCMCIA Fritz!Card (not supported yet!)
#options AVM_A1_PCMCIA
#device isic0 at isa? port 0x340 irq 5 flags 10
#
# Active Cards:
# -------------
#
# Stollmann Tina-dd control device
# (driver under development, not fully functional!)
device tina0 at isa? port 0x260 irq 10
#
# ISDN Protocol Stack
# -------------------
#
# Q.921 / layer 2 - i4b passive cards D channel handling
pseudo-device "i4bq921"
#
# Q.931 / layer 3 - i4b passive cards D channel handling
pseudo-device "i4bq931"
#
# layer 4 - i4b common passive and active card handling
pseudo-device "i4b"
#
# ISDN devices
# ------------
#
# userland driver to do ISDN tracing (for passive cards only)
pseudo-device "i4btrc" 4
#
# userland driver to control the whole thing
pseudo-device "i4bctl"
#
# userland driver for access to raw B channel
pseudo-device "i4brbch" 4
#
# userland driver for telephony
pseudo-device "i4btel" 2
#
# network driver for IP over raw HDLC ISDN
pseudo-device "i4bipr" 4
# enable VJ header compression detection for ipr i/f
options IPR_VJ
# enable logging of the first n IP packets to isdnd (n=32 here)
#options IPR_LOG=32
#
# network driver for sync PPP over ISDN
pseudo-device "i4bisppp" 4
# Parallel-Port Bus
#
# Parallel port bus support is provided by the `ppbus' device.
# Multiple devices may be attached to the parallel port, devices
# are automatically probed and attached when found.
#
# Supported devices:
# vpo Iomega Zip Drive
# Requires SCSI disk support ('scbus' and 'da'), best
# performance is achieved with ports in EPP 1.9 mode.
# lpt Parallel Printer
# plip Parallel network interface
# ppi General-purpose I/O ("Geek Port") + IEEE1284 I/O
# pps Pulse per second Timing Interface
# lpbb Philips official parallel port I2C bit-banging interface
#
# Supported interfaces:
# ppc ISA-bus parallel port interfaces.
#
options PPC_PROBE_CHIPSET # Enable chipset specific detection
# (see flags in ppc(4))
options DEBUG_1284 # IEEE1284 signaling protocol debug
options PERIPH_1284 # Makes your computer act as a IEEE1284
# compliant peripheral
options DONTPROBE_1284 # Avoid boot detection of PnP parallel devices
options VP0_DEBUG # ZIP/ZIP+ debug
options LPT_DEBUG # Printer driver debug
options PPC_DEBUG # Parallel chipset level debug
options PLIP_DEBUG # Parallel network IP interface debug
options PCFCLOCK_VERBOSE # Verbose pcfclock driver
options PCFCLOCK_MAX_RETRIES=5 # Maximum read tries (default 10)
device ppc0 at isa? irq 7
device ppbus
device vpo
device lpt
device plip
device ppi
device pps
device lpbb
device pcfclock
# Kernel BOOTP support
options BOOTP # Use BOOTP to obtain IP address/hostname
options BOOTP_NFSROOT # NFS mount root filesystem using BOOTP info
options BOOTP_NFSV3 # Use NFS v3 to NFS mount root
options BOOTP_COMPAT # Workaround for broken bootp daemons.
options BOOTP_WIRED_TO=fxp0 # Use interface fxp0 for BOOTP
#
# Add tie-ins for a hardware watchdog. This only enable the hooks;
# the user must still supply the actual driver.
#
options HW_WDOG
#
# Set the number of PV entries per process. Increasing this can
# stop panics related to heavy use of shared memory. However, that can
# (combined with large amounts of physical memory) cause panics at
# boot time due the kernel running out of VM space.
#
# If you're tweaking this, you might also want to increase the sysctls
# "vm.v_free_min", "vm.v_free_reserved", and "vm.v_free_target".
#
# The value below is the one more than the default.
#
options PMAP_SHPGPERPROC=201
#
# Disable swapping. This option removes all code which actually performs
# swapping, so it's not possible to turn it back on at run-time.
#
# This is sometimes usable for systems which don't have any swap space
# (see also sysctls "vm.defer_swapspace_pageouts" and
# "vm.disable_swapspace_pageouts")
#
#options NO_SWAPPING
# Set the number of sf_bufs to allocate. sf_bufs are virtual buffers
# for sendfile(2) that are used to map file VM pages, and normally
# default to a quantity that is roughly 16*MAXUSERS+512. You would
# typically want about 4 of these for each simultaneous file send.
#
options NSFBUFS=1024
#
# Enable extra debugging code for locks. This stores the filename and
# line of whatever acquired the lock in the lock itself, and change a
# number of function calls to pass around the relevant data. This is
# not at all useful unless you are debugging lock code. Also note
# that it is likely to break e.g. fstat(1) unless you recompile your
# userland with -DDEBUG_LOCKS as well.
#
options DEBUG_LOCKS
#
# SysVR4 ABI emulation
#
# The svr4 ABI emulator can be statically compiled into the kernel or loaded as
# a KLD module.
# The STREAMS network emulation code can also be compiled statically or as a
# module. If loaded as a module, it must be loaded before the svr4 module
# (the /usr/sbin/svr4 script does this for you). If compiling statically,
# the `streams' pseudo-device must be configured into any kernel which also
# specifies COMPAT_SVR4. It is possible to have a statically-configured
# STREAMS device and a dynamically loadable svr4 emulator; the /usr/sbin/svr4
# script understands that it doesn't need to load the `streams' module under
# those circumstances.
# Caveat: At this time, `options KTRACE' is required for the svr4 emulator
# (whether static or dynamic).
#
options COMPAT_SVR4 # build emulator statically
options DEBUG_SVR4 # enable verbose debugging
pseudo-device streams # STREAMS network driver (required for svr4).
# The 'dpt' driver provides support for DPT controllers (http://www.dpt.com/).
# These have hardware RAID-{0,1,5} support, and do multi-initiator I/O.
# The DPT controllers are commonly re-licensed under other brand-names -
# some controllers by Olivetti, Dec, HP, AT&T, SNI, AST, Alphatronic, NEC and
# Compaq are actually DPT controllers.
#
# See src/sys/dev/dpt for debugging and other subtle options.
# DPT_MEASURE_PERFORMANCE Enables a set of (semi)invasive metrics. Various
# instruments are enabled. The tools in
# /usr/sbin/dpt_* assume these to be enabled.
# DPT_HANDLE_TIMEOUTS Normally device timeouts are handled by the DPT.
# If you ant the driver to handle timeouts, enable
# this option. If your system is very busy, this
# option will create more trouble than solve.
# DPT_TIMEOUT_FACTOR Used to compute the excessive amount of time to
# wait when timing out with the above option.
# DPT_DEBUG_xxxx These are controllable from sys/dev/dpt/dpt.h
# DPT_LOST_IRQ When enabled, will try, once per second, to catch
# any interrupt that got lost. Seems to help in some
# DPT-firmware/Motherboard combinations. Minimal
# cost, great benefit.
# DPT_RESET_HBA Make "reset" actually reset the controller
# instead of fudging it. Only enable this if you
# are 100% certain you need it.
device dpt
# DPT options
#!CAM# options DPT_MEASURE_PERFORMANCE
#!CAM# options DPT_HANDLE_TIMEOUTS
options DPT_TIMEOUT_FACTOR=4
options DPT_LOST_IRQ
options DPT_RESET_HBA
options DPT_ALLOW_MEMIO
# USB support
# UHCI controller
device uhci
# OHCI controller
device ohci
# General USB code (mandatory for USB)
device usb
#
# Generic USB device driver
device ugen
# Human Interface Device (anything with buttons and dials)
device uhid
# USB keyboard
device ukbd
# USB printer
device ulpt
# USB Iomega Zip 100 Drive
device umass
# USB mouse
device ums
# Diamond Rio 500 Mp3 player
device urio
#
# ADMtek USB ethernet. Supports the LinkSys USB100TX,
# the Billionton USB100, the Melco LU-ATX, the D-Link DSB-650TX
# and the SMC 2202USB. Also works with the ADMtek AN986 Pegasus
# eval board.
device aue
#
# CATC USB-EL1201A USB ethernet. Supports the CATC Netmate
# and Netmate II, and the Belkin F5U111.
device cue
#
# Kawasaki LSI ethernet. Supports the LinkSys USB10T,
# Entrega USB-NET-E45, Peracom Ethernet Adapter, the
# 3Com 3c19250, the ADS Technologies USB-10BT, the ATen UC10T,
# the Netgear EA101, the D-Link DSB-650, the SMC 2102USB
# and 2104USB, and the Corega USB-T.
device kue
# debugging options for the USB subsystem
#
options UHCI_DEBUG
options OHCI_DEBUG
options USB_DEBUG
options UGEN_DEBUG
options UHID_DEBUG
options UHUB_DEBUG
options UKBD_DEBUG
options ULPT_DEBUG
options UMASS_DEBUG
options UMS_DEBUG
options URIO_DEBUG
# options for ukbd:
options UKBD_DFLT_KEYMAP # specify the built-in keymap
makeoptions UKBD_DFLT_KEYMAP=it.iso
#
# Embedded system options:
#
# An embedded system might want to run something other than init.
options INIT_PATH="/sbin/init:/stand/sysinstall"
# Debug options
options BUS_DEBUG # enable newbus debugging
options DEBUG_VFS_LOCKS # enable vfs lock debugging
options NPX_DEBUG # enable npx debugging (FPU/math emu)
# More undocumented options for linting.
# Note that documenting these are not considered an affront.
options AHC_DUMP_EEPROM
options AHC_TMODE_ENABLE
options CAM_DEBUG_DELAY
options CLK_CALIBRATION_LOOP
options CLK_USE_I8254_CALIBRATION
options CLK_USE_TSC_CALIBRATION
options CLUSTERDEBUG
options COMPAT_LINUX
options CPU_UPGRADE_HW_CACHE
options DEBUG
options DEBUG_LINUX
#options DISABLE_PSE
options ENABLE_ALART
options ENABLE_VFS_IOOPT
options FB_DEBUG
options FB_INSTALL_CDEV
options FE_8BIT_SUPPORT
options I4B_SMP_WORKAROUND
options I586_PMC_GUPROF=0x70000
options IBCS2
options KBDIO_DEBUG=2
options KBD_MAXRETRY=4
options KBD_MAXWAIT=6
options KBD_RESETDELAY=201
options KEY
options LOCKF_DEBUG
options LOUTB
options MSGMNB=2049
options MSGMNI=41
options MSGSEG=2049
options MSGSSZ=16
options MSGTQL=41
options NBUF=512
options NETATALKDEBUG
options NMBCLUSTERS=1024
#options OLTR_NO_BULLSEYE_MAC
#options OLTR_NO_HAWKEYE_MAC
#options OLTR_NO_TMS_MAC
options PANIC_REBOOT_WAIT_TIME=16
options PNPBIOS
options PSM_DEBUG=1
options SCSI_NCR_DEBUG
options SCSI_NCR_MAX_SYNC=10000
options SCSI_NCR_MAX_WIDE=1
options SCSI_NCR_MYADDR=7
options SC_DEBUG_LEVEL
options SC_RENDER_DEBUG
options SEMMAP=31
options SEMMNI=11
options SEMMNS=61
options SEMMNU=31
options SEMMSL=61
options SEMOPM=101
options SEMUME=11
options SHMALL=1025
options SHMMAX="(SHMMAXPGS*PAGE_SIZE+1)"
options SHMMAXPGS=1025
options SHMMIN=2
options SHMMNI=33
options SHMSEG=9
options SHOW_BUSYBUFS # List buffers that prevent root unmount
options SIMPLELOCK_DEBUG
options SI_DEBUG
options SLIP_IFF_OPTS
options SPX_HACK
options TIMER_FREQ="((14318182+6)/12)"
options VFS_BIO_DEBUG
options VM_KMEM_SIZE
options VM_KMEM_SIZE_MAX
options VM_KMEM_SIZE_SCALE
Reference in New Issue View Git Blame Copy Permalink