mirror of
https://git.FreeBSD.org/src.git
synced 2024-12-20 11:11:24 +00:00
Mirror of the FreeBSD src repository https://git.FreeBSD.org/src.git .
a157e42516
The main goal of this is to generate timer interrupts only when there is some work to do. When CPU is busy interrupts are generating at full rate of hz + stathz to fullfill scheduler and timekeeping requirements. But when CPU is idle, only minimum set of interrupts (down to 8 interrupts per second per CPU now), needed to handle scheduled callouts is executed. This allows significantly increase idle CPU sleep time, increasing effect of static power-saving technologies. Also it should reduce host CPU load on virtualized systems, when guest system is idle. There is set of tunables, also available as writable sysctls, allowing to control wanted event timer subsystem behavior: kern.eventtimer.timer - allows to choose event timer hardware to use. On x86 there is up to 4 different kinds of timers. Depending on whether chosen timer is per-CPU, behavior of other options slightly differs. kern.eventtimer.periodic - allows to choose periodic and one-shot operation mode. In periodic mode, current timer hardware taken as the only source of time for time events. This mode is quite alike to previous kernel behavior. One-shot mode instead uses currently selected time counter hardware to schedule all needed events one by one and program timer to generate interrupt exactly in specified time. Default value depends of chosen timer capabilities, but one-shot mode is preferred, until other is forced by user or hardware. kern.eventtimer.singlemul - in periodic mode specifies how much times higher timer frequency should be, to not strictly alias hardclock() and statclock() events. Default values are 2 and 4, but could be reduced to 1 if extra interrupts are unwanted. kern.eventtimer.idletick - makes each CPU to receive every timer interrupt independently of whether they busy or not. By default this options is disabled. If chosen timer is per-CPU and runs in periodic mode, this option has no effect - all interrupts are generating. As soon as this patch modifies cpu_idle() on some platforms, I have also refactored one on x86. Now it makes use of MONITOR/MWAIT instrunctions (if supported) under high sleep/wakeup rate, as fast alternative to other methods. It allows SMP scheduler to wake up sleeping CPUs much faster without using IPI, significantly increasing performance on some highly task-switching loads. Tested by: many (on i386, amd64, sparc64 and powerc) H/W donated by: Gheorghe Ardelean Sponsored by: iXsystems, Inc. |
||
|---|---|---|
| bin | ||
| cddl | ||
| contrib | ||
| crypto | ||
| etc | ||
| games | ||
| gnu | ||
| include | ||
| kerberos5 | ||
| lib | ||
| libexec | ||
| release | ||
| rescue | ||
| sbin | ||
| secure | ||
| share | ||
| sys | ||
| tools | ||
| usr.bin | ||
| usr.sbin | ||
| COPYRIGHT | ||
| LOCKS | ||
| MAINTAINERS | ||
| Makefile | ||
| Makefile.inc1 | ||
| Makefile.mips | ||
| ObsoleteFiles.inc | ||
| README | ||
| UPDATING | ||
This is the top level of the FreeBSD source directory. This file was last revised on: $FreeBSD$ For copyright information, please see the file COPYRIGHT in this directory (additional copyright information also exists for some sources in this tree - please see the specific source directories for more information). The Makefile in this directory supports a number of targets for building components (or all) of the FreeBSD source tree, the most commonly used one being ``world'', which rebuilds and installs everything in the FreeBSD system from the source tree except the kernel, the kernel-modules and the contents of /etc. The ``world'' target should only be used in cases where the source tree has not changed from the currently running version. See: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/makeworld.html for more information, including setting make(1) variables. The ``buildkernel'' and ``installkernel'' targets build and install the kernel and the modules (see below). Please see the top of the Makefile in this directory for more information on the standard build targets and compile-time flags. Building a kernel is a somewhat more involved process, documentation for which can be found at: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig.html And in the config(8) man page. Note: If you want to build and install the kernel with the ``buildkernel'' and ``installkernel'' targets, you might need to build world before. More information is available in the handbook. The sample kernel configuration files reside in the sys/<arch>/conf sub-directory (assuming that you've installed the kernel sources), the file named GENERIC being the one used to build your initial installation kernel. The file NOTES contains entries and documentation for all possible devices, not just those commonly used. It is the successor of the ancient LINT file, but in contrast to LINT, it is not buildable as a kernel but a pure reference and documentation file. Source Roadmap: --------------- bin System/user commands. contrib Packages contributed by 3rd parties. crypto Cryptography stuff (see crypto/README). etc Template files for /etc. games Amusements. gnu Various commands and libraries under the GNU Public License. Please see gnu/COPYING* for more information. include System include files. kerberos5 Kerberos5 (Heimdal) package. lib System libraries. libexec System daemons. release Release building Makefile & associated tools. rescue Build system for statically linked /rescue utilities. sbin System commands. secure Cryptographic libraries and commands. share Shared resources. sys Kernel sources. tools Utilities for regression testing and miscellaneous tasks. usr.bin User commands. usr.sbin System administration commands. For information on synchronizing your source tree with one or more of the FreeBSD Project's development branches, please see: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/synching.html