mirror of
https://git.FreeBSD.org/src.git
synced 2024-12-27 11:55:06 +00:00
143 lines
4.8 KiB
C
143 lines
4.8 KiB
C
/*-
|
|
* Copyright (c) 2012 M. Warner Losh. All Rights Reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY AUTHOR AND CONTRIBUTORS ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL AUTHOR OR CONTRIBUTORS BE LIABLE
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*/
|
|
|
|
#include <sys/cdefs.h>
|
|
__FBSDID("$FreeBSD$");
|
|
|
|
#include <sys/param.h>
|
|
#include <sys/systm.h>
|
|
#include <sys/bus.h>
|
|
#include <sys/kernel.h>
|
|
#include <sys/malloc.h>
|
|
#include <sys/module.h>
|
|
|
|
#define _ARM32_BUS_DMA_PRIVATE
|
|
#include <machine/bus.h>
|
|
|
|
#include <arm/at91/at91var.h>
|
|
#include <arm/at91/at91board.h>
|
|
#include <arm/at91/at91rm92reg.h>
|
|
#include <arm/at91/at91rm9200var.h>
|
|
#include <arm/at91/at91_pioreg.h>
|
|
#include <arm/at91/at91_piovar.h>
|
|
|
|
/*
|
|
* The AT91RM9200 uses the same silicon for both the BGA and PQFP
|
|
* packages. There's no documented way to detect this at runtime,
|
|
* so we require the board code to register what type of SoC is on the
|
|
* board in question. The pinouts are not quite compatible, and we
|
|
* use this information to cope with the slight differences.
|
|
*/
|
|
void
|
|
at91rm9200_set_subtype(enum at91_soc_subtype st)
|
|
{
|
|
|
|
switch (st) {
|
|
case AT91_ST_RM9200_BGA:
|
|
case AT91_ST_RM9200_PQFP:
|
|
soc_info.subtype = st;
|
|
break;
|
|
default:
|
|
panic("Bad SoC subtype %d for at91rm9200_set_subtype.", st);
|
|
break;
|
|
}
|
|
}
|
|
|
|
void
|
|
at91rm9200_config_uart(unsigned devid, unsigned unit, unsigned pinmask)
|
|
{
|
|
|
|
/*
|
|
* Since the USART supports RS-485 multidrop mode, it allows the
|
|
* TX pins to float. However, for RS-232 operations, we don't want
|
|
* these pins to float. Instead, they should be pulled up to avoid
|
|
* mismatches. Linux does something similar when it configures the
|
|
* TX lines. This implies that we also allow the RX lines to float
|
|
* rather than be in the state they are left in by the boot loader.
|
|
* Since they are input pins, I think that this is the right thing
|
|
* to do.
|
|
*/
|
|
|
|
/*
|
|
* Current boards supported don't need the extras, but they should be
|
|
* implemented. But that should wait until the new pin api goes in.
|
|
*/
|
|
switch (devid) {
|
|
case AT91_ID_DBGU:
|
|
at91_pio_use_periph_a(AT91RM92_PIOA_BASE, AT91C_PIO_PA30, 0); /* DRXD */
|
|
at91_pio_use_periph_a(AT91RM92_PIOA_BASE, AT91C_PIO_PA31, 1); /* DTXD */
|
|
break;
|
|
|
|
case AT91RM9200_ID_USART0:
|
|
at91_pio_use_periph_a(AT91RM92_PIOA_BASE, AT91C_PIO_PA17, 1); /* TXD0 */
|
|
at91_pio_use_periph_a(AT91RM92_PIOA_BASE, AT91C_PIO_PA18, 0); /* RXD0 */
|
|
/* CTS PA20 */
|
|
/* RTS -- errata #39 PA21 */
|
|
break;
|
|
|
|
case AT91RM9200_ID_USART1:
|
|
at91_pio_use_periph_a(AT91RM92_PIOB_BASE, AT91C_PIO_PB20, 1); /* TXD1 */
|
|
at91_pio_use_periph_a(AT91RM92_PIOB_BASE, AT91C_PIO_PB21, 0); /* RXD1 */
|
|
/* RI - PB18 */
|
|
/* DTR - PB19 */
|
|
/* DCD - PB23 */
|
|
/* CTS - PB24 */
|
|
/* DSR - PB25 */
|
|
/* RTS - PB26 */
|
|
break;
|
|
|
|
case AT91RM9200_ID_USART2:
|
|
at91_pio_use_periph_a(AT91RM92_PIOA_BASE, AT91C_PIO_PA22, 0); /* RXD2 */
|
|
at91_pio_use_periph_a(AT91RM92_PIOA_BASE, AT91C_PIO_PA23, 1); /* TXD2 */
|
|
/* CTS - PA30 B periph */
|
|
/* RTS - PA31 B periph */
|
|
break;
|
|
|
|
case AT91RM9200_ID_USART3:
|
|
at91_pio_use_periph_b(AT91RM92_PIOA_BASE, AT91C_PIO_PA5, 1); /* TXD3 */
|
|
at91_pio_use_periph_b(AT91RM92_PIOA_BASE, AT91C_PIO_PA6, 0); /* RXD3 */
|
|
/* CTS - PB0 B periph */
|
|
/* RTS - PB1 B periph */
|
|
break;
|
|
|
|
default:
|
|
break;
|
|
}
|
|
}
|
|
|
|
void
|
|
at91rm9200_config_mci(int has_4wire)
|
|
{
|
|
/* XXX TODO chip changed GPIO, other slots, etc */
|
|
at91_pio_use_periph_a(AT91RM92_PIOA_BASE, AT91C_PIO_PA27, 0); /* MCCK */
|
|
at91_pio_use_periph_a(AT91RM92_PIOA_BASE, AT91C_PIO_PA28, 1); /* MCCDA */
|
|
at91_pio_use_periph_a(AT91RM92_PIOA_BASE, AT91C_PIO_PA29, 1); /* MCDA0 */
|
|
if (has_4wire) {
|
|
at91_pio_use_periph_b(AT91RM92_PIOB_BASE, AT91C_PIO_PB3, 1); /* MCDA1 */
|
|
at91_pio_use_periph_b(AT91RM92_PIOB_BASE, AT91C_PIO_PB4, 1); /* MCDA2 */
|
|
at91_pio_use_periph_b(AT91RM92_PIOB_BASE, AT91C_PIO_PB5, 1); /* MCDA3 */
|
|
}
|
|
}
|