freebsd/share/man/man4/wb.4

.\" Copyright (c) 1997, 1998
.\"	Bill Paul <wpaul@ctr.columbia.edu>. All rights reserved.
.\"
.\" Redistribution and use in source and binary forms, with or without
.\" modification, are permitted provided that the following conditions
.\" are met:
.\" 1. Redistributions of source code must retain the above copyright
.\"    notice, this list of conditions and the following disclaimer.
.\" 2. Redistributions in binary form must reproduce the above copyright
.\"    notice, this list of conditions and the following disclaimer in the
.\"    documentation and/or other materials provided with the distribution.
.\" 3. All advertising materials mentioning features or use of this software
.\"    must display the following acknowledgement:
.\"	This product includes software developed by Bill Paul.
.\" 4. Neither the name of the author nor the names of any co-contributors
.\"    may be used to endorse or promote products derived from this software
.\"   without specific prior written permission.
.\"
.\" THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND
.\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
.\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
.\" ARE DISCLAIMED.  IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD
.\" BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
.\" CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
.\" SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
.\" INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
.\" CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
.\" ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
.\" THE POSSIBILITY OF SUCH DAMAGE.
.\"
.\" $FreeBSD$
.\"
.Dd July 16, 2005
.Dt WB 4
.Os
.Sh NAME
.Nm wb
.Nd "Winbond W89C840F Fast Ethernet device driver"
.Sh SYNOPSIS
To compile this driver into the kernel,
place the following lines in your
kernel configuration file:
.Bd -ragged -offset indent
.Cd "device miibus"
.Cd "device wb"
.Ed
.Pp
Alternatively, to load the driver as a
module at boot time, place the following line in
.Xr loader.conf 5 :
.Bd -literal -offset indent
if_wb_load="YES"
.Ed
.Sh DESCRIPTION
The
.Nm
driver provides support for PCI Ethernet adapters and embedded
controllers based on the Winbond W89C840F Fast Ethernet controller
chip.
The 840F should not be confused with the 940F, which is
an NE2000 clone and only supports 10Mbps speeds.
.Pp
The Winbond controller uses bus master DMA and is designed to be
a DEC 'tulip' workalike.
It differs from the standard DEC design
in several ways: the control and status registers are spaced 4
bytes apart instead of 8, and the receive filter is programmed through
registers rather than by downloading a special setup frame via
the transmit DMA engine.
Using an external PHY, the Winbond chip
supports both 10 and 100Mbps speeds in either full or half duplex.
.Pp
The
.Nm
driver supports the following media types:
.Pp
.Bl -tag -width xxxxxxxxxxxxxxxxxxxx
.It autoselect
Enable autoselection of the media type and options.
This is only
supported if the PHY chip attached to the Winbond controller
supports NWAY autonegotiation.
The user can manually override
the autoselected mode by adding media options to the
.Pa /etc/rc.conf
file.
.It 10baseT/UTP
Set 10Mbps operation.
The
.Ar mediaopt
option can also be used to select either
.Ar full-duplex
or
.Ar half-duplex
modes.
.It 100baseTX
Set 100Mbps (Fast Ethernet) operation.
The
.Ar mediaopt
option can also be used to select either
.Ar full-duplex
or
.Ar half-duplex
modes.
.El
.Pp
The
.Nm
driver supports the following media options:
.Pp
.Bl -tag -width xxxxxxxxxxxxxxxxxxxx
.It full-duplex
Force full duplex operation
.It half-duplex
Force half duplex operation.
.El
.Pp
Note that the 100baseTX media type is only available if supported
by the adapter.
For more information on configuring this device, see
.Xr ifconfig 8 .
.Sh HARDWARE
The
.Nm
driver supports Winbond W89C840F based Fast Ethernet
adapters and embedded controllers including:
.Pp
.Bl -bullet -compact
.It
Trendware TE100-PCIE
.El
.Sh DIAGNOSTICS
.Bl -diag
.It "wb%d: couldn't map memory"
A fatal initialization error has occurred.
.It "wb%d: couldn't map interrupt"
A fatal initialization error has occurred.
.It "wb%d: watchdog timeout"
The device has stopped responding to the network, or there is a problem with
the network connection (cable).
.It "wb%d: no memory for rx list"
The driver failed to allocate an mbuf for the receiver ring.
.It "wb%d: no memory for tx list"
The driver failed to allocate an mbuf for the transmitter ring when
allocating a pad buffer or collapsing an mbuf chain into a cluster.
.It "wb%d: chip is in D3 power state -- setting to D0"
This message applies only to adapters which support power
management.
Some operating systems place the controller in low power
mode when shutting down, and some PCI BIOSes fail to bring the chip
out of this state before configuring it.
The controller loses all of
its PCI configuration in the D3 state, so if the BIOS does not set
it back to full power mode in time, it will not be able to configure it
correctly.
The driver tries to detect this condition and bring
the adapter back to the D0 (full power) state, but this may not be
enough to return the driver to a fully operational condition.
If
you see this message at boot time and the driver fails to attach
the device as a network interface, you will have to perform second
warm boot to have the device properly configured.
.Pp
Note that this condition only occurs when warm booting from another
operating system.
If you power down your system prior to booting
.Fx ,
the card should be configured correctly.
.El
.Sh SEE ALSO
.Xr arp 4 ,
.Xr miibus 4 ,
.Xr netintro 4 ,
.Xr ng_ether 4 ,
.Xr ifconfig 8
.Sh HISTORY
The
.Nm
device driver first appeared in
.Fx 3.0 .
.Sh AUTHORS
The
.Nm
driver was written by
.An Bill Paul Aq wpaul@ctr.columbia.edu .
.Sh BUGS
The Winbond chip seems to behave strangely in some cases when the
link partner switches modes.
If for example both sides are set to
10Mbps half-duplex, and the other end is changed to 100Mbps
full-duplex, the Winbond's receiver suddenly starts writing trash
all over the RX descriptors.
The
.Nm
driver handles this by forcing a reset of both the controller
chip and attached PHY.
This is drastic, but it appears to be the
only way to recover properly from this condition.