mirror/freebsd
1
0
Fork 0
mirror of https://git.FreeBSD.org/src.git synced 2024-12-29 12:03:03 +00:00
Code Issues Releases Activity
c7a64a0369
freebsd/sys/i386/isa/ft.c
Poul-Henning Kamp 87eafbcacd Moved the ft.c from 1.1.5.1 over. It works on my Conner thingie. Got 
rid of a ton of unused vars at the same time.
1994-09-25 06:04:25 +00:00

2551 lines
61 KiB
C
Raw Blame History

/*
* Copyright (c) 1993, 1994 Steve Gerakines
*
* This is freely redistributable software. You may do anything you
* wish with it, so long as the above notice stays intact.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR(S) ``AS IS'' AND ANY EXPRESS
* OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE AUTHOR(S) BE LIABLE FOR ANY DIRECT,
* INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
* IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
* ft.c - QIC-40/80 floppy tape driver
* $Id: ft.c,v 1.7 1994/06/22 05:52:36 jkh Exp $
*
* 06/07/94 v0.9 ++sg
* Tape stuck on segment problem should be gone. Re-wrote buffering
* scheme. Added support for drives that do not automatically perform
* seek load point. Can handle more wakeup types now and should correctly
* report most manufacturer names. Fixed places where unit 0 was being
* sent to the fdc instead of the actual unit number. Added ioctl support
* for an in-core badmap.
*
* 01/26/94 v0.3b - Jim Babb
* Got rid of the hard coded device selection. Moved (some of) the
* static variables into a structure for support of multiple devices.
* ( still has a way to go for 2 controllers - but closer )
* Changed the interface with fd.c so we no longer 'steal' it's
* driver routine vectors.
*
* 10/30/93 v0.3
* Fixed a couple more bugs. Reading was sometimes looping when an
* an error such as address-mark-missing was encountered. Both
* reading and writing was having more backup-and-retries than was
* necessary. Added support to get hardware info. Updated for use
* with FreeBSD.
*
* 09/15/93 v0.2 pl01
* Fixed a bunch of bugs: extra isa_dmadone() in async_write() (shouldn't
* matter), fixed double buffering in async_req(), changed tape_end() in
* set_fdcmode() to reduce unexpected interrupts, changed end of track
* processing in async_req(), protected more of ftreq_rw() with an
* splbio(). Changed some of the ftreq_*() functions so that they wait
* for inactivity and then go, instead of aborting immediately.
*
* 08/07/93 v0.2 release
* Shifted from ftstrat to ioctl support for I/O. Streaming is now much
* more reliable. Added internal support for error correction, QIC-40,
* and variable length tapes. Random access of segments greatly
* improved. Formatting and verification support is close but still
* incomplete.
*
* 06/03/93 v0.1 Alpha release
* Hopefully the last re-write. Many bugs fixed, many remain.
*/
#include "ft.h"
#if NFT > 0
#include "fd.h"
#include <sys/param.h>
#include <sys/dkbad.h>
#include <sys/systm.h>
#include <sys/conf.h>
#include <sys/file.h>
#include <sys/proc.h>
#include <sys/ioctl.h>
#include <sys/malloc.h>
#include <sys/buf.h>
#include <sys/uio.h>
#include <sys/ftape.h>
#include <machine/cpufunc.h>
#include <i386/isa/isa_device.h>
#include <i386/isa/fdreg.h>
#include <i386/isa/fdc.h>
#include <i386/isa/icu.h>
#include <i386/isa/rtc.h>
#include <i386/isa/ftreg.h>
/* Enable or disable debugging messages. */
#define FTDBGALL 0 /* 1 if you want everything */
/*#define DPRT(a) printf a */
#define DPRT(a)
/* Constants private to the driver */
#define FTPRI (PRIBIO) /* sleep priority */
#define FTNBUFF 9 /* 8 for buffering, 1 for header */
/* The following items are needed from the fd driver. */
extern int in_fdc(int); /* read fdc registers */
extern int out_fdc(int, int); /* write fdc registers */
extern int hz; /* system clock rate */
/* Type of tape attached */
/* use numbers that don't interfere with the possible floppy types */
#define NO_TYPE 0 /* (same as NO_TYPE in fd.c) */
/* F_TAPE_TYPE must match value in fd.c */
#define F_TAPE_TYPE 0x020 /* bit for ft->types to indicate tape */
#define FT_NONE (F_TAPE_TYPE | 0) /* no method required */
#define FT_MOUNTAIN (F_TAPE_TYPE | 1) /* mountain */
#define FT_COLORADO (F_TAPE_TYPE | 2) /* colorado */
#define FT_INSIGHT (F_TAPE_TYPE | 3) /* insight */
/* Mode FDC is currently in: tape or disk */
enum { FDC_TAPE_MODE, FDC_DISK_MODE };
/* Command we are awaiting completion of */
enum { FTCMD_NONE, FTCMD_RESET, FTCMD_RECAL, FTCMD_SEEK, FTCMD_READID };
/* Tape interrupt status of current request */
enum { FTSTS_NONE, FTSTS_SNOOZE, FTSTS_INTERRUPT, FTSTS_TIMEOUT };
/* Tape I/O status */
enum {
FTIO_READY, /* No I/O activity */
FTIO_READING, /* Currently reading blocks */
FTIO_RDAHEAD, /* Currently reading ahead */
FTIO_WRITING /* Buffers are being written */
};
/* Current tape mode */
enum {
FTM_PRIMARY, /* Primary mode */
FTM_VERIFY, /* Verify mode */
FTM_FORMAT, /* Format mode */
FTM_DIAG1, /* Diagnostic mode 1 */
FTM_DIAG2 /* Diagnostic mode 2 */
};
/* Tape geometries table */
QIC_Geom ftgtbl[] = {
{ 0, 0, "Unformatted", "Unknown", 0, 0, 0, 0, 0 }, /* XXX */
{ 1, 1, "QIC-40", "205/550", 20, 68, 2176, 128, 21760 },
{ 1, 2, "QIC-40", "307.5/550", 20, 102, 3264, 128, 32640 },
{ 1, 3, "QIC-40", "295/900", 0, 0, 0, 0, 0 }, /* ??? */
{ 1, 4, "QIC-40", "1100/550", 20, 365, 11680, 128, 32512 },
{ 1, 5, "QIC-40", "1100/900", 0, 0, 0, 0, 0 }, /* ??? */
{ 2, 1, "QIC-80", "205/550", 28, 100, 3200, 128, 19200 },
{ 2, 2, "QIC-80", "307.5/550", 28, 150, 4800, 128, 19200 },
{ 2, 3, "QIC-80", "295/900", 0, 0, 0, 0, 0 }, /* ??? */
{ 2, 4, "QIC-80", "1100/550", 28, 537, 17184, 128, 32512 },
{ 2, 5, "QIC-80", "1100/900", 0, 0, 0, 0, 0 }, /* ??? */
{ 3, 1, "QIC-500", "205/550", 0, 0, 0, 0, 0 }, /* ??? */
{ 3, 2, "QIC-500", "307.5/550", 0, 0, 0, 0, 0 }, /* ??? */
{ 3, 3, "QIC-500", "295/900", 0, 0, 0, 0, 0 }, /* ??? */
{ 3, 4, "QIC-500", "1100/550", 0, 0, 0, 0, 0 }, /* ??? */
{ 3, 5, "QIC-500", "1100/900", 0, 0, 0, 0, 0 } /* ??? */
};
#define NGEOM (sizeof(ftgtbl) / sizeof(QIC_Geom))
QIC_Geom *ftg = NULL; /* Current tape's geometry */
/*
* things relating to asynchronous commands
*/
static int awr_state; /* state of async write */
static int ard_state; /* state of async read */
static int arq_state; /* state of async request */
static int async_retries; /* retries, one per invocation */
static int async_func; /* function to perform */
static int async_state; /* state current function is at */
static int async_arg0; /* up to 3 arguments for async cmds */
static int async_arg1; /**/
static int async_arg2; /**/
static int async_ret; /* return value */
static struct _astk {
int over_func;
int over_state;
int over_retries;
int over_arg0;
int over_arg1;
int over_arg2;
} astk[10];
static struct _astk *astk_ptr = &astk[0]; /* Pointer to stack position */
/* List of valid async (interrupt driven) tape support functions. */
enum {
ACMD_NONE, /* no command */
ACMD_SEEK, /* command seek */
ACMD_STATUS, /* report status */
ACMD_STATE, /* wait for state bits to be true */
ACMD_SEEKSTS, /* perform command and wait for status */
ACMD_READID, /* read id */
ACMD_RUNBLK /* ready tape for I/O on the given block */
};
/* Call another asyncronous command from within async_cmd(). */
#define CALL_ACMD(r,f,a,b,c) \
astk_ptr->over_retries = async_retries; \
astk_ptr->over_func = async_func; \
astk_ptr->over_state = (r); \
astk_ptr->over_arg0 = async_arg0; \
astk_ptr->over_arg1 = async_arg1; \
astk_ptr->over_arg2 = async_arg2; \
async_func = (f); async_state = 0; async_retries = 0; \
async_arg0=(a); async_arg1=(b); async_arg2=(c); \
astk_ptr++; \
goto restate
/* Perform an asyncronous command from outside async_cmd(). */
#define ACMD_FUNC(r,f,a,b,c) over_async = (r); astk_ptr = &astk[0]; \
async_func = (f); async_state = 0; async_retries = 0; \
async_arg0=(a); async_arg1=(b); async_arg2=(c); \
async_cmd(ftu); \
return
/* Various wait channels */
static char *wc_buff_avail = "bavail";
static char *wc_buff_done = "bdone";
static char *wc_iosts_change = "iochg";
static char *wc_long_delay = "ldelay";
static char *wc_intr_wait = "intrw";
#define ftsleep(wc,to) tsleep((caddr_t)(wc),FTPRI,(wc),(to))
/***********************************************************************\
* Per controller structure. *
\***********************************************************************/
extern struct fdc_data fdc_data[NFDC];
/***********************************************************************\
* Per tape drive structure. *
\***********************************************************************/
struct ft_data {
struct fdc_data *fdc; /* pointer to controller structure */
int ftsu; /* this units number on this controller */
int type; /* Drive type (Mountain, Colorado) */
/* QIC_Geom *ftg; */ /* pointer to Current tape's geometry */
int flags;
int cmd_wait; /* Command we are awaiting completion of */
int sts_wait; /* Tape interrupt status of current request */
int io_sts; /* Tape I/O status */
int mode;
int pcn; /* present cylinder number */
int attaching; /* true when ft is attaching */
unsigned char *xptr; /* pointer to buffer blk to xfer */
int xcnt; /* transfer count */
int xblk; /* block number to transfer */
int xseg; /* segment being transferred */
SegReq *segh; /* Current I/O request */
SegReq *segt; /* Tail of queued I/O requests */
SegReq *doneh; /* Completed I/O request queue */
SegReq *donet; /* Completed I/O request tail */
SegReq *segfree; /* Free segments */
SegReq *hdr; /* Current tape header */
int nsegq; /* Segments on request queue */
int ndoneq; /* Segments on completed queue */
int nfreelist; /* Segments on free list */
/* the next 3 should be defines in 'flags' */
int active; /* TRUE if transfer is active */
int rdonly; /* TRUE if tape is read-only */
int newcart; /* TRUE if new cartridge detected */
int laststs; /* last reported status code */
int lastcfg; /* last reported QIC config */
int lasterr; /* last QIC error code */
int lastpos; /* last known segment number */
int moving; /* TRUE if tape is moving */
int rid[7]; /* read_id return values */
} ft_data[NFT];
/***********************************************************************\
* Throughout this file the following conventions will be used: *
* ft is a pointer to the ft_data struct for the drive in question *
* fdc is a pointer to the fdc_data struct for the controller *
* ftu is the tape drive unit number *
* fdcu is the floppy controller unit number *
* ftsu is the tape drive unit number on that controller. (sub-unit) *
\***********************************************************************/
#define id_physid id_scsiid /* this biotab field doubles as a field */
/* for the physical unit number on the controller */
int ftopen(dev_t, int);
int ftclose(dev_t, int);
void ftstrategy(struct buf *);
int ftioctl(dev_t, int, caddr_t, int, struct proc *);
int ftdump(dev_t);
int ftsize(dev_t);
static timeout_t ft_timeout;
static void async_cmd(ftu_t);
static void async_req(ftu_t, int);
static void async_read(ftu_t, int);
static void async_write(ftu_t, int);
static void tape_start(ftu_t, int);
static void tape_end(ftu_t);
static void tape_inactive(ftu_t);
static int tape_cmd(ftu_t, int);
static int tape_status(ftu_t);
static int qic_status(ftu_t, int, int);
static int ftreq_rewind(ftu_t);
static int ftreq_hwinfo(ftu_t, QIC_HWInfo *);
/*****************************************************************************/
/*
* Allocate a segment I/O buffer from the free list.
*/
static SegReq *
segio_alloc(ft_p ft)
{
SegReq *r;
/* Grab first item from free list */
if ((r = ft->segfree) != NULL) {
ft->segfree = ft->segfree->next;
ft->nfreelist--;
}
DPRT(("segio_alloc: nfree=%d ndone=%d nreq=%d\n", ft->nfreelist, ft->ndoneq, ft->nsegq));
return(r);
}
/*
* Queue a segment I/O request.
*/
static void
segio_queue(ft_p ft, SegReq *sp)
{
/* Put request on in process queue. */
if (ft->segt == NULL)
ft->segh = sp;
else
ft->segt->next = sp;
sp->next = NULL;
ft->segt = sp;
ft->nsegq++;
DPRT(("segio_queue: nfree=%d ndone=%d nreq=%d\n", ft->nfreelist, ft->ndoneq, ft->nsegq));
}
/*
* Segment I/O completed, place on correct queue.
*/
static void
segio_done(ft_p ft, SegReq *sp)
{
/* First remove from current I/O queue */
ft->segh = sp->next;
if (ft->segh == NULL) ft->segt = NULL;
ft->nsegq--;
if (sp->reqtype == FTIO_WRITING) {
/* Place on free list */
sp->next = ft->segfree;
ft->segfree = sp;
ft->nfreelist++;
wakeup((caddr_t)wc_buff_avail);
DPRT(("segio_done: (w) nfree=%d ndone=%d nreq=%d\n", ft->nfreelist, ft->ndoneq, ft->nsegq));
} else {
/* Put on completed I/O queue */
if (ft->donet == NULL)
ft->doneh = sp;
else
ft->donet->next = sp;
sp->next = NULL;
ft->donet = sp;
ft->ndoneq++;
wakeup((caddr_t)wc_buff_done);
DPRT(("segio_done: (r) nfree=%d ndone=%d nreq=%d\n", ft->nfreelist, ft->ndoneq, ft->nsegq));
}
}
/*
* Take I/O request from finished queue to free queue.
*/
static void
segio_free(ft_p ft, SegReq *sp)
{
/* First remove from done queue */
ft->doneh = sp->next;
if (ft->doneh == NULL) ft->donet = NULL;
ft->ndoneq--;
/* Place on free list */
sp->next = ft->segfree;
ft->segfree = sp;
ft->nfreelist++;
wakeup((caddr_t)wc_buff_avail);
DPRT(("segio_free: nfree=%d ndone=%d nreq=%d\n", ft->nfreelist, ft->ndoneq, ft->nsegq));
}
/*
* Probe/attach floppy tapes.
*/
int
ftattach(isadev, fdup)
struct isa_device *isadev, *fdup;
{
fdcu_t fdcu = isadev->id_unit; /* fdc active unit */
fdc_p fdc = fdc_data + fdcu; /* pointer to controller structure */
ftu_t ftu = fdup->id_unit;
ft_p ft;
ftsu_t ftsu = fdup->id_physid;
QIC_HWInfo hw;
char *manu;
if (ftu >= NFT) return 0;
ft = &ft_data[ftu];
/* Probe for tape */
ft->attaching = 1;
ft->type = NO_TYPE;
ft->fdc = fdc;
ft->ftsu = ftsu;
/*
* FT_NONE - no method, just do it
*/
tape_start(ftu, 0);
if (tape_status(ftu) >= 0) {
ft->type = FT_NONE;
ftreq_hwinfo(ftu, &hw);
goto out;
}
/*
* FT_COLORADO - colorado style
*/
tape_start(ftu, 0);
tape_cmd(ftu, QC_COL_ENABLE1);
tape_cmd(ftu, QC_COL_ENABLE2 + ftu);
if (tape_status(ftu) >= 0) {
ft->type = FT_COLORADO;
ftreq_hwinfo(ftu, &hw);
tape_cmd(ftu, QC_COL_DISABLE);
goto out;
}
/*
* FT_MOUNTAIN - mountain style
*/
tape_start(ftu, 0);
tape_cmd(ftu, QC_MTN_ENABLE1);
tape_cmd(ftu, QC_MTN_ENABLE2);
if (tape_status(ftu) >= 0) {
ft->type = FT_MOUNTAIN;
ftreq_hwinfo(ftu, &hw);
tape_cmd(ftu, QC_MTN_DISABLE);
goto out;
}
/*
* FT_INSIGHT - insight style
*/
tape_start(ftu, 1);
if (tape_status(ftu) >= 0) {
ft->type = FT_INSIGHT;
ftreq_hwinfo(ftu, &hw);
goto out;
}
out:
tape_end(ftu);
if (ft->type != NO_TYPE) {
fdc->flags |= FDC_HASFTAPE;
switch(hw.hw_make) {
case 0x0000:
if (ft->type == FT_COLORADO)
manu = "Colorado";
else if (ft->type == FT_INSIGHT)
manu = "Insight";
else if (ft->type == FT_MOUNTAIN && hw.hw_model == 0x05)
manu = "Archive";
else if (ft->type == FT_MOUNTAIN)
manu = "Mountain";
else
manu = "Unknown";
break;
case 0x0001:
manu = "Colorado";
break;
case 0x0005:
if (hw.hw_model >= 0x09)
manu = "Conner";
else
manu = "Archive";
break;
case 0x0006:
manu = "Mountain";
break;
case 0x0007:
manu = "Wangtek";
break;
case 0x0222:
manu = "IOMega";
break;
default:
manu = "Unknown";
break;
}
printf(" [%d: ft%d: %s tape]", fdup->id_physid, fdup->id_unit, manu);
}
ft->attaching = 0;
return(ft->type);
}
/*
* Perform common commands asynchronously.
*/
static void
async_cmd(ftu_t ftu) {
ft_p ft = &ft_data[ftu];
fdcu_t fdcu = ft->fdc->fdcu;
int cmd, i, st0, st3, pcn;
static int bitn, retval, retpos, nbits, newcn;
static int wanttrk, wantblk, wantdir;
static int curtrk, curblk, curdir, curdiff;
static int errcnt = 0;
restate:
#if FTDBGALL
DPRT(("async_cmd state: func: %d state: %d\n", async_func, async_state));
#endif
switch(async_func) {
case ACMD_SEEK:
/*
* Arguments:
* 0 - command to perform
*/
switch (async_state) {
case 0:
cmd = async_arg0;
#if FTDBGALL
DPRT(("===>async_seek cmd = %d\n", cmd));
#endif
newcn = (cmd <= ft->pcn) ? ft->pcn - cmd : ft->pcn + cmd;
async_state = 1;
i = 0;
if (out_fdc(fdcu, NE7CMD_SEEK) < 0) i = 1;
if (!i && out_fdc(fdcu, ftu) < 0) i = 1;
if (!i && out_fdc(fdcu, newcn) < 0) i = 1;
if (i) {
if (++async_retries >= 10) {
DPRT(("ft%d: async_cmd command seek failed!!\n", ftu));
goto complete;
}
DPRT(("ft%d: async_cmd command seek retry...\n",ftu));
async_state = 0;
goto restate;
}
break;
case 1:
out_fdc(fdcu, NE7CMD_SENSEI);
st0 = in_fdc(fdcu);
pcn = in_fdc(fdcu);
if (st0 < 0 || pcn < 0 || newcn != pcn) {
if (++async_retries >= 10) {
DPRT(("ft%d: async_cmd seek retries exceeded\n",ftu));
goto complete;
}
DPRT(("ft%d: async_cmd command bad st0=$%02x pcn=$%02x\n",
ftu, st0, pcn));
async_state = 0;
timeout(ft_timeout, (caddr_t)ftu, hz/10);
break;
}
if (st0 & 0x20) { /* seek done */
ft->pcn = pcn;
}
#if FTDBGALL
else
DPRT(("ft%d: async_seek error st0 = $%02x pcn = %d\n",
ftu, st0, pcn));
#endif
if (async_arg1) goto complete;
async_state = 2;
timeout(ft_timeout, (caddr_t)ftu, hz/50);
break;
case 2:
goto complete;
/* NOTREACHED */
}
break;
case ACMD_STATUS:
/*
* Arguments:
* 0 - command to issue report from
* 1 - number of bits
* modifies: bitn, retval, st3
*/
switch (async_state) {
case 0:
bitn = 0;
retval = 0;
cmd = async_arg0;
nbits = async_arg1;
DPRT(("async_status got cmd = %d nbits = %d\n", cmd,nbits));
CALL_ACMD(5, ACMD_SEEK, QC_NEXTBIT, 0, 0);
/* NOTREACHED */
case 1:
out_fdc(fdcu, NE7CMD_SENSED);
out_fdc(fdcu, ftu);
st3 = in_fdc(fdcu);
if (st3 < 0) {
DPRT(("ft%d: async_status timed out on bit %d r=$%02x\n",
ftu,bitn,retval));
async_ret = -1;
goto complete;
}
if ((st3 & 0x10) != 0) retval |= (1 << bitn);
bitn++;
if (bitn >= (nbits+2)) {
if ((retval & 1) && (retval & (1 << (nbits+1)))) {
async_ret = (retval & ~(1<<(nbits+1))) >> 1;
if (async_arg0 == QC_STATUS && async_arg2 == 0 &&
(async_ret & (QS_ERROR|QS_NEWCART))) {
async_state = 2;
goto restate;
}
DPRT(("async status got $%04x ($%04x)\n", async_ret,retval));
} else {
DPRT(("ft%d: async_status failed: retval=$%04x nbits=%d\n",
ftu, retval,nbits));
async_ret = -2;
}
goto complete;
}
CALL_ACMD(1, ACMD_SEEK, QC_NEXTBIT, 0, 0);
/* NOTREACHED */
case 2:
if (async_ret & QS_NEWCART) ft->newcart = 1;
CALL_ACMD(3, ACMD_STATUS, QC_ERRCODE, 16, 1);
case 3:
ft->lasterr = async_ret;
if ((ft->lasterr & QS_NEWCART) == 0 && ft->lasterr) {
DPRT(("ft%d: QIC error %d occurred on cmd %d\n",
ftu, ft->lasterr & 0xff, ft->lasterr >> 8));
}
cmd = async_arg0;
nbits = async_arg1;
CALL_ACMD(4, ACMD_STATUS, QC_STATUS, 8, 1);
case 4:
goto complete;
case 5:
CALL_ACMD(6, ACMD_SEEK, QC_NEXTBIT, 0, 0);
case 6:
CALL_ACMD(7, ACMD_SEEK, QC_NEXTBIT, 0, 0);
case 7:
CALL_ACMD(8, ACMD_SEEK, QC_NEXTBIT, 0, 0);
case 8:
cmd = async_arg0;
CALL_ACMD(1, ACMD_SEEK, cmd, 0, 0);
}
break;
case ACMD_STATE:
/*
* Arguments:
* 0 - status bits to check
*/
switch(async_state) {
case 0:
CALL_ACMD(1, ACMD_STATUS, QC_STATUS, 8, 0);
case 1:
if ((async_ret & async_arg0) != 0) goto complete;
async_state = 0;
if (++async_retries == 360) { /* 90 secs. */
DPRT(("ft%d: acmd_state exceeded retry count\n", ftu));
goto complete;
}
timeout(ft_timeout, (caddr_t)ftu, hz/4);
break;
}
break;
case ACMD_SEEKSTS:
/*
* Arguments:
* 0 - command to perform
* 1 - status bits to check
* 2 - (optional) seconds to wait until completion
*/
switch(async_state) {
case 0:
cmd = async_arg0;
async_retries = (async_arg2) ? (async_arg2 * 4) : 10;
CALL_ACMD(1, ACMD_SEEK, cmd, 0, 0);
case 1:
CALL_ACMD(2, ACMD_STATUS, QC_STATUS, 8, 0);
case 2:
if ((async_ret & async_arg1) != 0) goto complete;
if (--async_retries == 0) {
DPRT(("ft%d: acmd_seeksts retries exceeded\n", ftu));
goto complete;
}
async_state = 1;
timeout(ft_timeout, (caddr_t)ftu, hz/4);
break;
}
break;
case ACMD_READID:
/*
* Arguments: (none)
*/
switch(async_state) {
case 0:
if (!ft->moving) {
CALL_ACMD(4, ACMD_SEEKSTS, QC_STOP, QS_READY, 0);
/* NOTREACHED */
}
async_state = 1;
out_fdc(fdcu, 0x4a); /* READ_ID */
out_fdc(fdcu, ftu);
break;
case 1:
for (i = 0; i < 7; i++) ft->rid[i] = in_fdc(fdcu);
async_ret = (ft->rid[3]*ftg->g_fdtrk) +
(ft->rid[4]*ftg->g_fdside) + ft->rid[5] - 1;
DPRT(("readid st0:%02x st1:%02x st2:%02x c:%d h:%d s:%d pos:%d\n",
ft->rid[0], ft->rid[1], ft->rid[2], ft->rid[3],
ft->rid[4], ft->rid[5], async_ret));
if ((ft->rid[0] & 0xc0) != 0 || async_ret < 0) {
/*
* Method for retry:
* errcnt == 1 regular retry
* 2 microstep head 1
* 3 microstep head 2
* 4 microstep head back to 0
* 5 fail
*/
if (++errcnt >= 5) {
DPRT(("ft%d: acmd_readid errcnt exceeded\n", fdcu));
async_ret = -2;
errcnt = 0;
goto complete;
}
if (errcnt == 1) {
ft->moving = 0;
CALL_ACMD(4, ACMD_SEEKSTS, QC_STOP, QS_READY, 0);
} else {
ft->moving = 0;
CALL_ACMD(4, ACMD_SEEKSTS, QC_STPAUSE, QS_READY, 0);
}
DPRT(("readid retry %d...\n", errcnt));
async_state = 0;
goto restate;
}
if ((async_ret % ftg->g_blktrk) == (ftg->g_blktrk-1)) {
DPRT(("acmd_readid detected last block on track\n"));
retpos = async_ret;
CALL_ACMD(2, ACMD_STATE, QS_BOT|QS_EOT, 0, 0);
/* NOTREACHED */
}
ft->lastpos = async_ret;
errcnt = 0;
goto complete;
/* NOTREACHED */
case 2:
CALL_ACMD(3, ACMD_STATE, QS_READY, 0, 0);
case 3:
ft->moving = 0;
async_ret = retpos+1;
goto complete;
case 4:
CALL_ACMD(5, ACMD_SEEK, QC_FORWARD, 0, 0);
case 5:
ft->moving = 1;
async_state = 0;
timeout(ft_timeout, (caddr_t)ftu, hz/10); /* XXX */
break;
}
break;
case ACMD_RUNBLK:
/*
* Arguments:
* 0 - block number I/O will be performed on
*
* modifies: curpos
*/
switch (async_state) {
case 0:
wanttrk = async_arg0 / ftg->g_blktrk;
wantblk = async_arg0 % ftg->g_blktrk;
wantdir = wanttrk & 1;
ft->moving = 0;
CALL_ACMD(1, ACMD_SEEKSTS, QC_STOP, QS_READY, 0);
case 1:
curtrk = wanttrk;
curdir = curtrk & 1;
DPRT(("Changing to track %d\n", wanttrk));
CALL_ACMD(2, ACMD_SEEK, QC_SEEKTRACK, 0, 0);
case 2:
cmd = wanttrk+2;
CALL_ACMD(3, ACMD_SEEKSTS, cmd, QS_READY, 0);
case 3:
CALL_ACMD(4, ACMD_STATUS, QC_STATUS, 8, 0);
case 4:
ft->laststs = async_ret;
if (wantblk == 0) {
curblk = 0;
cmd = (wantdir) ? QC_SEEKEND : QC_SEEKSTART;
CALL_ACMD(6, ACMD_SEEKSTS, cmd, QS_READY, 90);
}
if (ft->laststs & QS_BOT) {
DPRT(("Tape is at BOT\n"));
curblk = (wantdir) ? 4800 : 0;
async_state = 6;
goto restate;
}
if (ft->laststs & QS_EOT) {
DPRT(("Tape is at EOT\n"));
curblk = (wantdir) ? 0 : 4800;
async_state = 6;
goto restate;
}
CALL_ACMD(5, ACMD_READID, 0, 0, 0);
case 5:
if (async_ret < 0) {
ft->moving = 0;
ft->lastpos = -2;
if (async_ret == -2) {
CALL_ACMD(9, ACMD_SEEKSTS, QC_STOP, QS_READY, 0);
}
CALL_ACMD(1, ACMD_SEEKSTS, QC_STOP, QS_READY, 0);
}
curtrk = (async_ret+1) / ftg->g_blktrk;
curblk = (async_ret+1) % ftg->g_blktrk;
DPRT(("gotid: curtrk=%d wanttrk=%d curblk=%d wantblk=%d\n",
curtrk, wanttrk, curblk, wantblk));
if (curtrk != wanttrk) { /* oops! */
DPRT(("oops!! wrong track!\n"));
CALL_ACMD(1, ACMD_SEEKSTS, QC_STOP, QS_READY, 0);
}
async_state = 6;
goto restate;
case 6:
DPRT(("curtrk = %d nextblk = %d\n", curtrk, curblk));
if (curblk == wantblk) {
ft->lastpos = curblk - 1;
async_ret = ft->lastpos;
if (ft->moving) goto complete;
CALL_ACMD(7, ACMD_STATE, QS_READY, 0, 0);
}
if (curblk > wantblk) { /* passed it */
ft->moving = 0;
CALL_ACMD(10, ACMD_SEEKSTS, QC_STOP, QS_READY, 0);
}
if ((wantblk - curblk) <= 256) { /* approaching it */
CALL_ACMD(5, ACMD_READID, 0, 0, 0);
}
/* way up ahead */
ft->moving = 0;
CALL_ACMD(14, ACMD_SEEKSTS, QC_STOP, QS_READY, 0);
break;
case 7:
ft->moving = 1;
CALL_ACMD(8, ACMD_SEEK, QC_FORWARD, 0, 0);
break;
case 8:
async_state = 9;
timeout(ft_timeout, (caddr_t)ftu, hz/10); /* XXX */
break;
case 9:
goto complete;
case 10:
curdiff = ((curblk - wantblk) / QCV_BLKSEG) + 2;
if (curdiff >= ftg->g_segtrk) curdiff = ftg->g_segtrk - 1;
DPRT(("pos %d past %d, reverse %d\n", curblk, wantblk, curdiff));
CALL_ACMD(11, ACMD_SEEK, QC_SEEKREV, 0, 0);
case 11:
DPRT(("reverse 1 done\n"));
CALL_ACMD(12, ACMD_SEEK, (curdiff & 0xf)+2, 0, 0);
case 12:
DPRT(("reverse 2 done\n"));
CALL_ACMD(13, ACMD_SEEKSTS, ((curdiff>>4)&0xf)+2, QS_READY, 90);
case 13:
CALL_ACMD(5, ACMD_READID, 0, 0, 0);
case 14:
curdiff = ((wantblk - curblk) / QCV_BLKSEG) - 2;
if (curdiff < 0) curdiff = 0;
DPRT(("pos %d before %d, forward %d\n", curblk, wantblk, curdiff));
CALL_ACMD(15, ACMD_SEEK, QC_SEEKFWD, 0, 0);
case 15:
DPRT(("forward 1 done\n"));
CALL_ACMD(16, ACMD_SEEK, (curdiff & 0xf)+2, 0, 0);
case 16:
DPRT(("forward 2 done\n"));
CALL_ACMD(13, ACMD_SEEKSTS, ((curdiff>>4)&0xf)+2, QS_READY, 90);
}
break;
}
return;
complete:
if (astk_ptr != &astk[0]) {
astk_ptr--;
async_retries = astk_ptr->over_retries;
async_func = astk_ptr->over_func;
async_state = astk_ptr->over_state;
async_arg0 = astk_ptr->over_arg0;
async_arg1 = astk_ptr->over_arg1;
async_arg2 = astk_ptr->over_arg2;
goto restate;
}
async_func = ACMD_NONE;
async_state = 0;
switch (ft->io_sts) {
case FTIO_READY:
async_req(ftu, 2);
break;
case FTIO_READING:
case FTIO_RDAHEAD:
async_read(ftu, 2);
break;
case FTIO_WRITING:
async_write(ftu, 2);
break;
default:
DPRT(("ft%d: bad async_cmd ending I/O state!\n", ftu));
break;
}
}
/*
* Entry point for the async request processor.
*/
static void
async_req(ftu_t ftu, int from)
{
ft_p ft = &ft_data[ftu];
SegReq *sp;
static int over_async, lastreq;
int cmd;
if (from == 2) arq_state = over_async;
restate:
switch (arq_state) {
case 0: /* Process segment */
sp = ft->segh;
ft->io_sts = (sp == NULL) ? FTIO_READY : sp->reqtype;
if (ft->io_sts == FTIO_WRITING)
async_write(ftu, from);
else
async_read(ftu, from);
if (ft->io_sts != FTIO_READY) return;
/* Pull buffer from current I/O queue */
if (sp != NULL) {
lastreq = sp->reqtype;
segio_done(ft, sp);
/* If I/O cancelled, clear finished queue. */
if (sp->reqcan) {
while (ft->doneh != NULL)
segio_free(ft, ft->doneh);
lastreq = FTIO_READY;
}
} else
lastreq = FTIO_READY;
/* Detect end of track */
if (((ft->xblk / QCV_BLKSEG) % ftg->g_segtrk) == 0) {
ACMD_FUNC(2, ACMD_STATE, QS_BOT|QS_EOT, 0, 0);
}
arq_state = 1;
goto restate;
case 1: /* Next request */
/* If we have another request queued, start it running. */
if (ft->segh != NULL) {
sp = ft->segh;
sp->reqcrc = 0;
arq_state = ard_state = awr_state = 0;
ft->xblk = sp->reqblk;
ft->xseg = sp->reqseg;
ft->xcnt = 0;
ft->xptr = sp->buff;
DPRT(("I/O reqblk = %d\n", ft->xblk));
goto restate;
}
/* If the last request was reading, do read ahead. */
if ((lastreq == FTIO_READING || lastreq == FTIO_RDAHEAD) &&
(sp = segio_alloc(ft)) != NULL) {
sp->reqtype = FTIO_RDAHEAD;
sp->reqblk = ft->xblk;
sp->reqseg = ft->xseg+1;
sp->reqcrc = 0;
sp->reqcan = 0;
segio_queue(ft, sp);
bzero(sp->buff, QCV_SEGSIZE);
arq_state = ard_state = awr_state = 0;
ft->xblk = sp->reqblk;
ft->xseg = sp->reqseg;
ft->xcnt = 0;
ft->xptr = sp->buff;
DPRT(("Processing readahead reqblk = %d\n", ft->xblk));
goto restate;
}
if (ft->moving) {
DPRT(("No more I/O.. Stopping.\n"));
ft->moving = 0;
ACMD_FUNC(7, ACMD_SEEKSTS, QC_PAUSE, QS_READY, 0);
break;
}
arq_state = 7;
goto restate;
case 2: /* End of track */
ft->moving = 0;
ACMD_FUNC(3, ACMD_STATE, QS_READY, 0, 0);
break;
case 3:
DPRT(("async_req seek head to track %d\n", ft->xblk / ftg->g_blktrk));
ACMD_FUNC(4, ACMD_SEEK, QC_SEEKTRACK, 0, 0);
break;
case 4:
cmd = (ft->xblk / ftg->g_blktrk) + 2;
if (ft->segh != NULL) {
ACMD_FUNC(5, ACMD_SEEKSTS, cmd, QS_READY, 0);
} else {
ACMD_FUNC(7, ACMD_SEEKSTS, cmd, QS_READY, 0);
}
break;
case 5:
ft->moving = 1;
ACMD_FUNC(6, ACMD_SEEK, QC_FORWARD, 0, 0);
break;
case 6:
arq_state = 1;
timeout(ft_timeout, (caddr_t)ftu, hz/10); /* XXX */
break;
case 7:
/* Time to rest. */
ft->active = 0;
ft->lastpos = -2;
/* wakeup those who want an i/o chg */
wakeup((caddr_t)wc_iosts_change);
break;
}
}
/*
* Entry for async read.
*/
static void
async_read(ftu_t ftu, int from)
{
ft_p ft = &ft_data[ftu];
fdcu_t fdcu = ft->fdc->fdcu; /* fdc active unit */
int i, rddta[7];
int where;
static int over_async;
static int retries = 0;
if (from == 2) ard_state = over_async;
restate:
#if FTDBGALL
DPRT(("async_read: state: %d from = %d\n", ard_state, from));
#endif
switch (ard_state) {
case 0: /* Start off */
/* If tape is not at desired position, stop and locate */
if (ft->lastpos != (ft->xblk-1)) {
DPRT(("ft%d: position unknown: lastpos:%d ft->xblk:%d\n",
ftu, ft->lastpos, ft->xblk));
ACMD_FUNC(1, ACMD_RUNBLK, ft->xblk, 0, 0);
}
/* Tape is in position but stopped. */
if (!ft->moving) {
DPRT(("async_read ******STARTING TAPE\n"));
ACMD_FUNC(3, ACMD_STATE, QS_READY, 0, 0);
}
ard_state = 1;
goto restate;
case 1: /* Start DMA */
/* Tape is now moving and in position-- start DMA now! */
isa_dmastart(B_READ, ft->xptr, QCV_BLKSIZE, 2);
out_fdc(fdcu, 0x66); /* read */
out_fdc(fdcu, ftu); /* unit */
out_fdc(fdcu, (ft->xblk % ftg->g_fdside) / ftg->g_fdtrk); /* cylinder */
out_fdc(fdcu, ft->xblk / ftg->g_fdside); /* head */
out_fdc(fdcu, (ft->xblk % ftg->g_fdtrk) + 1); /* sector */
out_fdc(fdcu, 0x03); /* 1K sectors */
out_fdc(fdcu, (ft->xblk % ftg->g_fdtrk) + 1); /* count */
out_fdc(fdcu, 0x74); /* gap length */
out_fdc(fdcu, 0xff); /* transfer size */
ard_state = 2;
break;
case 2: /* DMA completed */
/* Transfer complete, get status */
for (i = 0; i < 7; i++) rddta[i] = in_fdc(fdcu);
isa_dmadone(B_READ, ft->xptr, QCV_BLKSIZE, 2);
#if FTDBGALL
/* Compute where the controller thinks we are */
where = (rddta[3]*ftg->g_fdtrk) + (rddta[4]*ftg->g_fdside)
+ rddta[5]-1;
DPRT(("xfer done: st0:%02x st1:%02x st2:%02x c:%d h:%d s:%d pos:%d want:%d\n",
rddta[0], rddta[1], rddta[2], rddta[3], rddta[4], rddta[5],
where, ft->xblk));
#endif
/* Check for errors */
if ((rddta[0] & 0xc0) != 0x00) {
#if !FTDBGALL
where = (rddta[3]*ftg->g_fdtrk) + (rddta[4]*ftg->g_fdside)
+ rddta[5]-1;
DPRT(("xd: st0:%02x st1:%02x st2:%02x c:%d h:%d s:%d pos:%d want:%d\n",
rddta[0], rddta[1], rddta[2], rddta[3], rddta[4], rddta[5],
where, ft->xblk));
#endif
if ((rddta[1] & 0x04) == 0x04 && retries < 2) {
/* Probably wrong position */
DPRT(("async_read: doing retry %d\n", retries));
ft->lastpos = ft->xblk;
ard_state = 0;
retries++;
goto restate;
} else {
/* CRC/Address-mark/Data-mark, et. al. */
DPRT(("ft%d: CRC error on block %d\n", fdcu, ft->xblk));
ft->segh->reqcrc |= (1 << ft->xcnt);
}
}
/* Otherwise, transfer completed okay. */
retries = 0;
ft->lastpos = ft->xblk;
ft->xblk++;
ft->xcnt++;
ft->xptr += QCV_BLKSIZE;
if (ft->xcnt < QCV_BLKSEG && ft->segh->reqcan == 0) {
ard_state = 0;
goto restate;
}
DPRT(("Read done.. Cancel = %d\n", ft->segh->reqcan));
ft->io_sts = FTIO_READY;
break;
case 3:
ft->moving = 1;
ACMD_FUNC(4, ACMD_SEEK, QC_FORWARD, 0, 0);
break;
case 4:
ard_state = 1;
timeout(ft_timeout, (caddr_t)ftu, hz/10); /* XXX */
break;
default:
DPRT(("ft%d: bad async_read state %d!!\n", ftu, ard_state));
break;
}
}
/*
* Entry for async write. If from is 0, this came from the interrupt
* routine, if it's 1 then it was a timeout, if it's 2, then an
* async_cmd completed.
*/
static void
async_write(ftu_t ftu, int from)
{
ft_p ft = &ft_data[ftu];
fdcu_t fdcu = ft->fdc->fdcu; /* fdc active unit */
int i, rddta[7];
int where;
static int over_async;
static int retries = 0;
if (from == 2) awr_state = over_async;
restate:
#if FTDBGALL
DPRT(("async_write: state: %d from = %d\n", awr_state, from));
#endif
switch (awr_state) {
case 0: /* Start off */
/* If tape is not at desired position, stop and locate */
if (ft->lastpos != (ft->xblk-1)) {
DPRT(("ft%d: position unknown: lastpos:%d ft->xblk:%d\n",
ftu, ft->lastpos, ft->xblk));
ACMD_FUNC(1, ACMD_RUNBLK, ft->xblk, 0, 0);
}
/* Tape is in position but stopped. */
if (!ft->moving) {
DPRT(("async_write ******STARTING TAPE\n"));
ACMD_FUNC(3, ACMD_STATE, QS_READY, 0, 0);
}
awr_state = 1;
goto restate;
case 1: /* Start DMA */
/* Tape is now moving and in position-- start DMA now! */
isa_dmastart(B_WRITE, ft->xptr, QCV_BLKSIZE, 2);
out_fdc(fdcu, 0x45); /* write */
out_fdc(fdcu, ftu); /* unit */
out_fdc(fdcu, (ft->xblk % ftg->g_fdside) / ftg->g_fdtrk); /* cyl */
out_fdc(fdcu, ft->xblk / ftg->g_fdside); /* head */
out_fdc(fdcu, (ft->xblk % ftg->g_fdtrk) + 1); /* sector */
out_fdc(fdcu, 0x03); /* 1K sectors */
out_fdc(fdcu, (ft->xblk % ftg->g_fdtrk) + 1); /* count */
out_fdc(fdcu, 0x74); /* gap length */
out_fdc(fdcu, 0xff); /* transfer size */
awr_state = 2;
break;
case 2: /* DMA completed */
/* Transfer complete, get status */
for (i = 0; i < 7; i++) rddta[i] = in_fdc(fdcu);
isa_dmadone(B_WRITE, ft->xptr, QCV_BLKSIZE, 2);
#if FTDBGALL
/* Compute where the controller thinks we are */
where = (rddta[3]*ftg->g_fdtrk) + (rddta[4]*ftg->g_fdside) + rddta[5]-1;
DPRT(("xfer done: st0:%02x st1:%02x st2:%02x c:%d h:%d s:%d pos:%d want:%d\n",
rddta[0], rddta[1], rddta[2], rddta[3], rddta[4], rddta[5],
where, ft->xblk));
#endif
/* Check for errors */
if ((rddta[0] & 0xc0) != 0x00) {
#if !FTDBGALL
where = (rddta[3]*ftg->g_fdtrk) + (rddta[4]*ftg->g_fdside)
+ rddta[5]-1;
DPRT(("xfer done: st0:%02x st1:%02x st2:%02x c:%d h:%d s:%d pos:%d want:%d\n",
rddta[0], rddta[1], rddta[2], rddta[3], rddta[4], rddta[5],
where, ft->xblk));
#endif
if (retries < 3) {
/* Something happened -- try again */
DPRT(("async_write: doing retry %d\n", retries));
ft->lastpos = ft->xblk;
awr_state = 0;
retries++;
goto restate;
} else {
/*
* Retries failed. Note the unrecoverable error.
* Marking the block as bad is useless right now.
*/
printf("ft%d: unrecoverable write error on block %d\n",
ftu, ft->xblk);
ft->segh->reqcrc |= (1 << ft->xcnt);
}
}
/* Otherwise, transfer completed okay. */
retries = 0;
ft->lastpos = ft->xblk;
ft->xblk++;
ft->xcnt++;
ft->xptr += QCV_BLKSIZE;
if (ft->xcnt < QCV_BLKSEG) {
awr_state = 0; /* next block */
goto restate;
}
#if FTDBGALL
DPRT(("Write done.\n"));
#endif
ft->io_sts = FTIO_READY;
break;
case 3:
ft->moving = 1;
ACMD_FUNC(4, ACMD_SEEK, QC_FORWARD, 0, 0);
break;
case 4:
awr_state = 1;
timeout(ft_timeout, (caddr_t)ftu, hz/10); /* XXX */
break;
default:
DPRT(("ft%d: bad async_write state %d!!\n", ftu, awr_state));
break;
}
}
/*
* Interrupt handler for active tape. Bounced off of fdintr().
*/
int
ftintr(ftu_t ftu)
{
int st0, pcn, i;
ft_p ft = &ft_data[ftu];
fdcu_t fdcu = ft->fdc->fdcu; /* fdc active unit */
int s = splbio();
st0 = 0;
pcn = 0;
/* I/O segment transfer completed */
if (ft->active) {
if (async_func != ACMD_NONE) {
async_cmd(ftu);
splx(s);
return(1);
}
#if FTDBGALL
DPRT(("Got request interrupt\n"));
#endif
async_req(ftu, 0);
splx(s);
return(1);
}
/* Get interrupt status */
if (ft->cmd_wait != FTCMD_READID) {
out_fdc(fdcu, NE7CMD_SENSEI);
st0 = in_fdc(fdcu);
pcn = in_fdc(fdcu);
}
if (ft->cmd_wait == FTCMD_NONE || ft->sts_wait != FTSTS_SNOOZE) {
huh_what:
printf("ft%d: unexpected interrupt; st0 = $%02x pcn = %d\n",
ftu, st0, pcn);
splx(s);
return(1);
}
switch (ft->cmd_wait) {
case FTCMD_RESET:
ft->sts_wait = FTSTS_INTERRUPT;
wakeup((caddr_t)wc_intr_wait);
break;
case FTCMD_RECAL:
case FTCMD_SEEK:
if (st0 & 0x20) { /* seek done */
ft->sts_wait = FTSTS_INTERRUPT;
ft->pcn = pcn;
wakeup((caddr_t)wc_intr_wait);
}
#if FTDBGALL
else
DPRT(("ft%d: seek error st0 = $%02x pcn = %d\n",
ftu, st0, pcn));
#endif
break;
case FTCMD_READID:
for (i = 0; i < 7; i++) ft->rid[i] = in_fdc(fdcu);
ft->sts_wait = FTSTS_INTERRUPT;
wakeup((caddr_t)wc_intr_wait);
break;
default:
goto huh_what;
}
splx(s);
return(1);
}
/*
* Interrupt timeout routine.
*/
static void
ft_timeout(void *arg1)
{
int s;
ftu_t ftu = (ftu_t)arg1;
ft_p ft = &ft_data[ftu];
s = splbio();
if (ft->active) {
if (async_func != ACMD_NONE) {
async_cmd(ftu);
splx(s);
return;
}
async_req(ftu, 1);
} else {
ft->sts_wait = FTSTS_TIMEOUT;
wakeup((caddr_t)wc_intr_wait);
}
splx(s);
}
/*
* Wait for a particular interrupt to occur. ftintr() will wake us up
* if it sees what we want. Otherwise, time out and return error.
* Should always disable ints before trigger is sent and calling here.
*/
static int
ftintr_wait(ftu_t ftu, int cmd, int ticks)
{
int retries, st0, pcn;
ft_p ft = &ft_data[ftu];
fdcu_t fdcu = ft->fdc->fdcu; /* fdc active unit */
ft->cmd_wait = cmd;
ft->sts_wait = FTSTS_SNOOZE;
/* At attach time, we can't rely on having interrupts serviced */
if (ft->attaching) {
switch (cmd) {
case FTCMD_RESET:
DELAY(100);
ft->sts_wait = FTSTS_INTERRUPT;
goto intrdone;
case FTCMD_RECAL:
case FTCMD_SEEK:
for (retries = 0; retries < 10000; retries++) {
out_fdc(fdcu, NE7CMD_SENSEI);
st0 = in_fdc(fdcu);
pcn = in_fdc(fdcu);
if (st0 & 0x20) {
ft->sts_wait = FTSTS_INTERRUPT;
ft->pcn = pcn;
goto intrdone;
}
DELAY(100);
}
break;
}
ft->sts_wait = FTSTS_TIMEOUT;
goto intrdone;
}
ftsleep(wc_intr_wait, ticks);
intrdone:
if (ft->sts_wait == FTSTS_TIMEOUT) { /* timeout */
#if FTDBGALL
if (ft->cmd_wait != FTCMD_RESET)
DPRT(("ft%d: timeout on command %d\n", ftu, ft->cmd_wait));
#endif
ft->cmd_wait = FTCMD_NONE;
ft->sts_wait = FTSTS_NONE;
return(1);
}
/* got interrupt */
if (ft->attaching == 0 && ticks) untimeout(ft_timeout, (caddr_t)ftu);
ft->cmd_wait = FTCMD_NONE;
ft->sts_wait = FTSTS_NONE;
return(0);
}
/*
* Recalibrate tape drive. Parameter totape is true, if we should
* recalibrate to tape drive settings.
*/
static int
tape_recal(ftu_t ftu, int totape)
{
int s;
ft_p ft = &ft_data[ftu];
fdcu_t fdcu = ft->fdc->fdcu; /* fdc active unit */
DPRT(("tape_recal start\n"));
out_fdc(fdcu, NE7CMD_SPECIFY);
out_fdc(fdcu, (totape) ? 0xAD : 0xDF);
out_fdc(fdcu, 0x02);
s = splbio();
out_fdc(fdcu, NE7CMD_RECAL);
out_fdc(fdcu, ftu);
if (ftintr_wait(ftu, FTCMD_RECAL, hz)) {
splx(s);
DPRT(("ft%d: recalibrate timeout\n", ftu));
return(1);
}
splx(s);
out_fdc(fdcu, NE7CMD_SPECIFY);
out_fdc(fdcu, (totape) ? 0xFD : 0xDF);
out_fdc(fdcu, 0x02);
DPRT(("tape_recal end\n"));
return(0);
}
/*
* Wait for a particular tape status to be met. If all is TRUE, then
* all states must be met, otherwise any state can be met.
*/
static int
tape_state(ftu_t ftu, int all, int mask, int seconds)
{
int r, tries, maxtries;
maxtries = (seconds) ? (4 * seconds) : 1;
for (tries = 0; tries < maxtries; tries++) {
r = tape_status(ftu);
if (r >= 0) {
if (all && (r & mask) == mask) return(r);
if ((r & mask) != 0) return(r);
}
if (seconds) ftsleep(wc_long_delay, hz/4);
}
DPRT(("ft%d: tape_state failed on mask=$%02x maxtries=%d\n",
ftu, mask, maxtries));
return(-1);
}
/*
* Send a QIC command to tape drive, wait for completion.
*/
static int
tape_cmd(ftu_t ftu, int cmd)
{
int newcn;
int retries = 0;
int s;
ft_p ft = &ft_data[ftu];
fdcu_t fdcu = ft->fdc->fdcu; /* fdc active unit */
DPRT(("===> tape_cmd: %d\n",cmd));
newcn = (cmd <= ft->pcn) ? ft->pcn - cmd : ft->pcn + cmd;
retry:
/* Perform seek */
s = splbio();
out_fdc(fdcu, NE7CMD_SEEK);
out_fdc(fdcu, ftu);
out_fdc(fdcu, newcn);
if (ftintr_wait(ftu, FTCMD_SEEK, hz)) {
DPRT(("ft%d: tape_cmd seek timeout\n", ftu));
redo:
splx(s);
if (++retries < 5) goto retry;
DPRT(("ft%d: tape_cmd seek failed!\n", ftu));
return(1);
}
splx(s);
if (ft->pcn != newcn) {
DPRT(("ft%d: bad seek in tape_cmd; pcn = %d newcn = %d\n",
ftu, ft->pcn, newcn));
goto redo;
}
DELAY(2500);
return(0);
}
/*
* Return status of tape drive
*/
static int
tape_status(ftu_t ftu)
{
int r, err, tries;
ft_p ft = &ft_data[ftu];
int max = (ft->attaching) ? 2 : 3;
for (r = -1, tries = 0; r < 0 && tries < max; tries++)
r = qic_status(ftu, QC_STATUS, 8);
if (tries == max) return(-1);
recheck:
DPRT(("tape_status got $%04x\n",r));
ft->laststs = r;
if (r & (QS_ERROR|QS_NEWCART)) {
err = qic_status(ftu, QC_ERRCODE, 16);
ft->lasterr = err;
if (r & QS_NEWCART) {
ft->newcart = 1;
/* If tape not referenced, do a seek load point. */
if ((r & QS_FMTOK) == 0 && !ft->attaching) {
tape_cmd(ftu, QC_SEEKLP);
do {
ftsleep(wc_long_delay, hz);
} while ((r = qic_status(ftu, QC_STATUS, 8)) < 0 ||
(r & (QS_READY|QS_CART)) == QS_CART);
goto recheck;
}
} else if (err && !ft->attaching) {
DPRT(("ft%d: QIC error %d occurred on cmd %d\n",
ftu, err & 0xff, err >> 8));
}
r = qic_status(ftu, QC_STATUS, 8);
ft->laststs = r;
DPRT(("tape_status got error code $%04x new sts = $%02x\n",err,r));
}
ft->rdonly = (r & QS_RDONLY);
return(r);
}
/*
* Transfer control to tape drive.
*/
static void
tape_start(ftu_t ftu, int motor)
{
ft_p ft = &ft_data[ftu];
fdc_p fdc = ft->fdc;
int s, mbits;
s = splbio();
DPRT(("tape_start start\n"));
/* reset, dma disable */
outb(fdc->baseport+FDOUT, 0x00);
(void)ftintr_wait(ftu, FTCMD_RESET, hz/10);
/* raise reset, enable DMA, motor on if needed */
if (motor)
mbits = (!ftu) ? FDO_MOEN0 : FDO_MOEN1;
else
mbits = 0;
outb(fdc->baseport+FDOUT, FDO_FRST | FDO_FDMAEN | mbits);
(void)ftintr_wait(ftu, FTCMD_RESET, hz/10);
splx(s);
tape_recal(ftu, 1);
/* set transfer speed */
outb(fdc->baseport+FDCTL, FDC_500KBPS);
DELAY(10);
DPRT(("tape_start end\n"));
}
/*
* Transfer control back to floppy disks.
*/
static void
tape_end(ftu_t ftu)
{
ft_p ft = &ft_data[ftu];
fdc_p fdc = ft->fdc;
int s;
DPRT(("tape_end start\n"));
tape_recal(ftu, 0);
s = splbio();
/* reset, dma disable */
outb(fdc->baseport+FDOUT, 0x00);
(void)ftintr_wait(ftu, FTCMD_RESET, hz/10);
/* raise reset, enable DMA */
outb(fdc->baseport+FDOUT, FDO_FRST | FDO_FDMAEN);
(void)ftintr_wait(ftu, FTCMD_RESET, hz/10);
splx(s);
/* set transfer speed */
outb(fdc->baseport+FDCTL, FDC_500KBPS);
DELAY(10);
fdc->flags &= ~FDC_TAPE_BUSY;
DPRT(("tape_end end\n"));
}
/*
* Wait for the driver to go inactive, cancel readahead if necessary.
*/
static void
tape_inactive(ftu_t ftu)
{
ft_p ft = &ft_data[ftu];
int s = splbio();
if (ft->segh != NULL) {
if (ft->segh->reqtype == FTIO_RDAHEAD) {
/* cancel read-ahead */
ft->segh->reqcan = 1;
} else if (ft->segh->reqtype == FTIO_WRITING && !ft->active) {
/* flush out any remaining writes */
DPRT(("Flushing write I/O chain\n"));
arq_state = ard_state = awr_state = 0;
ft->xblk = ft->segh->reqblk;
ft->xseg = ft->segh->reqseg;
ft->xcnt = 0;
ft->xptr = ft->segh->buff;
ft->active = 1;
timeout(ft_timeout, (caddr_t)ftu, 1);
}
}
while (ft->active) ftsleep(wc_iosts_change, 0);
splx(s);
}
/*
* Get the geometry of the tape currently in the drive.
*/
static int
ftgetgeom(ftu_t ftu)
{
int r, i, tries;
int cfg, qic80, ext;
int sts, fmt, len;
ft_p ft = &ft_data[ftu];
r = tape_status(ftu);
/* XXX fix me when format mode is finished */
if (r < 0 || (r & QS_CART) == 0 || (r & QS_FMTOK) == 0) {
DPRT(("ftgetgeom: no cart or not formatted 0x%04x\n",r));
ftg = NULL;
ft->newcart = 1;
return(0);
}
/* Report drive configuration */
for (cfg = -1, tries = 0; cfg < 0 && tries < 3; tries++)
cfg = qic_status(ftu, QC_CONFIG, 8);
if (tries == 3) {
DPRT(("ftgetgeom report config failed\n"));
ftg = NULL;
return(-1);
}
DPRT(("ftgetgeom report config got $%04x\n", cfg));
ft->lastcfg = cfg;
qic80 = cfg & QCF_QIC80;
ext = cfg & QCF_EXTRA;
/*
* XXX - This doesn't seem to work on my Colorado Jumbo 250...
* if it works on your drive, I'd sure like to hear about it.
*/
#if 0
/* Report drive status */
for (sts = -1, tries = 0; sts < 0 && tries < 3; tries++)
sts = qic_status(ftu, QC_TSTATUS, 8);
if (tries == 3) {
DPRT(("ftgetgeom report tape status failed\n"));
ftg = NULL;
return(-1);
}
DPRT(("ftgetgeom report tape status got $%04x\n", sts));
#else
/*
* XXX - Forge a fake tape status based upon the returned
* configuration, since the above command or code is broken
* for my drive and probably other older drives.
*/
sts = 0;
sts = (qic80) ? QTS_QIC80 : QTS_QIC40;
sts |= (ext) ? QTS_LEN2 : QTS_LEN1;
#endif
fmt = sts & QTS_FMMASK;
len = (sts & QTS_LNMASK) >> 4;
if (fmt > QCV_NFMT) {
ftg = NULL;
printf("ft%d: unsupported tape format\n", ftu);
return(-1);
}
if (len > QCV_NLEN) {
ftg = NULL;
printf("ft%d: unsupported tape length\n", ftu);
return(-1);
}
/* Look up geometry in the table */
for (i = 1; i < NGEOM; i++)
if (ftgtbl[i].g_fmtno == fmt && ftgtbl[i].g_lenno == len) break;
if (i == NGEOM) {
printf("ft%d: unknown tape geometry\n", ftu);
ftg = NULL;
return(-1);
}
ftg = &ftgtbl[i];
if (!ftg->g_trktape) {
printf("ft%d: unsupported format %s w/len %s\n",
ftu, ftg->g_fmtdesc, ftg->g_lendesc);
ftg = NULL;
return(-1);
}
DPRT(("Tape format is %s, length is %s\n", ftg->g_fmtdesc, ftg->g_lendesc));
ft->newcart = 0;
return(0);
}
/*
* Switch between tape/floppy. This will send the tape enable/disable
* codes for this drive's manufacturer.
*/
static int
set_fdcmode(dev_t dev, int newmode)
{
ftu_t ftu = FDUNIT(minor(dev));
ft_p ft = &ft_data[ftu];
fdc_p fdc = ft->fdc;
static int havebufs = 0;
int i;
SegReq *sp, *rsp;
if (newmode == FDC_TAPE_MODE) {
/* Wake up the tape drive */
switch (ft->type) {
case NO_TYPE:
fdc->flags &= ~FDC_TAPE_BUSY;
return(ENXIO);
case FT_NONE:
tape_start(ftu, 0);
break;
case FT_COLORADO:
tape_start(ftu, 0);
if (tape_cmd(ftu, QC_COL_ENABLE1)) {
tape_end(ftu);
return(EIO);
}
if (tape_cmd(ftu, QC_COL_ENABLE2 + ftu)) {
tape_end(ftu);
return(EIO);
}
break;
case FT_MOUNTAIN:
tape_start(ftu, 0);
if (tape_cmd(ftu, QC_MTN_ENABLE1)) {
tape_end(ftu);
return(EIO);
}
if (tape_cmd(ftu, QC_MTN_ENABLE2)) {
tape_end(ftu);
return(EIO);
}
break;
case FT_INSIGHT:
tape_start(ftu, 1);
break;
default:
DPRT(("ft%d: bad tape type\n", ftu));
return(ENXIO);
}
if (tape_status(ftu) < 0) {
if (ft->type == FT_COLORADO)
tape_cmd(ftu, QC_COL_DISABLE);
else if (ft->type == FT_MOUNTAIN)
tape_cmd(ftu, QC_MTN_DISABLE);
tape_end(ftu);
return(EIO);
}
/* Grab buffers from memory. */
if (!havebufs) {
ft->segh = ft->segt = NULL;
ft->doneh = ft->donet = NULL;
ft->segfree = NULL;
ft->hdr = NULL;
ft->nsegq = ft->ndoneq = ft->nfreelist = 0;
for (i = 0; i < FTNBUFF; i++) {
sp = malloc(sizeof(SegReq), M_DEVBUF, M_WAITOK);
if (sp == NULL) {
printf("ft%d: not enough memory for buffers\n", ftu);
for (sp=ft->segfree; sp != NULL; sp=sp->next)
free(sp, M_DEVBUF);
if (ft->type == FT_COLORADO)
tape_cmd(ftu, QC_COL_DISABLE);
else if (ft->type == FT_MOUNTAIN)
tape_cmd(ftu, QC_MTN_DISABLE);
tape_end(ftu);
return(ENOMEM);
}
sp->reqtype = FTIO_READY;
sp->next = ft->segfree;
ft->segfree = sp;
ft->nfreelist++;
}
/* take one buffer for header */
ft->hdr = ft->segfree;
ft->segfree = ft->segfree->next;
ft->nfreelist--;
havebufs = 1;
}
ft->io_sts = FTIO_READY; /* tape drive is ready */
ft->active = 0; /* interrupt driver not active */
ft->moving = 0; /* tape not moving */
ft->rdonly = 0; /* tape read only */
ft->newcart = 0; /* new cartridge flag */
ft->lastpos = -1; /* tape is rewound */
async_func = ACMD_NONE; /* No async function */
tape_state(ftu, 0, QS_READY, 60);
tape_cmd(ftu, QC_RATE);
tape_cmd(ftu, QCF_RT500+2); /* 500K bps */
tape_state(ftu, 0, QS_READY, 60);
ft->mode = FTM_PRIMARY;
tape_cmd(ftu, QC_PRIMARY); /* Make sure we're in primary mode */
tape_state(ftu, 0, QS_READY, 60);
ftg = NULL; /* No geometry yet */
ftgetgeom(ftu); /* Get tape geometry */
ftreq_rewind(ftu); /* Make sure tape is rewound */
} else {
if (ft->type == FT_COLORADO)
tape_cmd(ftu, QC_COL_DISABLE);
else if (ft->type == FT_MOUNTAIN)
tape_cmd(ftu, QC_MTN_DISABLE);
tape_end(ftu);
ft->newcart = 0; /* clear new cartridge */
if (ft->hdr != NULL) free(ft->hdr, M_DEVBUF);
if (havebufs) {
for (sp = ft->segfree; sp != NULL;) {
rsp = sp; sp = sp->next;
free(rsp, M_DEVBUF);
}
for (sp = ft->segh; sp != NULL;) {
rsp = sp; sp = sp->next;
free(rsp, M_DEVBUF);
}
for (sp = ft->doneh; sp != NULL;) {
rsp = sp; sp = sp->next;
free(rsp, M_DEVBUF);
}
}
havebufs = 0;
}
return(0);
}
/*
* Perform a QIC status function.
*/
static int
qic_status(ftu_t ftu, int cmd, int nbits)
{
int st3, r, i;
ft_p ft = &ft_data[ftu];
fdcu_t fdcu = ft->fdc->fdcu; /* fdc active unit */
if (tape_cmd(ftu, cmd)) {
DPRT(("ft%d: QIC status timeout\n", ftu));
return(-1);
}
/* Sense drive status */
out_fdc(fdcu, NE7CMD_SENSED);
out_fdc(fdcu, ftu);
st3 = in_fdc(fdcu);
if ((st3 & 0x10) == 0) { /* track 0 */
DPRT(("qic_status has dead drive... st3 = $%02x\n", st3));
return(-1);
}
for (i = r = 0; i <= nbits; i++) {
if (tape_cmd(ftu, QC_NEXTBIT)) {
DPRT(("ft%d: QIC status bit timed out on %d\n", ftu, i));
return(-1);
}
out_fdc(fdcu, NE7CMD_SENSED);
out_fdc(fdcu, ftu);
st3 = in_fdc(fdcu);
if (st3 < 0) {
DPRT(("ft%d: controller timed out on bit %d r=$%02x\n",
ftu, i, r));
return(-1);
}
r >>= 1;
if (i < nbits)
r |= ((st3 & 0x10) ? 1 : 0) << nbits;
else if ((st3 & 0x10) == 0) {
DPRT(("ft%d: qic status stop bit missing at %d, st3=$%02x r=$%04x\n",
ftu,i,st3,r));
return(-1);
}
}
DPRT(("qic_status returned $%02x\n", r));
return(r);
}
/*
* Open tape drive for use. Bounced off of Fdopen if tape minor is
* detected.
*/
int
ftopen(dev_t dev, int arg2) {
ftu_t ftu = FDUNIT(minor(dev));
fdc_p fdc;
/* check bounds */
if (ftu >= NFT)
return(ENXIO);
fdc = ft_data[ftu].fdc;
/* check for controller already busy with tape */
if (fdc->flags & FDC_TAPE_BUSY)
return(EBUSY);
/* make sure we found a tape when probed */
if (!(fdc->flags & FDC_HASFTAPE))
return(ENODEV);
fdc->fdu = ftu;
fdc->flags |= FDC_TAPE_BUSY;
return(set_fdcmode(dev, FDC_TAPE_MODE)); /* try to switch to tape */
}
/*
* Close tape and return floppy controller to disk mode.
*/
int
ftclose(dev_t dev, int flags)
{
ftu_t ftu = FDUNIT(minor(dev));
ft_p ft = &ft_data[ftu];
/* Wait for any remaining I/O activity to complete. */
tape_inactive(ftu);
ft->mode = FTM_PRIMARY;
tape_cmd(ftu, QC_PRIMARY);
tape_state(ftu, 0, QS_READY, 60);
ftreq_rewind(ftu);
return(set_fdcmode(dev, FDC_DISK_MODE)); /* Otherwise, close tape */
}
/*
* Perform strategy on a given buffer (not!). Changed so that the
* driver will at least return 'Operation not supported'.
*/
void
ftstrategy(struct buf *bp)
{
bp->b_error = ENODEV;
bp->b_flags |= B_ERROR;
biodone(bp);
}
/*
* Read or write a segment.
*/
static int
ftreq_rw(ftu_t ftu, int cmd, QIC_Segment *sr, struct proc *p)
{
int r, i;
SegReq *sp;
int s;
long blk, bad, seg;
unsigned char *cp, *cp2;
ft_p ft = &ft_data[ftu];
if (!ft->active && ft->segh == NULL) {
r = tape_status(ftu);
if ((r & QS_CART) == 0)
return(ENXIO); /* No cartridge */
if ((r & QS_FMTOK) == 0)
return(ENXIO); /* Not formatted */
tape_state(ftu, 0, QS_READY, 90);
}
if (ftg == NULL || ft->newcart) {
tape_inactive(ftu);
tape_state(ftu, 0, QS_READY, 90);
if (ftgetgeom(ftu) < 0)
return(ENXIO);
}
/* Write not allowed on a read-only tape. */
if (cmd == QIOWRITE && ft->rdonly)
return(EROFS);
/* Quick check of request and buffer. */
if (sr == NULL || sr->sg_data == NULL)
return(EINVAL);
/* Make sure requested track and segment is in range. */
if (sr->sg_trk >= ftg->g_trktape || sr->sg_seg >= ftg->g_segtrk)
return(EINVAL);
blk = sr->sg_trk * ftg->g_blktrk + sr->sg_seg * QCV_BLKSEG;
seg = sr->sg_trk * ftg->g_segtrk + sr->sg_seg;
s = splbio();
if (cmd == QIOREAD) {
/*
* See if the driver is reading ahead.
*/
if (ft->doneh != NULL ||
(ft->segh != NULL && ft->segh->reqtype == FTIO_RDAHEAD)) {
/*
* Eat the completion queue and see if the request
* is already there.
*/
while (ft->doneh != NULL) {
if (blk == ft->doneh->reqblk) {
sp = ft->doneh;
sp->reqtype = FTIO_READING;
sp->reqbad = sr->sg_badmap;
goto rddone;
}
segio_free(ft, ft->doneh);
}
/*
* Not on the completed queue, in progress maybe?
*/
if (ft->segh != NULL && ft->segh->reqtype == FTIO_RDAHEAD &&
blk == ft->segh->reqblk) {
sp = ft->segh;
sp->reqtype = FTIO_READING;
sp->reqbad = sr->sg_badmap;
goto rdwait;
}
}
/* Wait until we're ready. */
tape_inactive(ftu);
/* Set up a new read request. */
sp = segio_alloc(ft);
sp->reqcrc = 0;
sp->reqbad = sr->sg_badmap;
sp->reqblk = blk;
sp->reqseg = seg;
sp->reqcan = 0;
sp->reqtype = FTIO_READING;
segio_queue(ft, sp);
/* Start the read request off. */
DPRT(("Starting read I/O chain\n"));
arq_state = ard_state = awr_state = 0;
ft->xblk = sp->reqblk;
ft->xseg = sp->reqseg;
ft->xcnt = 0;
ft->xptr = sp->buff;
ft->active = 1;
timeout(ft_timeout, (caddr_t)ftu, 1);
rdwait:
ftsleep(wc_buff_done, 0);
rddone:
bad = sp->reqbad;
sr->sg_crcmap = sp->reqcrc & ~bad;
/* Copy out segment and discard bad mapped blocks. */
cp = sp->buff; cp2 = sr->sg_data;
for (i = 0; i < QCV_BLKSEG; cp += QCV_BLKSIZE, i++) {
if (bad & (1 << i)) continue;
copyout(cp, cp2, QCV_BLKSIZE);
cp2 += QCV_BLKSIZE;
}
segio_free(ft, sp);
} else {
if (ft->segh != NULL && ft->segh->reqtype != FTIO_WRITING)
tape_inactive(ftu);
/* Allocate a buffer and start tape if we're running low. */
sp = segio_alloc(ft);
if (!ft->active && (sp == NULL || ft->nfreelist <= 1)) {
DPRT(("Starting write I/O chain\n"));
arq_state = ard_state = awr_state = 0;
ft->xblk = ft->segh->reqblk;
ft->xseg = ft->segh->reqseg;
ft->xcnt = 0;
ft->xptr = ft->segh->buff;
ft->active = 1;
timeout(ft_timeout, (caddr_t)ftu, 1);
}
/* Sleep until a buffer becomes available. */
while (sp == NULL) {
ftsleep(wc_buff_avail, 0);
sp = segio_alloc(ft);
}
/* Copy in segment and expand bad blocks. */
bad = sr->sg_badmap;
cp = sr->sg_data; cp2 = sp->buff;
for (i = 0; i < QCV_BLKSEG; cp2 += QCV_BLKSIZE, i++) {
if (bad & (1 << i)) continue;
copyin(cp, cp2, QCV_BLKSIZE);
cp += QCV_BLKSIZE;
}
sp->reqblk = blk;
sp->reqseg = seg;
sp->reqcan = 0;
sp->reqtype = FTIO_WRITING;
segio_queue(ft, sp);
}
splx(s);
return(0);
}
/*
* Rewind to beginning of tape
*/
static int
ftreq_rewind(ftu_t ftu)
{
ft_p ft = &ft_data[ftu];
tape_inactive(ftu);
tape_cmd(ftu, QC_STOP);
tape_state(ftu, 0, QS_READY, 90);
tape_cmd(ftu, QC_SEEKSTART);
tape_state(ftu, 0, QS_READY, 90);
tape_cmd(ftu, QC_SEEKTRACK);
tape_cmd(ftu, 2);
tape_state(ftu, 0, QS_READY, 90);
ft->lastpos = -1;
ft->moving = 0;
return(0);
}
/*
* Move to logical beginning or end of track
*/
static int
ftreq_trkpos(ftu_t ftu, int req)
{
int curtrk, r, cmd;
ft_p ft = &ft_data[ftu];
tape_inactive(ftu);
tape_cmd(ftu, QC_STOP);
tape_state(ftu, 0, QS_READY, 90);
r = tape_status(ftu);
if ((r & QS_CART) == 0) return(ENXIO); /* No cartridge */
if ((r & QS_FMTOK) == 0) return(ENXIO); /* Not formatted */
if (ftg == NULL || ft->newcart) {
if (ftgetgeom(ftu) < 0) return(ENXIO);
}
curtrk = (ft->lastpos < 0) ? 0 : ft->lastpos / ftg->g_blktrk;
if (req == QIOBOT)
cmd = (curtrk & 1) ? QC_SEEKEND : QC_SEEKSTART;
else
cmd = (curtrk & 1) ? QC_SEEKSTART : QC_SEEKEND;
tape_cmd(ftu, cmd);
tape_state(ftu, 0, QS_READY, 90);
return(0);
}
/*
* Seek tape head to a particular track.
*/
static int
ftreq_trkset(ftu_t ftu, int *trk)
{
int r;
ft_p ft = &ft_data[ftu];
tape_inactive(ftu);
tape_cmd(ftu, QC_STOP);
tape_state(ftu, 0, QS_READY, 90);
r = tape_status(ftu);
if ((r & QS_CART) == 0) return(ENXIO); /* No cartridge */
if ((r & QS_FMTOK) == 0) return(ENXIO); /* Not formatted */
if (ftg == NULL || ft->newcart) {
if (ftgetgeom(ftu) < 0) return(ENXIO);
}
tape_cmd(ftu, QC_SEEKTRACK);
tape_cmd(ftu, *trk + 2);
tape_state(ftu, 0, QS_READY, 90);
return(0);
}
/*
* Start tape moving forward.
*/
static int
ftreq_lfwd(ftu_t ftu)
{
ft_p ft = &ft_data[ftu];
tape_inactive(ftu);
tape_cmd(ftu, QC_STOP);
tape_state(ftu, 0, QS_READY, 90);
tape_cmd(ftu, QC_FORWARD);
ft->moving = 1;
return(0);
}
/*
* Stop the tape
*/
static int
ftreq_stop(ftu_t ftu)
{
ft_p ft = &ft_data[ftu];
tape_inactive(ftu);
tape_cmd(ftu, QC_STOP);
tape_state(ftu, 0, QS_READY, 90);
ft->moving = 0;
return(0);
}
/*
* Set the particular mode the drive should be in.
*/
static int
ftreq_setmode(ftu_t ftu, int cmd)
{
int r;
ft_p ft = &ft_data[ftu];
tape_inactive(ftu);
r = tape_status(ftu);
switch(cmd) {
case QIOPRIMARY:
ft->mode = FTM_PRIMARY;
tape_cmd(ftu, QC_PRIMARY);
break;
case QIOFORMAT:
if (r & QS_RDONLY) return(ENXIO);
if ((r & QS_BOT) == 0) return(ENXIO);
tape_cmd(ftu, QC_FORMAT);
break;
case QIOVERIFY:
if ((r & QS_FMTOK) == 0) return(ENXIO); /* Not formatted */
tape_cmd(ftu, QC_VERIFY);
break;
}
tape_state(ftu, 0, QS_READY, 60);
return(0);
}
/*
* Return drive status bits
*/
static int
ftreq_status(ftu_t ftu, int cmd, int *sts, struct proc *p)
{
ft_p ft = &ft_data[ftu];
if (ft->active)
*sts = ft->laststs & ~QS_READY;
else
*sts = tape_status(ftu);
return(0);
}
/*
* Return drive configuration bits
*/
static int
ftreq_config(ftu_t ftu, int cmd, int *cfg, struct proc *p)
{
int r, tries;
ft_p ft = &ft_data[ftu];
if (ft->active)
r = ft->lastcfg;
else {
for (r = -1, tries = 0; r < 0 && tries < 3; tries++)
r = qic_status(ftu, QC_CONFIG, 8);
if (tries == 3) return(ENXIO);
}
*cfg = r;
return(0);
}
/*
* Return current tape's geometry.
*/
static int
ftreq_geom(ftu_t ftu, QIC_Geom *g)
{
tape_inactive(ftu);
if (ftg == NULL && ftgetgeom(ftu) < 0) return(ENXIO);
bcopy(ftg, g, sizeof(QIC_Geom));
return(0);
}
/*
* Return drive hardware information
*/
static int
ftreq_hwinfo(ftu_t ftu, QIC_HWInfo *hwp)
{
int tries;
int rom, vend;
tape_inactive(ftu);
bzero(hwp, sizeof(QIC_HWInfo));
for (rom = -1, tries = 0; rom < 0 && tries < 3; tries++)
rom = qic_status(ftu, QC_VERSION, 8);
if (rom > 0) {
hwp->hw_rombeta = (rom >> 7) & 0x01;
hwp->hw_romid = rom & 0x7f;
}
for (vend = -1, tries = 0; vend < 0 && tries < 3; tries++)
vend = qic_status(ftu, QC_VENDORID, 16);
if (vend > 0) {
hwp->hw_make = (vend >> 6) & 0x3ff;
hwp->hw_model = vend & 0x3f;
}
return(0);
}
/*
* Receive or Send the in-core header segment.
*/
static int
ftreq_hdr(ftu_t ftu, int cmd, QIC_Segment *sp)
{
ft_p ft = &ft_data[ftu];
QIC_Header *h = (QIC_Header *)ft->hdr->buff;
if (sp == NULL || sp->sg_data == NULL) return(EINVAL);
if (cmd == QIOSENDHDR) {
copyin(sp->sg_data, ft->hdr->buff, QCV_SEGSIZE);
} else {
if (h->qh_sig != QCV_HDRMAGIC) return(EIO);
copyout(ft->hdr->buff, sp->sg_data, QCV_SEGSIZE);
}
return(0);
}
/*
* I/O functions.
*/
int
ftioctl(dev_t dev, int cmd, caddr_t data, int flag, struct proc *p)
{
ftu_t ftu = FDUNIT(minor(dev));
switch(cmd) {
case QIOREAD: /* Request reading a segment from tape. */
case QIOWRITE: /* Request writing a segment to tape. */
return(ftreq_rw(ftu, cmd, (QIC_Segment *)data, p));
case QIOREWIND: /* Rewind tape. */
return(ftreq_rewind(ftu));
case QIOBOT: /* Seek to logical beginning of track. */
case QIOEOT: /* Seek to logical end of track. */
return(ftreq_trkpos(ftu, cmd));
case QIOTRACK: /* Seek tape head to specified track. */
return(ftreq_trkset(ftu, (int *)data));
case QIOSEEKLP: /* Seek load point. */
goto badreq;
case QIOFORWARD: /* Move tape in logical forward direction. */
return(ftreq_lfwd(ftu));
case QIOSTOP: /* Causes tape to stop. */
return(ftreq_stop(ftu));
case QIOPRIMARY: /* Enter primary mode. */
case QIOFORMAT: /* Enter format mode. */
case QIOVERIFY: /* Enter verify mode. */
return(ftreq_setmode(ftu, cmd));
case QIOWRREF: /* Write reference burst. */
goto badreq;
case QIOSTATUS: /* Get drive status. */
return(ftreq_status(ftu, cmd, (int *)data, p));
case QIOCONFIG: /* Get tape configuration. */
return(ftreq_config(ftu, cmd, (int *)data, p));
case QIOGEOM:
return(ftreq_geom(ftu, (QIC_Geom *)data));
case QIOHWINFO:
return(ftreq_hwinfo(ftu, (QIC_HWInfo *)data));
case QIOSENDHDR:
case QIORECVHDR:
return(ftreq_hdr(ftu, cmd, (QIC_Segment *)data));
}
badreq:
DPRT(("ft%d: unknown ioctl(%d) request\n", ftu, cmd));
return(ENXIO);
}
/*
* Not implemented
*/
int
ftdump(dev_t dev)
{
return(EINVAL);
}
/*
* Not implemented
*/
int
ftsize(dev_t dev)
{
return(EINVAL);
}
#endif
Reference in New Issue View Git Blame Copy Permalink