Bill Paul d25bb2d026 Modify the Adaptec "starfire" driver to reset the PHY on the MII bus ... before selecting a mode. The Seeq PHY chips on the Adaptec cards that use the AIC-6915 controller seem to need it in order to get them to change modes correctly. This corrects a problem that I noticed where my ANA-62022 board failed to correctly program the full duplex bit in the macconfig1 register when the interface was brought up. Running ifconfig sf0 would mask this problem in some cases because polling the PHY status would cause the miibus code to notice that full duplex was now needed and the statchg callback would be invoked to configure the duplex setting. However it would still get it wrong other times. Also changed sf_miibus_statchg() to program the IPG register to match the duplex setting in accordance with Adaptec manual's recommendations (0x15 for full duplex, 0x11 for half duplex).		1999-12-05 20:02:45 +00:00
..
adv_pci.c
adw_pci.c
ahc_pci.c
alpm.c	Remove the 'ivars' arguement to device_add_child() and	1999-12-03 08:41:24 +00:00
amd.c
amd.h
cy_pci.c
cy_pcireg.h
dc21040reg.h
ida_pci.c	Removal of sys/device.h	1999-10-05 21:19:41 +00:00
ide_pci.c
ide_pcireg.h
if_ar_p.c	Add support for the PCI version of the Digi SYNC/570i cards.	1999-10-17 09:40:04 +00:00
if_dc.c	Add the if_dc driver and remove all of the al, ax, dm, pn and mx drivers	1999-12-04 17:41:31 +00:00
if_dcreg.h	Add the if_dc driver and remove all of the al, ax, dm, pn and mx drivers	1999-12-04 17:41:31 +00:00
if_de.c
if_devar.h
if_en_pci.c
if_fpa.c
if_fxp.c
if_fxpreg.h
if_fxpvar.h
if_lnc_p.c
if_mn.c	Add NULL for new entrypoint.	1999-12-01 09:37:28 +00:00
if_rl.c	Fix usage of m_pullup().	1999-11-16 15:34:52 +00:00
if_rlreg.h	Make some tweaks to the RealTek driver:	1999-10-21 19:42:03 +00:00
if_sf.c	Modify the Adaptec "starfire" driver to reset the PHY on the MII bus	1999-12-05 20:02:45 +00:00
if_sfreg.h	Modify the Adaptec "starfire" driver to reset the PHY on the MII bus	1999-12-05 20:02:45 +00:00
if_sis.c
if_sisreg.h
if_sk.c
if_skreg.h
if_sr_p.c
if_ste.c
if_stereg.h
if_ti.c
if_tireg.h
if_tl.c
if_tlreg.h
if_tx.c	Added code to enable BusMaster operations.	1999-10-29 09:56:52 +00:00
if_txvar.h	Added code to enable BusMaster operations.	1999-10-29 09:56:52 +00:00
if_vr.c
if_vrreg.h
if_vx_pci.c
if_wb.c
if_wbreg.h
if_xl.c	Small tweak: just reset the transmit block instead of doing a global reset	1999-10-25 20:52:32 +00:00
if_xlreg.h	Make some small tweaks:	1999-10-14 21:49:17 +00:00
intpm.c	Remove the 'ivars' arguement to device_add_child() and	1999-12-03 08:41:24 +00:00
intpmreg.h
isp_pci.c	Fix dmasetup functions to have 16 bit queue indices. Get the chip revision	1999-11-21 02:56:17 +00:00
locate.pl
meteor_reg.h
meteor.c
ncr.c	Remove calls to alpha_register_pci_scsi(). After Mike's recent boot	1999-11-05 13:10:39 +00:00
ncrreg.h
ohci_pci.c	Remove the 'ivars' arguement to device_add_child() and	1999-12-03 08:41:24 +00:00
pccbb.c	Initial import of cardbus bridge driver (cbb) from the latest	1999-11-18 07:14:54 +00:00
pccbbreg.h	Initial import of cardbus bridge driver (cbb) from the latest	1999-11-18 07:14:54 +00:00
pccbbvar.h	Initial import of cardbus bridge driver (cbb) from the latest	1999-11-18 07:14:54 +00:00
pci_compat.c	* Implement bus_set/get/delete_resource for pci.	1999-10-14 21:38:33 +00:00
pci_if.m
pci_ioctl.h
pci.c	Raise the pci compat driver match priority a bit so that it's not	1999-12-05 18:50:22 +00:00
pcic_p.c	Add the PCI id for the TI PCI-1251B PCI-CardBus bridge.	1999-11-28 13:37:35 +00:00
pcic_p.h	Add the PCI id for the TI PCI-1251B PCI-CardBus bridge.	1999-11-28 13:37:35 +00:00
pcireg.h	Add the 16550 programming interface code for PCIS_SIMPLECOMM_UART.	1999-10-09 16:00:56 +00:00
pcisupport.c	Lower (a lot!) the chip* probe so it doesn't steal the pci ID from	1999-12-05 18:46:33 +00:00
pcivar.h	* Implement bus_set/get/delete_resource for pci.	1999-10-14 21:38:33 +00:00
scsiiom.c
simos.c
simos.h
ti_fw2.h
ti_fw.h
uhci_pci.c	Remove the 'ivars' arguement to device_add_child() and	1999-12-03 08:41:24 +00:00
xmaciireg.h
xrpu.c