invariant and APERF/MPERF MSRs exist but these MSRs never tick. When we
calculate effective frequency from cpu_est_clockrate(), it caused panic of
division-by-zero. Now we test whether these MSRs actually increase to avoid
such foot-shooting.
Reported by: dim
Tested by: dim
safer for i386 because it can be easily over 4 GHz now. More worse, it can
be easily changed by user with 'machdep.tsc_freq' tunable (directly) or
cpufreq(4) (indirectly). Note it is intentionally not used in performance
critical paths to avoid performance regression (but we should, in theory).
Alternatively, we may add "virtual TSC" with lower frequency if maximum
frequency overflows 32 bits (and ignore possible incoherency as we do now).
started to execute, it seems that the corresponding ISR bit in the "old"
local APIC can be cleared. This causes the local APIC interrupt routine
to fail to find an interrupt to service. Rather than panic'ing in this
case, simply return from the interrupt without sending an EOI to the
local APIC. If there are any other pending interrupts in other ISR
registers, the local APIC will assert a new interrupt.
Tested by: steve
bus_size_t may be 32 or 64 bits. Change the bounce_zone alignment field
to explicitly be 32 bits, as I can't really imagine a DMA device that
needs anything close to 2GB alignment of data.
interrupt in the I/O APIC before moving it to a different CPU. If the
interrupt had been triggered by the I/O APIC after locking icu_lock but
before we masked the pin in the I/O APIC, then this could cause the
interrupt to be pending on the "old" CPU and it would finally trigger
after we had moved the interrupt to the new CPU. This could cause us to
panic as there was no interrupt source associated with the old IDT vector
on the old CPU. Dropping the lock after the interrupt is masked but
before it is moved allows the interrupt to fire and be handled in this
case before it is moved.
Tested by: Daniel Braniss danny of cs huji ac il
MFC after: 1 week
the original amd64 and i386 headers with stubs.
Rename (AMD64|I386)_BUS_SPACE_* to X86_BUS_SPACE_* everywhere.
Reviewed by: imp (previous version), jhb
Approved by: kib (mentor)
- Avoid side-effect assignments in if statements when possible.
- Don't use ! to check for NULL pointers, explicitly check against NULL.
- Explicitly check error return values against 0.
- Don't use INTR_MPSAFE for interrupt handlers with only filters as it is
meaningless.
- Remove unneeded function casts.
Also, add a comment mentioning _PSD - on some systems it's enough to
put one logical CPU into a particular P-state to make other CPUs in
the same domain to enter that P-state.
Also, call sched_unbind() after the loop - sched_bind() automatically
rebinds from previous CPU to a new one, and the new arrangement of code
is safer against early loop exit.
Plus one minor style nit.
MFC after: 10 days
- Register APIC enumerators at SI_SUB_TUNABLES - 1 instead of SI_SUB_CPU - 1.
- Probe CPUs at SI_SUB_TUNABLES - 1. This allows i386 to set a truly
accurate mp_maxid value rather than always setting it to MAXCPU - 1.
local APIC if those LVT entries are valid. This quiets spurious illegal
register local APIC errors during boot on a CPU that doesn't support those
vectors.
MFC after: 1 week
- Use > 2^32 - 1 instead of >= when checking for memory regions above 4G.
- Skip SMAP entries > 4G on i386 rather than breaking out of the loop
since SMAP entries are not guaranteed to be in order.
- Remove 'i' and loop over 'rid' directly in the dump_avail[] case.
- Only check for 4G regions in the dump_avail[] case on i386 if PAE is
enabled since vm_paddr_t is 32-bit in the !PAE case.
Submitted by: alc
- Rename RES_BUS_SPACE_* into BUS_SPACE_* for consistency
- Trim out an unnecessary checking condition
Sponsored by: Sandvine Incorporated
Requested and reviewed by: jhb
