Tunables are now derived at boot time from maxusers. ie: change maxusers
via a tunable and all the derivative settings change. You can change
the other tunables individually as well. Even hz etc is tunable.
net.link.ether.bridge_refresh variables. While I'm here, try to
make some of the markup on this page more consistent with the
new (markup-reviewed) content.
PR: 22060
Reviewed by: ru (for markup, on an earlier version of this delta)
MFC after: 2 days
into addresses as we have no idea what address family they belong to.
When -n is not specified, resolve IPv6 as well as IPv4 addresses found
in the host field of utmp. Use realhostname_sa() to resolve addresses
(the old code was wrong).
Rename ``x'' to ``x_suffix'' to avoid confusion.
Hard code the host column width to 16 (against the imminent increase
of UT_HOSTSIZE in utmp.h).
making pcbs available to the outside world. otherwise, we will see
inpcb without ipsec security policy attached (-> panic() in ipsec.c).
Obtained from: KAME
MFC after: 3 days
were indices in a dense array. The cpuids are a sparse set and treat
them as such, setting up containers only for CPUs activated during
mb_init().
- Fix netstat(1) and systat(1) to treat the per-CPU stats area as a sparse
map, in accordance with the above.
This allows us to properly boot with certain CPUs disactivated. However, if
we later decide to re-activate said CPUs, we will barf until we decide to
implement CPU spinon/spinoff callback hooks to allow for said CPUs' per-CPU
containers to get configured on their activation.
Reported by: mjacob
Partially (sys/ diffs) Submitted by: mjacob
I revised the text after dd's kind review. So, if you find
any error, it is probably introduced by my last minutes'
update and is entirely my fault, not dd's.
Reviewed by: dd
This has supposedly been incorporated into the Intel code already, so this
will get cleanly replaced with the "official" version when it is next
imported and will not cause any conflicts or hiccups.
- Use sysctl to export stats
- Use ip_encap.c's encapsulation support
- Update lkm to kld (is 6 years a record for a broken module?)
- Remove some unused cruft
effect, which would cause unnecessary route deletion:
* Unfortunately, this has the obnoxious
* property of also triggering for insertion /above/ a pre-existing network
* route and clones. Sigh. This may be fixed some day.
The effect has been even worse, because recent versions of route.c set
the parent rtentry for cloned routes from an interface-direct route.
For example, suppose that we have an interface "ne0" that has an IPv4
subnet "10.0.0.0/24". Then we may have a cloned route like 10.0.0.1
on the interface, whose parent route is 10.0.0.0/24 (to the interface
ne0). Now, when we add the default route (i.e. 0.0.0.0/0),
rt_fixchange() will remove the cloned route 10.0.0.1. The (bad) effect
also prevents rt_setgate from configuring rt_gwroute, which would not
be an intended behavior.
As suggested in the comments to rt_fixchange(), we need stricter check
in the function, to prevent unintentional route deletion.
This fix also solve the "IPV6 panic?" problem in nd6_timer().
Submitted by: JINMEI Tatuya <jinmei@isl.rdc.toshiba.co.jp>
MFC after: 4 days
static entries with oid's over 100, and defining enough dynamic entries
causes an overlap.
Move the "magic" value 0x100 into <sys/sysctl.h> where it belongs.
PR: 29131
Submitted by: "Alexander N. Kabaev" <kabaev@mail.ru>
Reviewed by: -arch, -audit
MFC after: 2 weeks
