a) the configured default printer entry might turn out to become a security hole
Although lpd isn't enabled by default in FreeBSD 4 and later versions
bad things might happen because of a simple copy and paste failure:
- fill up root-fs, if /dev/lpt0 doesn't exist
- fill up the spool dir (either root-fs or var-fs) if machine hadn't been
designed as print server
Therefore best decision: if people want printing, then configure both
1. /etc/rc.conf
2. /etc/printcap
the default entry wouldn't have served well all tastes and needs anyway...
design of most of our config files is, to have commented out suggestions
if a service is not active.
b) [Garance]
fix old and wrong documentation:
input filters are possible even if you print to a remote printer
this makes FreeBSDs implementation of lpd currently the best without
having to switch to port monster LPRng ...
c) fix pointer to wrong handbook section for a longer time .. so I doesn't fix the number
I'm only referring to the printing section, otherwise this would have to be fixed several
times, if the chapters should be reordered again ...
d) typo: chose -> choose
Submitted by: me and some suggestions by Garance
Approved by: Eivind and Garance A Drosihn <drosih@rpi.edu> in private e-mail
* Use a sub-section (Ss) instead of a section (Sh) for
"Sysctl MIB Entries".
* Use a tagged list (Bl, El and It) instead of sub-sections (Ss) for
the actual MIB entries.
* Mark paths up as such (Pa).
* Mark defined values up as such (Dv).
of files auto-installed during an upgrade from a really old system
can get quite long, and it's piped to the PAGER already, print
that first, then print any of the 4 two-line messages that might
apply.
Return ENOTSUP for any opcode that is not supported by the XPT
device.
Add back a missing local declaration that seems to have been deleted
by my last commit.
which have long names. Instead of just listing '...', try to list some
reasonable subset of the name (with a "..." to indicate something missing).
Reviewed by: freebsd-print@bostonradio.org (only a little review)
Filter incoming transfer negotiation requests to ensure they
never exceed the settings specified by the user.
In restart sequencer attempt to deal with a bug in the aic7895.
If a third party reset occurs at just the right time, the
stack register can lock up. When restarting the sequencer
after handling the SCSI reset, poke SEQADDR1 before resting
the sequencers program counter.
When something strange happens, dump the card's transaction
state via ahc_dump_card_state(). This should aid in debugging.
Handle request sense transactions via the QINFIFO instead of
attaching them to the waiting queue directly. The waiting
queue consumes card SCB resources and, in the pathological case
of every target on the bus beating our selection attemps and
issuing a check condition, could have caused us to run out
of SCBs. I have never seen this happen, and only early
cards with 3 or 4 SCBs had any real chance of ever getting
into this state.
Add additional sequencer interrupt codes to support firmware
diagnostics. The diagnostic code is enabled with the
AHC_DEBUG_SEQUENCER kernel option.
Make it possible to switch into and out of target mode on
the fly. The card comes up by default as an initiator but
will switch into target mode as soon as an enable lun operation
is performed. As always, target mode behavior is gated
by the AHC_TMODE_ENABLE kernel option so most users will
not be affected by this change.
In ahc_update_target_msg_request(), also issue a new
request if the ppr_options have changed.
Never issue a PPR as a target. It is forbidden by the spec.
Correct a bug in ahc_parse_msg() that prevented us from
responding to PPR messages as a target.
Mark SCBs that are on the untagged queue with a flag instead
of checking several fields in the SCB to see if the SCB should
be on the queue. This makes it easier for things like automatic
request sense requests to be queued without touching the
untagged queues even though they are untagged requests.
When dealing with ignore wide residue messages that occur
in the middle of a transfer, reset HADDR, not SHADDR for
non-ultra2 chips. Although SHADDR is where the firmware
fetches the ending transfer address for a save data pointers
request, it is readonly. Setting HADDR has the side effect
of also updating SHADDR.
Cleanup the output of ahc_dump_card_state() by nulling out the
free scb list in the non-paging case. The free list is only
used if we must page SCBs.
Correct the transmission of cdbs > 12 bytes in length. When
swapping HSCBs prior to notifing the sequencer of the new
transaction, the bus address pointer for the cdb must also
be recalculated to reflect its new location. We now defer
the calculation of the cdb address until just before queing
it to the card.
When pulling transfer negotiation settings out of scratch
ram, convert 5MHz/clock doubled settings to 10MHz.
Add a new function ahc_qinfifo_requeue_tail() for use by
error recovery actions and auto-request sense operations.
These operations always occur when the sequencer is paused,
so we can avoid the extra expense incurred in the normal
SCB queue method.
Use the BMOV instruction for all single byte moves on
controllers that support it. The bmov instruction is
twice as fast as an AND with an immediate of 0xFF as
is used on older controllers.
Correct a few bugs in ahc_dump_card_state(). If we have
hardware assisted queue registers, use them to get the
sequencer's idea of the head of the queue. When enumerating
the untagged queue, it helps to use the correct index for
the queue.
aic7xxx.h:
Indicate via a feature flag, which controllers can take
on both the target and the initiator role at the same time.
Add the AHC_SEQUENCER_DEBUG flag.
Add the SCB_CDB32_PTR flag used for dealing with cdbs
with lengths between 13 and 32 bytes.
Add new prototypes.
aic7xxx.reg:
Allow the SCSIBUSL register to be written to. This is
required to fix a selection timeout problem on the 7892/99.
Cleanup the sequencer interrupt codes so that all debugging
codes are grouped at the end of the list.
Correct the definition of the ULTRA_ENB and DISC_DSB locations
in scratch ram. This prevented the driver from properly honoring
these settings when no serial eeprom was available.
Remove an unused sequencer flag.
aic7xxx.seq:
Just before a potential select-out, clear the SCSIBUSL
register. Occasionally, during a selection timeout, the
contents of the register may be presented on the bus,
causing much confusion.
Add sequencer diagnostic code to detect software and or
hardware bugs. The code attempts to verify most list
operations so any corruption is caught before it occurs.
We also track information about why a particular reconnection
request was rejected.
Don't clobber the digital REQ/ACK filter setting in SXFRCTL0
when clearing the channel.
Fix a target mode bug that would cause us to return busy
status instead of queue full in respnse to a tagged transaction.
Cleanup the overrun case. It turns out that by simply
butting the chip in bitbucket mode, it will ack any
bytes until the phase changes. This drasticaly simplifies
things.
Prior to leaving the data phase, make sure that the S/G
preload queue is empty.
Remove code to place a request sense request on the waiting
queue. This is all handled by the kernel now.
Change the semantics of "findSCB". In the past, findSCB
ensured that a freshly paged in SCB appeared on the disconnected
list. The problem with this is that there is no guarantee that
the paged in SCB is for a disconnected transation. We now
defer any list manipulation to the caller who usually discards
the SCB via the free list.
Inline some busy target table operations.
Add a critical section to protect adding an SCB to
the disconnected list.
aic7xxx_freebsd.c:
Handle changes in the transfer negotiation setting API
to filter incoming requests. No filtering is necessary
for "goal" requests from the XPT.
Set the SCB_CDB32_PTR flag when queing a transaction with
a large cdb.
In ahc_timeout, only take action if the active SCB is
the timedout SCB. This deals with the case of two
transactions to the same device with different timeout
values.
Use ahc_qinfifo_requeu_tail() instead of home grown
version.
aic7xxx_inline.h:
Honor SCB_CDB32_PTR when queuing a new request.
aic7xxx_pci.c:
Use the maximum data fifo threshold for all chips.
The XPT uses this to prevent tags from being used on parallel SCSI
interfaces immediately after a bus reset or BDR so that controllers
have an oportunity to renegotiate without tag messages in the way.
Somehow this got disabled... the functionality has been here for
quite some time.
Noticed by: my SCSI bus analyzer
