Also save the DAC state, increase the maximum save state size from
4k to 8k, and refuse to save the VESA state if the BIOS reports it
is larger than the maximum size we can handle.
It doesn't appear that anything currently uses this code, but it
turns out to be capable of restoring some notebook displays to a
working state after a suspend-resume cycle.
SMP systems. It appears all drivers except ichss should attach to each
CPU and that settings should be performed on each CPU. Add comments about
this. Also, add a guard for p4tcc's identify method being called more than
once.
a bugfix of clearing the On-Demand flag when going back to 100%. It
has been tested and works on an IBM R32. Note original work done by
Ted Unangst and sobomax@.
IRQ 0 and not an ExtINT pin. The MADT enumerators ignore the PC-AT flag
and ignore overrides that map IRQ 0 to pin 2 when this quirk is present.
- Add a block comment above the quirks to document each quirk so that we
can use more verbose descriptions quirks.
MFC after: 2 weeks
ACPI MADT only does if the PC-AT flag is set), then don't assume that pin 0
on the first I/O APIC is an ExtINT pin. Instead, assume that it is ISA
IRQ 0.
on the previous generation of Pentium-M processors (Banias). Support for
Dothan and later processors involves working with acpi_perf(4) to extract
information about supported states. This driver should work on MP systems
including HTT. It is experimental and may have a few bugs but has been
tested to not crash at least.
Thanks to Colin Percival for his initial work on this driver.
preliminary support for using the GCC-compatibility of ICC was committed
but couldn't be tested at that time due to problems with ICC itself. Since
ICC 8.1 it's possible to use its GCC-compatibility under FreeBSD and it
turned out that a typedef for __gnuc_va_list is required in that case.
Revert the part of rev. 1.8 which #ifdef'ed out __gnuc_va_list for ICC.
MFC after: 1 week
parent cpu device before passing it to pcpu_find(). Get the ivars from the
child, not parent cpu device. These bugs would cause a panic when
dereferencing the pcpu ivar, but weren't present in the acpi attachment
which it seems most people are using.
former is callable from user space and the latter from the kernel one. Make
kernel version take additional argument which tells if the respective call
should check for additional restrictions for sending signals to suid/sugid
applications or not.
Make all emulation layers using non-checked version, since signal numbers in
emulation layers can have different meaning that in native mode and such
protection can cause misbehaviour.
As a result remove LIBTHR from the signals allowed to be delivered to a
suid/sugid application.
Requested (sorta) by: rwatson
MFC after: 2 weeks
and wd80x3 support. Make the obscure ISA cards optional, and add
those options to NOTES on i386 (note: the ifdef around the whole code
is for module building). Tweak pc98 ed support to include wd80x3 too.
Add goo for alpha too.
The affected cards are the 3Com 3C503, HP LAN+ and SIC (whatever that
is). I couldn't find any of these for sale on ebay, so they are
untested. If you have one of these cards, and send it to me, I'll
ensure that you have no future problems with it...
Minor cleanups as well by using functions rather than cut and paste
code for some probing operations (where the function call overhead is
lost in the noise).
Remove use of kvtop, since they aren't required anymore. This driver
needs to get its memory mapped act together, however, and use bus
space. It doesn't right now.
This reduces the size of if_ed.ko from about 51k to 33k on my laptop.
which will help to debug hangs on boot.
- Remove 'U' from debug.watchdog sysctl definition, so if we set it to '-1'
it really shows '-1'.
- Fix comment.
Reviewed by: rwatson
rather than forwarding interrupts from the clock devices around using IPIs:
- Add an IDT vector that pushes a clock frame and calls
lapic_handle_timer().
- Add functions to program the local APIC timer including setting the
divisor, and setting up the timer to either down a periodic countdown
or one-shot countdown.
- Add a lapic_setup_clock() function that the BSP calls from
cpu_init_clocks() to setup the local APIC timer if it is going to be
used. The setup uses a one-shot countdown to calibrate the timer. We
then program the timer on each CPU to fire at a frequency of hz * 3.
stathz is defined as freq / 23 (hz * 3 / 23), and profhz is defined as
freq / 2 (hz * 3 / 2). This gives the clocks relatively prime divisors
while keeping a low LCM for the frequency of the clock interrupts.
Thanks to Peter Jeremy for suggesting this approach.
- Remove the hardclock and statclock forwarding code including the two
associated IPIs. The bitmap IPI handler has now effectively degenerated
to just IPI_AST.
- When the local APIC timer is used we don't turn the RTC on at all, but
we still enable interrupts on the ISA timer 0 (i8254) for timecounting
purposes.
the semantics in that the returned filename to use is now a kernel
pointer rather than a user space pointer. This required changing the
arguments to the CHECKALT*() macros some and changing the various system
calls that used pathnames to use the kern_foo() functions that can accept
kernel space filename pointers instead of calling the system call
directly.
- Use kern_open(), kern_access(), kern_execve(), kern_mkfifo(), kern_mknod(),
kern_setitimer(), kern_getrusage(), kern_utimes(), kern_unlink(),
kern_chdir(), kern_chmod(), kern_chown(), kern_symlink(), kern_readlink(),
kern_select(), kern_statfs(), kern_fstatfs(), kern_stat(), kern_lstat(),
kern_fstat().
- Drop the unused 'uap' argument from spx_open().
- Replace a stale duplication of vn_access() in xenix_access() lacking
recent additions such as MAC checks, etc. with a call to kern_access().
reboot. Safter the reboot the TCC is usually in the Automatic mode, in which
reading current performance level is likely to produce bogus results make sure
to switch it to the On-Demand mode and set to some known performance level.
Unfortunately there is no reliable way to check that TCC is in the Automatic
mode. Reading bit 4 of ACPI Thermal Monitor Control Register produces 0
regardless of the current mode.
MFC after: 1 week
uses the i8237 without trying to emulate the PC architecture move
the register definitions for the i8237 chip into the central include
file for the chip, except for the PC98 case which is magic.
Add new isa_dmatc() function which tells us as cheaply as possible
if the terminal count has been reached for a given channel.
devclass. As pointed out by dfr@, devclasses don't have to share the same
linkage if multiple drivers have the same name. Newbus should match the
devclasses based on name and allocate non-conflicting unit numbers.
millisecond it is calibrating. Suggested by jhb@ and bde@. Don't clobber
the tsc_freq with the new value since it isn't accurate enough for
timecounters and the timecounter system as a whole needs support for
changing rates before we do this. Subtract 0.5% from our measurement
to account for overhead in DELAY. Note that this interface is for
estimating the clockrate and needs to work well at runtime so doing a full
calibration including disabling interrupts for a second is not feasible.
interrupts, read from the interrupt status register to clear any pending
interrupts. Otherwise in some rare cases the RTC would never fire any
interrupts as it constantly thinks it has an interrupt pending.
PR: i386/17800
PR: kern/76776
Submitted by: Jose M. Alcaide jose at we dot lc dot ehu dot es
MFC after: 2 weeks
copies arguments into the kernel space and one that operates
completely in the kernel space;
o use kernel-only version of execve(2) to kill another stackgap in
linuxlator/i386.
Obtained from: DragonFlyBSD (partially)
MFC after: 2 weeks
i386_{get,set}_ioperm() and make those APIs visible in the kernel namespace;
o use i386_{get,set}_ldt() and i386_{get,set}_ioperm() instead of sysarch()
in the linuxlator, which allows to kill another two stackgaps.
MFC after: 2 weeks
interrupts that have a trigger mode of conforming. This fixes problems on
some older machines that still route PCI devices via ISA interrupts when
using an I/O APIC.
Tested by: Peter Trifonov pvtrifonov at mail dot ru
MFC after: 1 month
instead of burying that in the atpic(4) code as atpic(4) is not the only
user of elcr(4). Change the elcr(4) code to export a global elcr_found
variable that other code can check to see if a valid ELCR was found.
MFC after: 1 month
(calling a __dead2 function such as panic() at the end of a function), the
saved %eip on the stack will actually not be part of the function that
executed a call instruction but instead will be the first instruction of
the next function in the text. This happens with dblfault_handler() and
syscall() for example. Work around this in the one place it matters by
looking at the saved %eip - 1 to determine the calling function when we
check for "magic" frames.
MFC after: 2 weeks
interrupt is wired up to all the I/O APICs in the system. If the system
has only one I/O APIC, then just act as if the entry specified that APIC.
We still don't try to handle global entries in a system with multiple I/O
APICs.
Tested by: Peter Trifonov pvtrifonov at mail dot ru
MFC after: 1 week
- Fix the MP Table pci bridge drivers to not probe the configuration table
unless we actually have one. Machines using a default configuration do
not have such a table.
- Only allow default configuration types of 5 (ISA + PCI) and 6 (EISA +
PCI) as the others are not likely to work. Types 1 through 4 use an
external APIC (probably with 80486 processors) which we certainly do not
support, and type 7 uses an MCA bus which has not been tested with the
new MP Table code.
- Correct the fact that the single I/O APIC in a default configuration has
an ID of 2, not 0.
- Fix off by one errors in setting the bus types from the default_data[]
arrays for default configurations.
- Explicitly configure each of the 16 interrupt pins on the sole I/O APIC
when using a default configuration. This is especially helpful for type
6 (EISA + PCI) since the EISA interrupts need to have their polarity
programmed based on the values in the ELCR.
Much thanks to the submitter and tester who endured several rounds of
testing to get this fixed.
MFC after: 1 week
Tested by: Georg Schwarz georg dot schwarz at freenet dot de
cuts to the chase and fills in a provided s/g list. This is meant to optimize
out the cost of the callback since the callback doesn't serve much purpose for
mbufs since mbuf loads will never be deferred. This is just for amd64 and
i386 at the moment, other arches will be coming shortly.
from 4.x kernel config files. User's wishing to upgrade from 4.x to 6
will need to go through 5.x, or grab this script from there. These
scripts will remain in RELENG_5...
other comments. Clarify that the next two things needed for SMP are
two lines.
- Expand mii abbreviation to miibus for clarity in the USB ethernet
comment.
system from an AP at runtime (i.e., calling cpu_reset from ddb). Someday,
if we move to an NMI for stopping cpus instead, we can do away with this.
Requested by: jhb
though these aren't used yet.
- Add missing function prototypes for some static functions.
- Allow lvt_mode() to handle an LVT entry with a delivery mode of fixed.
- Consolidate code duplicated in lapic_init() and lapic_setup() to program
the spurious vector register of a local APIC in a static lapic_enable()
function.
- Dump the timer, thermal, error, and performance counter LVT entries
during lapic_dump().
- Program LVT pins (currently only LINT0 and LINT1) after the local
APIC has been software enabled via lapic_enable() since otherwise the
LVT programming will not be able to unmask LVT sources.
on entry and it assumes the responsibility for releasing the page queues
lock if it must sleep.
Remove a bogus comment from pmap_enter_quick().
Using the first change, modify vm_map_pmap_enter() so that the page queues
lock is acquired and released once, rather than each time that a page
is mapped.
Currently this is only used to initiailize the TPR to 0 during initial
setup.
- Reallocate vectors for the local APIC timer, error, and thermal LVT
entries. The timer entry is allocated from the top of the I/O interrupt
range reducing the number of vectors available for hardware interrupts
to 191. Linux happens to use the same exact vector for its timer
interrupt as well. If the timer vector shared the same priority queue
as the IPI handlers, then the frequency that the timer vector will
eventually be firing at can interact badly with the IPIs resulting in
the queue filling and the dreaded IPI stuck panics, hence it being located
at the top of the previous priority queue instead.
- Fixup various minor nits in comments.
In such cases, the busying of the page and the unlocking of the
containing object by vm_map_pmap_enter() and vm_fault_prefault() is
unnecessary overhead. To eliminate this overhead, this change
modifies pmap_enter_quick() so that it expects the object to be locked
on entry and it assumes the responsibility for busying the page and
unlocking the object if it must sleep. Note: alpha, amd64, i386 and
ia64 are the only implementations optimized by this change; arm,
powerpc, and sparc64 still conservatively busy the page and unlock the
object within every pmap_enter_quick() call.
Additionally, this change is the first case where we synchronize
access to the page's PG_BUSY flag and busy field using the containing
object's lock rather than the global page queues lock. (Modifications
to the page's PG_BUSY flag and busy field have asserted both locks for
several weeks, enabling an incremental transition.)
the ISA and CBUS (called isa on pc98) attachments. Eliminate all PC98
ifdefs in the process (the driver in pc98/pc98/mse.c was a copy of the one
in i386/isa/mse.c with PC98 ifdefs). Create a module for this driver.
I've tested this my PC-9821RaS40 with moused. I've not tested this on i386
because I have no InPort cards, or similar such things. NEC standardized
on bus mice very early, long before ps/2 mice ports apeared, so all PC-98
machines supported by FreeBSD/pc98 have bus mice, I believe.
Reviewed by: nyan-san
between object code generated without the flag but it makes sense and might
make a difference in the future.
PR: kern/53008
Submitted by: Jens Rehsack rehsack at liwing de
stepped the process to the system call), we need to clear the trap flag
from the new frame unless the debugger had set PF_FORK on the parent.
Otherwise, the child will receive a (likely unexpected) SIGTRAP when it
executes the first instruction after returning to userland.
Reviewed by: bde
MFC after: 3 days
as this may cause deadlocks.
This should fix kern/72123.
Discussed with: jhb
Tested by: Nik Azim Azam, Andy Farkas, Flack Man, Aykut KARA
Izzet BESKARDES, Jens Binnewies, Karl Keusgen
Approved by: sam (mentor)
These devices should be probed first because they are at fixed
locations and cannot be turned off. ISA PNP devices, on the other
hand, can be turned off and often can be flexible in the resources
they use. Probe them last, as always.
actually is a property of the northbridge and applies to all PCI/PCI-X/PCIe
devices in the system, though only PCIe devices will respond to registers
higher than 256. This uses per-CPU pools of temporary mappings so that
the whole 256MB of configuration space doesn't have to be mapped all at
once. While the sf_buf API was considered for this, the fact that it
requires sleep locks and can return failure made it unsuitable for this use.
For now only the Intel Grantsdale and Lindenhurst (925 and 752x) chipsets are
supported. Since there doesn't appear to be a compatible way to determine
northbridge support, new chipsets will have to be explicitely added in the
future.
specified register, but a pointer to the in-memory representation of
that value. The reason for this is twofold:
1. Not all registers can be represented by a register_t. In particular
FP registers fall in that category. Passing the new register value
by reference instead of by value makes this point moot.
2. When we receive a G or P packet, both are for writing a register,
the packet will have the register value in target-byte order and
in the memory representation (modulo the fact that bytes are sent
as 2 printable hexadecimal numbers of course). We only need to
decode the packet to have a pointer to the register value.
This change fixes the bug of extracting the register value of the P
packet as a hexadecimal number instead of as a bit array. The quick
(and dirty) fix to bswap the register value in gdb_cpu_setreg() as
it has been added on i386 and amd64 can therefore be removed and has
in fact been that.
Tested on: alpha, amd64, i386, ia64, sparc64
Consolidate all of the bounce tests into the BUS_DMA_COULD_BOUNCE flag.
Allocate the bounce zone at either tag creation or map creation to help
avoid null-pointer derefs later on. Track total pages per zone so that
each zone can get a minimum allocation at tag creation time instead of
being defeated by mis-behaving tags that suck up the max amount.
i386 to dev/acpi_support. In theory, these devices could be found
other than in i386 machines only as amd64 becomes more popular. These
drivers don't appear to do anything i386 specific, so move them to
dev/acpi_support. Move config lines to files so that those
architectures that don't support kernel modules can build them into
the kernel. At the same time, rename acpi_snc to acpi_sony to follow
the lead of all the other specialty devices.
models of laptops, which are essentially the same as the normal
ones, as far as acpi_asus is concerned[1]
o Use the above as an excuse to reshuffle the mess I made of the
probe function when I originally wrote it.
Reported by: Soeren Larsen <soeren@whiteswan.dk>
of atomic_store_rel().
- Use the 80386 versions of atomic_load_acq() and atomic_store_rel() that
do not use serializing instructions on all UP kernels since a UP machine
does need to synchronize with other CPUs. This trims lots of cycles from
spin locks on UP kernels among other things.
Benchmarked by: rwatson
appropriate for different tag requirements. With the former global pool,
bounce pages might get allocated that are appropriate for one tag, but not
appropriate for another, but the system had no way to distinguish between them.
Now zones with distinct attributes are created to hold pages, and each tag
that requires bouncing is associated with a zone. New zones are created as
needed if no existing zones can meet the requirements of the tag. Stats for
each zone are tracked via the hw.busdma sysctl node.
This should help drivers that are failing with mysterious data corruption.
MFC After: 1 week
Change the spelling of the "catch" option to be consistent with the new
options. Implement the "no wait" option. An implementation of the "CPU
private" for i386 will be committed at a later date.
Expose some of the amd64-specific sysarch functions to allow alternative
implementations of the %fs/%gs code for TLS, threads, etc. USER_LDT does
not exist on the amd64 kernel, so we have to implement things other ways.
control the number of lines per page rather than a constant. The variable
can be examined and changed in ddb as '$lines'. Setting the variable to
0 will effectively turn off paging.
- Change db_putchar() to force out pending whitespace before outputting
newlines and carriage returns so that one can rub out content on the
current line via '\r \r' type strings.
- Change the simple pager to rub out the --More-- prompt explicitly when
the routine exits.
- Add some aliases to the simple pager to make it more compatible with
more(1): 'e' and 'j' do a single line. 'd' does half a page, and
'f' does a full page.
MFC after: 1 month
Inspired by: kris
the final set of traces -- someone with more busdma background
will probably want to review and expand this, as well as port to
other platforms. This tracing is sufficient to identify key
busdma events on i386, and in particular to draw attention to
bounce buffering events that may have a substantial performance
impact.
modes on a tty structure.
Both the ".init" and the current settings are initialized allowing
the function to be used both at attach and open time.
The function takes an argument to decide if echoing should be enabled.
Echoing should not be enabled for regular physical serial ports
unless they are consoles, in which case they should be configured
by ttyconsolemode() instead.
Use the new function throughout.
invalidate the TLB(s) if the old mapping wasn't used by the CPU. With
network interfaces that implement checksum off-loading, the old mapping is
almost never used by the CPU, only by the device driver for setting up the
DMA operation.
Reviewed by: tegge@
Restructure pmap_enter() to prevent the loss of a page modified (PG_M) bit
in a race between processors. (This restructuring assumes the newly atomic
pte_load_store() for correct operation.)
Reviewed by: tegge@
PR: i386/61852
RAM. Many older, legacy bridges only allow allocation from this
range. This only appies to devices who don't have their memory
assigned by the BIOS (since we allocate the ranges so assigned
exactly), so should have minimal impact.
Hoewver, for CardBus bridges (cbb), they rarely get the resources
allocated by the BIOS, and this patch helps them greatly. Typically
the 'bad Vcc' messages are caused by this problem.
that is no longer required. (In fact, it is not clear that it was ever
required in HEAD or RELENG_4, only RELENG_3 required a work-around.) Now,
as before revision 1.251, if the preexisting PTE is invalid, pmap_enter()
does not call pmap_invalidate_page() to update the TLB(s).
Note: Even with this change, the handling of a copy-on-write fault is
inefficient, in such cases pmap_enter() calls pmap_invalidate_page() twice.
Discussed with: bde@
PR: kern/16568
need to mask off the page offset bits. (This operation made some sense
prior to i386/i386/pmap.c revision 1.254 when we passed a physical address
rather than a vm_page pointer to pmap_enter().)
uses predate the change in the pmap_enter() interface that replaced the
page's physical address by the address of its vm_page structure. The
PHYS_TO_VM_PAGE() was being used to compute the address of the same vm_page
structure that was being passed in.
1. Process p1 is currently being swapped in.
2. Process p2 calls linux_ptrace(PTRACE_GETFPXREGS, p1_pid, ...)
3. After acquiring a reference to FIRST_THREAD_IN_PROC(p1),
p2 blocks in faultin() while p1 finishes being swapped in.
This means p2 won't get back the lock on p1 until after p1's
threads are runnable.
4. After p1 is swapped in, the first thread in p1 exits.
5. p2 now uses its dangling reference to p1's first thread.
pmap_copy(). This entails additional locking in pmap_copy() and the
addition of a "flags" parameter to the page table page allocator for
specifying whether it may sleep when memory is unavailable. (Already,
pmap_copy() checks the availability of memory, aborting if it is scarce.
In theory, another CPU could, however, allocate memory between
pmap_copy()'s check and the call to the page table page allocator,
causing the current thread to release its locks and sleep. This change
makes this scenario impossible.)
Reviewed by: tegge@
multiprocessors. Specifically, the error is conditioning the call to
pmap_invalidate_page() on whether the pmap is active on the current CPU.
This call must be unconditional. Regardless of whether the pmap is active
on the CPU performing _pmap_unwire_pte_hold(), it could be active on another
CPU. For example, a call to pmap_remove_all() by the page daemon could
result in a call to _pmap_unwire_pte_hold() with the pmap inactive on the
current CPU and active on another CPU. In such circumstances, failing to
call pmap_invalidate_page() results in a stale TLB entry on the other CPU
that still maps the now deallocated page table page. What happens next is
typically a mysterious panic in pmap_enter() by the other CPU, either
"pmap_enter: attempted pmap_enter on 4MB page" or "pmap_enter: pte vanished,
va: 0x%lx". Both occur because the former page table page has been recycled
and allocated to a new purpose. Consequently, it no longer contains zeroes.
See also Peter's i386/i386/pmap.c revision 1.448 and the related e-mail
thread last year.
Many thanks to the engineers at Sandvine for providing clear and concise
information until all of the pieces of the puzzle fell into place and
for testing an earlier patch.
MT5 Candidate
a stack trace from ddb, the output will pause with a '--More--' prompt
every 18 lines. If you hit Enter, it will print another line and prompt
again. If you hit space it will output another page and then prompt.
If you hit 'q' or 'x' it will abort the rest of the stack trace.
- Fix the sparc64 userland stack trace to honor the total count of lines
to print. This is useful if your trace happens to walk back onto
0xdeadc0de and gets stuck in an endless loop.
MFC after: 1 month
Tested on: i386, alpha, sparc64
the page table page's wired count rather than its hold count to contain
the reference count. My rationale for this change is based on several
factors:
1. The machine-independent and pmap layers used the same hold count field
in subtly different ways. The machine-independent layer uses the hold
count to implement a form of ephemeral wiring that is used by pipes,
physio, etc. In other words, subsystems where we wish to temporarily
block a page from being swapped out while it is mapped into the kernel's
address space. Such pages are never removed from the page queues.
Instead, the page daemon recognizes a non-zero hold count to mean "hands
off this page." In contrast, page table pages are never in the page
queues; they are wired from birth to death. The hold count was being
used as a kind of reference count, specifically, the number of valid
page table entries within the page. Not surprisingly, these two
different uses imply different synchronization rules: in the machine-
independent layer access to the hold count requires the page queues
lock; whereas in the pmap layer the pmap lock is required. Thus,
continued use by the pmap layer of vm_page_unhold(), which asserts that
the page queues lock is held, made no sense.
2. _pmap_unwire_pte_hold() was too forgiving in its handling of the wired
count. An unexpected wired count on a page table page was ignored and
the underlying page leaked.
3. In a word, microoptimization. Using the wired count exclusively, rather
than a combination of the wired and hold counts, makes the code slightly
smaller and faster.
Reviewed by: tegge@
not sure yet about 5.x... MFC if needed.
Also fixes small problems with examining some registers and
some specific gdb transfer problems.
As the patch says:
This is not a pretty patch and only meant as a temporary
fix until a better solution is committed.
PR: i386/71715
Submitted by: Stephan Uphoff <ups@tree.com>
MFC after: 1 week
and which takes a M_WAITOK/M_NOWAIT flag argument.
Add compatibility isa_dmainit() macro which whines loudly if
isa_dma_init() fails.
Problem uncovered by: tegge
the loss of a page modified (PG_M) bit in a race between processors.
Quoting Tor:
One scenario where the old code could cause a lost PG_M bit is a
multithreaded linux program (or FreeBSD program using the
linuxthreads port) where one thread was starting a subprocess.
The thread doing fork() would call vmspace_fork(), which would then
call vm_map_copy_entry() which would call pmap_protect() on an area
possibly accessed by other threads.
Additionally, make the clearing of PG_M by pmap_protect() unconditional if
write permission is removed. Previously, PG_M could persist on a read-only
unmanaged page. That seems inconsistent and confusing.
In collaboration with: tegge@
MT5 candidate
PR: 61852
fully initialed when the pmap layer tries to call sched_pini() early in the
boot and results in an quick panic. Use ke_pinned instead as was originally
done with Tor's patch.
Approved by: julian
value was only enough for 8GB of RAM, the new value can do 16GB. This still
isn't optimal since it doesn't scale. Fixing this for amd64 looks to be
fairly easy, but for i386 will be quite difficult.
Reviewed by: peter
scheduler specific extension to it. Put it in the extension as
the implimentation details of how the pinning is done needn't be visible
outside the scheduler.
Submitted by: tegge (of course!) (with changes)
MFC after: 3 days
VT6122 gigabit ethernet chip and integrated 10/100/1000 copper PHY.
The vge driver has been added to GENERIC for i386, pc98 and amd64,
but not to sparc or ia64 since I don't have the ability to test
it there. The vge(4) driver supports VLANs, checksum offload and
jumbo frames.
Also added the lge(4) and nge(4) drivers to GENERIC for i386 and
pc98 since I was in the neighborhood. There's no reason to leave them
out anymore.
across frames. Basically, if the current frame is for the
'dblfault_handler' function, then get the next %eip and %ebp values to use
from the original TSS of the thread that has the saved state when the
double fault triggered.
MFC after: 4 days
and was propagated to nearly every platform. The boundary of the child needs
to consider the boundary of the parent and pick the minimum of the two, not
the maximum. However, if either is 0 then pick the appropriate one.
This bug was exposed by a recent change to ATA, which should now be fixed by
this change. The alignment and maxsegsz tag attributes likely also need
a similar review in the near future.
This is a MT5 candidate.
Reviewed by: marcel
Submitted by: sos (in part)
It can be switched back once 5.3 is tested and released. Also turn on
PREEMPTION as many of the stability problems with it have been fixed.
MT5: 3 days.
but with slightly cleaned up interfaces.
The KSE structure has become the same as the "per thread scheduler
private data" structure. In order to not make the diffs too great
one is #defined as the other at this time.
The KSE (or td_sched) structure is now allocated per thread and has no
allocation code of its own.
Concurrency for a KSEGRP is now kept track of via a simple pair of counters
rather than using KSE structures as tokens.
Since the KSE structure is different in each scheduler, kern_switch.c
is now included at the end of each scheduler. Nothing outside the
scheduler knows the contents of the KSE (aka td_sched) structure.
The fields in the ksegrp structure that are to do with the scheduler's
queueing mechanisms are now moved to the kg_sched structure.
(per ksegrp scheduler private data structure). In other words how the
scheduler queues and keeps track of threads is no-one's business except
the scheduler's. This should allow people to write experimental
schedulers with completely different internal structuring.
A scheduler call sched_set_concurrency(kg, N) has been added that
notifies teh scheduler that no more than N threads from that ksegrp
should be allowed to be on concurrently scheduled. This is also
used to enforce 'fainess' at this time so that a ksegrp with
10000 threads can not swamp a the run queue and force out a process
with 1 thread, since the current code will not set the concurrency above
NCPU, and both schedulers will not allow more than that many
onto the system run queue at a time. Each scheduler should eventualy develop
their own methods to do this now that they are effectively separated.
Rejig libthr's kernel interface to follow the same code paths as
linkse for scope system threads. This has slightly hurt libthr's performance
but I will work to recover as much of it as I can.
Thread exit code has been cleaned up greatly.
exit and exec code now transitions a process back to
'standard non-threaded mode' before taking the next step.
Reviewed by: scottl, peter
MFC after: 1 week
FULL_PREEMPTION is defined. Add a runtime warning to ULE if PREEMPTION is
enabled (code inspired by the PREEMPTION warning in kern_switch.c). This
is a possible MT5 candidate.
The removed argument could trivially be derived from the remaining one.
That in turn should be the same as curthread, but it is possible that curthread could be expensive to derive on some syste,s so leave it as an argument.
Having both proc and thread as an argumen tjust gives an opportunity for
them to get out sync.
MFC after: 3 days
in diagnostics. It has outlived its usefulness and has started
causing panics for people who turn on DIAGNOSTIC, in what is otherwise
good code.
MFC after: 2 days
remaining consumers to have the count passed as an option. This is
i4b, pc98/wdc, and coda.
Bump configvers.h from 500013 to 600000.
Remove heuristics that tried to parse "device ed5" as 5 units of the ed
device. This broke things like the snd_emu10k1 device, which required
quotes to make it parse right. The no-longer-needed quotes have been
removed from NOTES, GENERIC etc. eg, I've removed the quotes from:
device snd_maestro
device "snd_maestro3"
device snd_mss
I believe everything will still compile and work after this.
these two reasons:
1. On ia64 a function pointer does not hold the address of the first
instruction of a functions implementation. It holds the address
of a function descriptor. Hence the user(), btrap(), eintr() and
bintr() prototypes are wrong for getting the actual code address.
2. The logic forces interrupt, trap and exception entry points to
be layed-out contiguously. This can not be achieved on ia64 and is
generally just bad programming.
The MCOUNT_FROMPC_USER macro is used to set the frompc argument to
some kernel address which represents any frompc that falls outside
the kernel text range. The macro can expand to ~0U to bail out in
that case.
The MCOUNT_FROMPC_INTR macro is used to set the frompc argument to
some kernel address to represent a call to a trap or interrupt
handler. This to avoid that the trap or interrupt handler appear to
be called from everywhere in the call graph. The macro can expand
to ~0U to prevent adjusting frompc. Note that the argument is selfpc,
not frompc.
This commit defines the macros on all architectures equivalently to
the original code in sys/libkern/mcount.c. People can take it from
here...
Compile-tested on: alpha, amd64, i386, ia64 and sparc64
Boot-tested on: i386
valid pmap to the pmap functions that require one. Remove the checks for
NULL. (These checks have their origins in the Mach pmap.c that was
integrated into BSD. None of the new code written specifically for
FreeBSD included them.)
compile option. All FreeBSD packet filters now use the PFIL_HOOKS API and
thus it becomes a standard part of the network stack.
If no hooks are connected the entire packet filter hooks section and related
activities are jumped over. This removes any performance impact if no hooks
are active.
Both OpenBSD and DragonFlyBSD have integrated PFIL_HOOKS permanently as well.
The C code assumes that the carry bit is always kept from the previous
operation. However, the pointer indexing requires another add operation.
Thus, the carry bit from the first operation is tromped over by the
"addl" operation that ends up following it, so the "adcl" that follows
that has no effect because the carry bit is cleared before it.
The result is checksum failure on received packets.
The larger issue is that there isn't any other way of preventing the compiler
inserting arbitrary instructions between different __asm statements (and
that the commit message in revision 1.13 of in_cksum.h is wrong on
this point). From
http://developer.apple.com/documentation/DeveloperTools/gcc-3.3/gcc/Extended-Asm.html
---8<---8<---8<---
You can't expect a sequence of volatile asm instructions to remain
perfectly consecutive. If you want consecutive output, use a single
asm. Also, GCC will perform some optimizations across a volatile
asm instruction; GCC does not "forget everything" when it encounters
a volatile asm instruction the way some other compilers do.
---8<---8<---8<---
Also, this change also makes the ASM code much easier to read.
PR: 69257
Submitted by: Mike Bristow <mike@urgle.com>, Qing Li <qing.li@bluecoat.com>
directly. This removes a few more users of the stackgap and also marks
the syscalls using these wrappers MP safe where appropriate.
Tested on: i386 with linux acroread5
Compiled on: i386, alpha LINT
We were obtaining different spin mutexes (which disable interrupts after
aquisition) and spin waiting for delivery. For example, KSE processes
do LDT operations which use smp_rendezvous, while other parts of the
system are doing things like tlb shootdowns with a different mutex.
This patch uses the common smp_rendezvous mutex for all MD home-grown
IPIs that spinwait for delivery. Having the single mutex means that
the spinloop to aquire it will enable interrupts periodically, thus
avoiding the cross-ipi deadlock.
Obtained from: dwhite, alc
Reviewed by: jhb
with VmWare 4.x. At least with VmWare version 4.5.2, i386 version of
atomic_cmpset_int() is about 30 times slower than non-i386 version. It
makes this delta a good 5.3 MFC candidate, since otherwise it will
mislead users who run FreeBSD under modern VmWare otherwise.
Since pmap_enter() calls pmap_invalidate_page(), which needs interrupts
enabled in the SMP case, we defer the disable to right before saving the
register context. This has been incorrect for about a year but caused no
real problems because the identity page never actually replaces a previously
mapped page and suspend/resume on SMP systems has been uncommon.
Tested by: sos
MFC after: 3 days
parent rather than track resources locally. The original code
was incomplete in that it would only honor requests for resources
that already exist in its resource list. This prevented many ISA
identify routines from allocating temporary resources. Passing
the requests up to legacy's parent losing no functionality and
allows these requests to succeed.
Reviewed by: imp, jhb
Approved by: RE
logical CPUs on a system to be used as a dedicated watchdog to cause a
drop to the debugger and/or generate an NMI to the boot processor if
the kernel ceases to respond. A sysctl enables the watchdog running
out of the processor's idle thread; a callout is launched to reset a
timer in the watchdog. If the callout fails to reset the timer for ten
seconds, the watchdog will fire. The sysctl allows you to select which
CPU will run the watchdog.
A sample "debug.leak_schedlock" is included, which causes a sysctl to
spin holding sched_lock in order to trigger the watchdog. On my Xeons,
the watchdog is able to detect this failure mode and break into the
debugger, which cannot otherwise be done without an NMI button.
This option does not currently work with sched_ule due to ule's push
notion of scheduling, similar to machdep.hlt_logical_cpus failing to
work with that scheduler.
On face value, this might seem somewhat inefficient, but there are a
lot of dual-processor Xeons with HTT around, so using one as a watchdog
for testing is not as inefficient as one might fear.
* Serialize access to the sysctl routines and the notify handler
* Assert that the sx lock is held in any functions they call.
* Note that recursively calling to re-enable the hotkeys is sub-optimal.
to allow dumping per-thread machine specific notes. On ia64 we use this
function to flush the dirty registers onto the backingstore before we
write out the PRSTATUS notes.
Tested on: alpha, amd64, i386, ia64 & sparc64
Not tested on: arm, powerpc
a standard configuration similar to [NO_]ADAPTIVE_MUTEXES. This
feature causes Giant to be included in the set of mutexes adaptively
spun on. It appears to have a positive effect on performance on SMP
across several workloads, including measurements of a 16% improvement
on buildworld, and 30%+ improvement for MySQL using the supersmack
benchmark with Giant over the network stack; a 6% improvement without
Giant on the network stack (as a result of less giant contention).
fix the obvious bugs, nastier ones reside below the surfac), and having
it commented out here just encourages people to try it.
# I'm not removing it from the base system, yet.
calls. Note that the information included is a bit different from the
existing KTR traces generated on powerpc, as I'm primarily interested
in kernel context (thread, syscall #, proc, etc), not the user
arguments to the system call. Some convergence would be useful here.
location (for the wake code). It should not be needed since we don't
map other pages at the same location and if there was an old mapping, it
would be restored by a fault. The old code had serious problems, namely
that it was restoring the new page it had just removed (not opage) and
it could only guess at the right protection (since there's no
pmap_extract_protect function). Thanks to Alan Cox for explaining much
of this to me.
Also, remove a commented-out initializecpu() call since it is not needed.
Restoring the cpu context is better than attempting to init from scratch.
Reviewed by: alc (earlier version)
spin-wait code to use the same spin mutex (smp_tlb_mtx) as the TLB ipi
and spin-wait code snippets so that you can't get into the situation of
one CPU doing a TLB shootdown to another CPU that is doing a lazy pmap
shootdown each of which are waiting on each other. With this change, only
one of the CPUs would do an IPI and spin-wait at a time.
vm_page_sleep_if_busy() and the page table page's busy flag as a
synchronization mechanism on page table pages.
Also, relocate the inline pmap_unwire_pte_hold() so that it can be used
to shorten _pmap_unwire_pte_hold() on alpha and amd64. This places
pmap_unwire_pte_hold() next to a comment that more accurately describes
it than _pmap_unwire_pte_hold().
