The 32-bit bootloaders now link against libstand.a in sys/boot/libstand32,
so there is no need to force /usr/lib/libstand.a to be 32-bit.
This is equivalent to r261568 for amd64.
Sponsored by: The FreeBSD Foundation
If rare conditions such as concurrent conflicting manipulation of the
filesystem occur, fts_read() frees the current FTSENT without adjusting
the pointers in the FTS accordingly. A later fts_close() then frees the
same FTSENT again.
Reported by: pho
Tested by: pho
MFC after: 1 week
The 32-bit bootloaders now link against libstand.a in sys/boot/libstand32,
so there is no need to force /usr/lib/libstand.a to be 32-bit.
Sponsored by: The FreeBSD Foundation
device drivers. Recent versions of u-boot run with the MMU enabled, and
require DMA-based I/O to be aligned to cache line boundaries.
These changes are based on a patch originally submitted by Juergen Weiss,
but I reworked them and thus any problems are purely my fault.
Submitted by: "Juergen Weiss" <weiss@uni-mainz.de>
Reviewed by: imp, nwhitehorn, jhb
- Similar to the hack for bootinfo32.c in userboot, define
_MACHINE_ELF_WANT_32BIT in the load_elf32 file handlers in userboot.
This allows userboot to load 32-bit kernels and modules.
- Copy the SMAP generation code out of bootinfo64.c and into its own
file so it can be shared with bootinfo32.c to pass an SMAP to the i386
kernel.
- Use uint32_t instead of u_long when aligning module metadata in
bootinfo32.c in userboot, as otherwise the metadata used 64-bit
alignment which corrupted the layout.
- Populate the basemem and extmem members of the bootinfo struct passed
to 32-bit kernels.
- Fix the 32-bit stack in userboot to start at the top of the stack
instead of the bottom so that there is room to grow before the
kernel switches to its own stack.
- Push a fake return address onto the 32-bit stack in addition to the
arguments normally passed to exec() in the loader. This return
address is needed to convince recover_bootinfo() in the 32-bit
locore code that it is being invoked from a "new" boot block.
- Add a routine to libvmmapi to setup a 32-bit flat mode register state
including a GDT and TSS that is able to start the i386 kernel and
update bhyveload to use it when booting an i386 kernel.
- Use the guest register state to determine the CPU's current instruction
mode (32-bit vs 64-bit) and paging mode (flat, 32-bit, PAE, or long
mode) in the instruction emulation code. Update the gla2gpa() routine
used when fetching instructions to handle flat mode, 32-bit paging, and
PAE paging in addition to long mode paging. Don't look for a REX
prefix when the CPU is in 32-bit mode, and use the detected mode to
enable the existing 32-bit mode code when decoding the mod r/m byte.
Reviewed by: grehan, neel
MFC after: 1 month
* The RFC says (in section 10.1) that only when extbuf is not NULL,
extlen shall be checked, so don't perform this check when NULL is
passed.
* socklen_t is unsigned, so checking extlen for less than zero is
not needed.
Submitted by: swildner@dragonflybsd.org
Reviewed by: Mark Martinec <Mark.Martinec+freebsd@ijs.si>
Reviewed by: hrs
Obtained by: DragonFlyBSD
the signal second time, by adding the missed else before if statement.
While there, postpone initializing local curthread variable until
passed signal number is checked for validity.
Submitted by: John Wolfe <jlw@xinuos.com>
PR: threads/186309
MFC after: 1 week
This also fixes asserts on removal of the module for the mpc74xx.
The PowerPC 970 processors have two different types of events: direct events
and indirect events. Thus far only direct events are supported. I included
some documentation in the driver on how indirect events work, but support is
for the future.
MFC after: 1 month
commit c1acf022c533c5ae27e0cd556977eafe3f5959eb
Author: Brooks Davis <brooks@one-eyed-alien.net>
Date: Fri Jan 17 21:46:44 2014 +0000
Add an option WITHOUT_NCURSESW to suppress building and linking to
libncursesw. While wide character support it useful we'd like to
only need one ncurses library on embedded systems.
MFC after: 4 weeks
Sponsored by: DARPA, AFRL
the virtio backends.
- Add a new ioctl to export the count of pins on the I/O APIC from vmm
to the hypervisor.
- Use pins on the I/O APIC >= 16 for PCI interrupts leaving 0-15 for
ISA interrupts.
- Populate the MP Table with I/O interrupt entries for any PCI INTx
interrupts.
- Create a _PRT table under the PCI root bridge in ACPI to route any
PCI INTx interrupts appropriately.
- Track which INTx interrupts are in use per-slot so that functions
that share a slot attempt to distribute their INTx interrupts across
the four available pins.
- Implicitly mask INTx interrupts if either MSI or MSI-X is enabled
and when the INTx DIS bit is set in a function's PCI command register.
Either assert or deassert the associated I/O APIC pin when the
state of one of those conditions changes.
- Add INTx support to the virtio backends.
- Always advertise the MSI capability in the virtio backends.
Submitted by: neel (7)
Reviewed by: neel
MFC after: 2 weeks
known in advance, or where the caller doesn't care and just keeps
reading until it hits EOF.
In fetch_read(): the socket is non-blocking, so read() will return 0
on EOF, and -1 (errno == EAGAIN) when the connection is still open but
there is no data waiting. In the first case, we should immediately
return 0. The EINTR case was also broken, although not in a way that
matters.
In fetch_writev(): use timersub() and timercmp() as in fetch_read().
In http_fillbuf(): set errno to a sensible value when an invalid chunk
header is encountered.
In http_readfn(): as in fetch_read(), a zero return from down the
stack indicates EOF, not an error. Furthermore, when io->error is
EINTR, clear it (but no errno) before returning so the caller can
retry after dealing with the interrupt.
MFC after: 3 days
simply not trying to return exactly what the caller asked for - just
return whatever we got and let the caller be the judge of whether it
was enough. If an error occurs or the connection times out after we
already received some data, return a short read, under the assumption
that the next call will fail or time out before we read anything.
As it turns out, none of the code that calls fetch_read() assumes an
all-or-nothing result anyway, except for a couple of lines where we
read the CR LF at the end of a hunk in HTTP hunked encoding, so the
changes outside of fetch_read() and http_readfn() are minimal.
While there, replace select(2) with poll(2).
MFC after: 3 days
properly include sys/ headers from the source tree instead of the
host.
These patches are also applied to libdwarf since libdwarf requires
the same sys/ headers as libelf.
device is an active kernel console and "off" otherwise. This is designed to
allow serial-booting x86 systems to provide a login prompt on the serial line
by default without providing one on all systems by default.
Comments and suggestions by: grehan, dteske, jilles
MFC after: 1 month
The resolver in libc creates a kqueue for watching a single file descriptor.
This can be done using poll() which should be lighter on the kernel and
reduce possible problems with rlimits (file descriptors, kqueues).
Reviewed by: jhb
one significant difference: for LIB32 builds both TARGET_ARCH
and MACHINE_ARCH are defined. TARGET_ARCH confusingly holds the
architecture of the host (e.g. amd64), while MACHINE_ARCH holds
the architecture were trying to build (e.g. i386). With both
set and different, r260022 changed the behaviour to interpret
the condition as building a cross-amd64 libkvm on i386, when
obviously we're trying to build an i386 version on amd64. When
COMPAT_32BIT is defined, we're building LIB32 and ignore the
value of TARGET_ARCH as we did before.
These files are required to get packages in ports to build against atf and
also to get a couple of currently-failing tests to pass.
I'm following the approach already used by the libusb pkg-config files
installed by the system regarding the location and the install rules.
MFC after: 5 days
