#!bin/sh
# Original version of this by Michael Reifenberger
# <root@nihil.plaut.de>.
mdconfig -d -u 11 >/dev/null 2>&1
dd if=/dev/zero of=zz bs=1m count=1
while :
do
mdconfig -a -t vnode -f zz -u 11
fdisk -f - -iv /dev/md11 <<EOF1
g c1 h64 s32
p 1 165 0 2048
a 1
EOF1
mdconfig -d -u 11
done
Garbage pointers in __si_u were not cleared by destroy_dev(). Not
clearing si_disk made the above fatal because the disk layer uses
si_disk as a flag to indicate that the dev_t has been completely
initialized. disk_destroy() clears si_disk for the parent dev_t
but doesn't get called for children.
Not fixed:
- setting the undocumented sysctl debug.free_devt should cause more
complete destruction of the dev_t including clearing of __si_u, but
actually causes the above to panic a little earlier.
- the loop leaks 10 memory allocations per iteration (4 DEVFS, 2 devbuf
and 4 dev_t).
Reviewed by: timeout by MAINTAINER after 3 months
the symbol index defined by the relocation. The elf_lookup() support
function is to be used by elf_reloc() when symbol lookups need to be
done. The elf_lookup() function operates on the symbol index and
will do a symbol name based lookup when such is required, otherwise
it uses the symbol index directly. This solves the problem seen on
ia64 where the symbol hash table does not contain local symbols and
a symbol name based lookup would fail for those symbols.
Don't pass the symbol name to elf_reloc(), as it isn't used any more.
Exit with nonzero status if a conversion failed.
Play nice if used as a shell builtin (currently disabled).
Submitted by: bde (partially)
Approved by: mike
calls associated with the pool and the objects allocated out from the
pool.
- Insert atm_attributes_zone which is a uma_zone that is used just as the
atm_attributes_pool was (including the max objects value). Also, used
the appropriate zalloc and zfree's where necesary.
ahc_eisa.c:
ahc_pci.c:
Conform to new aic7xxx IRQ API.
Adapt to aic7xxx_freebsd -> aic7xxx_osm changes.
aic7770.c:
Disable card generated interrupt early in our probe for
"extra safety"
Commonize some seeprom code with the PCI side of the driver.
aic7xxx.c:
Correctly initialize a few scratch ram locations during
a sequencer restart. This avoids spurious sequencer ram
parity errors in some configurations.
Include the softc in ahc_update_residual calls. We need it
for some diagnostics in this code path.
Flag a data overrun on an auto-request sense failure as a
CAM_AUTOSENSE_FAIL rather than a CAM_DATA_RUN_ERR.
Force a renegotiation after noticing a parity error. This
covers targets that lose our negotiation settings but don't
bother to give us a unit attention condition. This can happen
if a target fails during a reselection of us during a cable
pull.
Convert some code to using constants.
Fix some typos.
Correct target mode message loop handling. ahc_clear_msg_state
was not clearing the "need to go to message out phase" bit once
our loop was over.
Simplify some abort handling code.
Include tag information in target mode immediate notify events.
When shutting down EISA controllers, don't EISA BIOS settings in
the high portions of scratch ram. This fixes warm boot issues on
some systems.
Save a bit of space by only allocating the SCBs that we can use.
Avoid some code paths in ahc_abort_scbs() if we are currently
acting as a target.
Correctly cleanup stranded SCBs in the card's SCB array. These
are SCBs who's mapping has already been torn down by code that
aborted the SCB by seeing it in another list first.
Add a comment about some potential bus reset issues for target
mode on Twin (EISA only) controllers.
aic7xxx.h:
Cleanup the hardware scb definitions a bit.
Allocate a ful 256 byte scb mapping index. This simplifies
the lookup code since the table covers all possible (and potentially
bogus) values.
Make AHC_DEBUG work again.
aic7xxx.reg:
Updates to hardware SCB definition.
New definitions for target mode fixes.
aic7xxx.seq:
In target mode, initialize SAVED_LUN just after we receive
the identify message. It may be required in the error recovery
path when a normal cdb packet (includes lun) is not sent up to
the host for processing.
Respond to irregular messages during a selection in target mode.
Defer looking for space for a cdb packet until we are about to
enter command phase. We want to be able to handle irregular messages
even if we would otherwise return QUEUE_FULL or BUSY.
Add support for sending Ignore Wide Residue messages as a target.
In the disable disconnect case in target mode, set our transfer
rate correctly once data are availble.
aic7xxx_93cx6.c:
aic7xxx_93cx6.h:
Add the ability to write and erase the seeprom.
aic7xxx_inline.h:
Correct Big Endian handling of large cdb sizes (> 12 bytes).
Adaptec to changes in the calc_residual API.
Correct a target mode bug where we always attempted to service
the input queue even if no progress could be made due to lack
of ATIOs.
aic7xxx_osm.c:
Adaptec to new IRQ mapping API. The new API allows the core
to only enable our IRQ mapping once it is safe (sufficient
initialization) to do so.
Slap bootverbose protection around some diagnostics.
Only attempt DT phases if we are wide.
aic7xxx_osm.h:
Enable big endian support.
Adjust for IRQ API change.
aic7xxx_pci.c:
Be more careful about relying on subvendor 9005 information.
We now only trust it for HBAs. This should allow the driver
to attach to some MBs where the subvendor/device information
does not follow the Adaptec spec.
Only enable interrupts on the card once we are fully setup.
Disable external SCB ram usage on the aic7895. I have not
been able to make it 100% reliable.
Adjust to seeprom routines being properly prefixed with "ahc".
Fix a few bugs in the external SCB ram probing routine. We
need to clear any parity errors we've triggered during the
probe to avoid future, fatal, interrupts.
If we detect an invalid cable combination, pretent there are
no cable at all. This will enable all of the terminators
which is probably the safest configuration we can "guess".
MFC after: 4 days
2, but that's not the case. This fixes the case where there were slots
in the PIR table that had no bits set, but we assumed they did and used
strange results as a result.
o Map invalid INTLINE registers to 255 in pci_cfgreg.c. This should allow
us to remove the bogus checks in MI code for non-255 values.
I put these changes out for review a while ago, but no one responded
to them, so into current they go.
This should help us work better on machines that don't route
interrupts in the traditional way.
MFC After: 4286 millifortnights
