tasks. Since the host controllers rely on tasks to process transfer
timeouts, if a synchronous transfer from a driver was invoked from
a task and timed out, it would never complete because the single
task thread was stuck performing the synchronous transfer so couldn't
process the timeout.
This affected the axe, udav and ural drivers.
Problem hardware provided by: guido
o day and mday are the same. No need to subtract 1 from mday.
o Set dow to -1 as clock_ct_to_ts() checks this field and
returns EINVAL on any day of the week but Sunday.
Unlock the vnode in devfs_close() while calling into the driver d_close()
routine.
devfs_revoke() changes by: ups
Reviewed and bugfixes by: tegge
Tested by: mbr, Peter Holm
Approved by: pjd (mentor)
MFC after: 1 week
- Count (scheduling of) software interrupts (SWIs) as SWIs, not as
hardware interrupts.
- Don't count (scheduling of) delayed SWIs as interrupts at all, since
in the delayed case it is expected that there are many more scheduling
calls than handling calls. Perhaps all interrupts should be counted
only when they are handled, but it is only counts of delayed SWIs that
shouldn never be combined with the other counts.
subr_trap.c:
- Count (handling of) Asynchronous System Traps (ASTs) as traps, not as
software interrupts.
Before these changes, the counter for SWIs only counted ASTs, and SWIs
weren't counted separately, but a subcounter for ASTs alone is less
needed than for most other exception sources.
4.4BSD-Lite uses the counters for similar things (actually matching
their names) on its main arches (hp300, ..., !i386) where more of the
exceptions are in hardware.
snd_emu10k1 and snd_emu10kx into one line. The 'pci' dependency here
adds no value, so I eliminted it (we don't have a snd.all file that
might make it mildly useful, and even then it wouldn't be that
useful). With the pci optional component eliminated, I could use the
'|' operator. I could have also include pci on both sides of the |
operator, but since it isn't a value add at all, it was better to
eliminate it.
- Inline ship_msg() into ngs_rcvmsg().
- Plug memory leak in case if no control socket present.
- Remove malloc() and allocate the sockaddr on stack.
- style(9).
long being DMA'ed 2 (or 1) bytes past the end of the mbuf and corrupting
random kernel memory. I had forgotten about the 2 bytes of implict
padding the firmware assumes.
Sponsored by: Myricom Inc.
- Use malloc() and free() instead of MALLOC() and FREE() macros.
- Do not check malloc results if M_WAITOK was used.
- Remove linked list of all netgraph sockets. It isn't needed.
- Use ng_findhook() instead of searching the list ourselves.
- Use NG_WAITOK in syscalls.
- Remove unneeded includes.
- style(9)
directory before the ${MACHINE_ARCH}/${MACHINE_ARCH} directory so that
machine-specific files take precedence of architecture-specific ones.
This fixes the build on sun4v which doesn't use the sparc64 version
of mem.c.
Tested by: make universe
- Fix the locking protocol to eliminate races between normal I/O and AENs.
- Various small improvements and usability tweaks.
Sponsored by: IronPort
Portions Submitted by: Doug Ambrisko
- Use bus_dmamap_load_mbuf_sg() to eliminate the need for the callback and
all of the extra bookkeeping associated with it.
- Eliminate the bce_dmamap_arg structure and streamline the memory allocation
routines to not need it. This does change some of the debugging messages.
- Refactor the loop that fills the buffer descriptor so that it can be done
with a single set of logic in a single loop instead of two sets of logic.
- Eliminate the need to cache and pass descriptor indexes between the start
loop and the encap function.
- Change the start loop to always check the ifnet sendq for more work.
This significantly helps the driver withstand large UDP workloads, though
it's still not perfect. I suspect the remaining work lies with handling
the OACTIVE flag, and also in possibly streamlining the interrupt handler
some. It is, however, nearly on par with the other popular gigabit drivers
in terms of stability now.
Implement the linux_io_* syscalls (AIO). They are only enabled if the native
AIO code is available (either compiled in to the kernel or as a module) at
the time the functions are used. If the AIO stuff is not available there
will be a ENOSYS.
From the submitter:
---snip---
DESIGN NOTES:
1. Linux permits a process to own multiple AIO queues (distinguished by
"context"), but FreeBSD creates only one single AIO queue per process.
My code maintains a request queue (STAILQ of queue(3)) per "context",
and throws all AIO requests of all contexts owned by a process into
the single FreeBSD per-process AIO queue.
When the process calls io_destroy(2), io_getevents(2), io_submit(2) and
io_cancel(2), my code can pick out requests owned by the specified context
from the single FreeBSD per-process AIO queue according to the per-context
request queues maintained by my code.
2. The request queue maintained by my code stores contrast information between
Linux IO control blocks (struct linux_iocb) and FreeBSD IO control blocks
(struct aiocb). FreeBSD IO control block actually exists in userland memory
space, required by FreeBSD native aio_XXXXXX(2).
3. It is quite troubling that the function io_getevents() of libaio-0.3.105
needs to use Linux-specific "struct aio_ring", which is a partial mirror
of context in user space. I would rather take the address of context in
kernel as the context ID, but the io_getevents() of libaio forces me to
take the address of the "ring" in user space as the context ID.
To my surprise, one comment line in the file "io_getevents.c" of
libaio-0.3.105 reads:
Ben will hate me for this
REFERENCE:
1. Linux kernel source code: http://www.kernel.org/pub/linux/kernel/v2.6/
(include/linux/aio_abi.h, fs/aio.c)
2. Linux manual pages: http://www.kernel.org/pub/linux/docs/manpages/
(io_setup(2), io_destroy(2), io_getevents(2), io_submit(2), io_cancel(2))
3. Linux Scalability Effort: http://lse.sourceforge.net/io/aio.html
The design notes: http://lse.sourceforge.net/io/aionotes.txt
4. The package libaio, both source and binary:
http://rpmfind.net/linux/rpm2html/search.php?query=libaio
Simple transparent interface to Linux AIO system calls.
5. Libaio-oracle: http://oss.oracle.com/projects/libaio-oracle/
POSIX AIO implementation based on Linux AIO system calls (depending on
libaio).
---snip---
Submitted by: Li, Xiao <intron@intron.ac>
it introduced a check after the call to file system's get pages method
that assumes that the get pages method does not change the array of pages
that is passed to it. In the case of vnode_pager_generic_getpages(),
this assumption has been incorrect. The contents of the array of pages
may be shifted by vnode_pager_generic_getpages(). Likely, the problem
has been hidden by vnode_pager_haspage() limiting the set of pages that
are passed to vnode_pager_generic_getpages() such that a shift never
occurs.
The fix implemented herein is to adjust the pointer to the array of pages
rather than shifting the pages within the array.
MFC after: 3 weeks
Fix suggested by: tegge
an error returned by VOP_BMAP() and a hole in the file.
Change the callers to vnode_pager_addr() such that they return
VM_PAGER_ERROR when VOP_BMAP fails instead of a zero-filled page.
Reviewed by: tegge
MFC after: 3 weeks
if backward copatibility options are present) from attempting
to free memory that wasn't allocated. This is an old bug, and
previously it would attempt to free a null pointer. I noticed
this bug when working on the previous revision, but forgot to
fix it.
Security: local DoS
Reported by: Peter Holm
MFC after: 3 days
VA_MARK_ATIME feature to fix POSIX conformance fore execve() and mmap(),
we thought that it was optimized well enough for the one file system
that supports it (ffs) and harmless for other file systems (except
layered ones which already get the layering for VOP_SETATTR() wrong).
However, nfs_setattr() doesn't do much parameter checking, so when
it gets a combination of parameters that it doesn't understand, it
always does a Setattr RPC. This RPC can't do anything good, and for
VA_MARK_ATIME it is null except for wasting a lot of time.
This is the smallest and easiest to fix of several bugs that have
increased the number of RPCs for kernel builds on nfs by more than
100% since 2004-11-05. The real-time increase depends on network
latency and parallelization and can also be very large (approaching
the same percentage for unparallelized operations like "make depend"
on systems with fast CPUs and high-latency networks).
method is defined, to avoid memory being modified after free.
Temporarily increase refcount in destroy_devl() to avoid a double free
if dev_rel() is called while waiting for thread count to reach zero.
size aligned requiring heavy usage of vm_page_alloc_contig
This change makes vm_page_alloc_contig SMP safe
Approved by: scottl (acting as backup for mentor rwatson)
removals, including failures, into the callwheel.
XXX: Most of the CTR() macros are called with callout_lock spin mutex
held, thus won't be logged into file, if KTR_ALQ is used. Moving the
CTR() macros out from the spinlocked code would require copying of all
arguments. I'm too lazy to do this.
entries' by src:port and dst:port pairs. IPv6 part is non-functional
as ``limit'' does not support IPv6 flows.
PR: kern/103967
Submitted by: based on Bruce Campbell patch
MFC after: 1 month
(PICs) rather than interrupt sources. This allows interrupt controllers
with no interrupt pics (such as the 8259As when APIC is in use) to
participate in suspend/resume.
- Always register the 8259A PICs even if we don't use any of their pins.
- Explicitly reset the 8259As on resume on amd64 if 'device atpic' isn't
included.
- Add a "dummy" PIC for the local APIC on the BSP to reset the local APIC
on resume. This gets suspend/resume working with APIC on UP systems.
SMP still needs more work to bring the APs back to life.
The MFC after is tentative.
Tested by: anholt (i386)
Submitted by: Andrea Bittau <a.bittau at cs.ucl.ac.uk> (3)
MFC after: 1 week
vnode_pager_generic_getpages(): (1) that VOP_BMAP() is unsupported by the
underlying file system and (2) an error in performing the VOP_BMAP().
Previously, vnode_pager_generic_getpages() assumed that all errors were
of the first type. If, in fact, the error was of the second type, the
likely outcome was for the process to become permanently blocked on a busy
page.
MFC after: 3 weeks
Reviewed by: tegge
not trust jails enough to execute audit related system calls. An example of
this is with su(1), or login(1) within prisons. So, if the syscall request
comes from a jail return ENOSYS. This will cause these utilities to operate
as if audit is not present in the kernel.
Looking forward, this problem will be remedied by allowing non privileged
users to maintain and their own audit streams, but the details on exactly how
this will be implemented needs to be worked out.
This change should fix situations when options AUDIT has been compiled into
the kernel, and utilities like su(1), or login(1) fail due to audit system
call failures within jails.
This is a RELENG_6 candidate.
Reported by: Christian Brueffer
Discussed with: rwatson
MFC after: 3 days
is suspending/suspended. Doing so may result in deadlock. Instead, set the
(new) IN_LAZYACCESS flag, that becomes IN_MODIFIED when suspend is lifted.
Change the locking protocol in order to set the IN_ACCESS and timestamps
without upgrading shared vnode lock to exclusive (see comments in the
inode.h). Before that, inode was modified while holding only shared
lock.
Tested by: Peter Holm
Reviewed by: tegge, bde
Approved by: pjd (mentor)
MFC after: 3 weeks
since they just duplicated the MI `reset' command. Instead of removing
them, make `reboot' an MI alias for `reboot' since this gives a better
way of killing the `r' alias for `reset'. Remove the `registers' command
that was used to kill the alias.
Turn the powerpc and sparc64 MD `halt' command into an MI command.
A copy of sparc64/db_interface.c grew in sun4v just after I found the
extra reboot commands. It has not been changed, and is now not
identical. Duplicated commands come out duplicated in ddb's online
help, but cause large problems when used (e.g., on i386's with 2 halt's
and an hwatch, typing h doesn' give the expected message about an
ambiguous command, but hangs like the halt command or a looping parseri
would).
suppression is only needed at ends of lines, but rev.1.32 forced it
off precisely there.
The --More-- prompt is now cleared by explicitly forcing out the
whitespace in "\r \r". It might be better to use the line
editor's clearing functions, but these are currently static and not
much different.
- `b' is now an official alias for `break'. It used to be an unofficial
alias, but this was broken by adding the `bt' alias for `trace'.
- `t' is now an official alias for `trace'. It used to be an unofficial
alias, but this was broken by adding the `thread' command.
- `registers' is now an alias for `show registers'. This is a hack to
break the unofficial `r' alias for `reset'. `r' really means
`registers' in some debuggers, so I sometimes type it accidentally and
am annoyed when it resets the system. A short command shouldn't have
such a large effect. Now at least `res' must be typed to disambiguate
`reset'.
output width of 79, only 6 columns of width 12 each fit, but 7 columns
were printed.
The fix is to pass the width of the next output to db_end_line() and
not assume there that this width is always 1.
Related unfixed bugs:
- 1 character is wasted for a space after the last column
- suppression of trailing spaces used to limit the misformatting, but
seems to have been lost
- in db_examine(), the width of the next output is not know and is
still assumed to be 1.
- Add entries in the uscanner.4 man page (along with missing 3500).
PR: usb/100957 [1], usb/100992 [2]
Submitted by: Jim Teresco <terescoj@teresco.org> [1],
Walter C. Pelissero <walter.pelissero@iesy.net> [2]
MFC after: 3 days
in ip6_output. In case this fails handle the error directly and log it[1].
In addition permit CARP over v6 in ip_fw2.
PR: kern/98622
Similar patch by: suz
Discussed with: glebius [1]
Tested by: Paul.Dekkers surfnet.nl, Philippe.Pegon crc.u-strasbg.fr
MFC after: 3 days
will fix a problem where you boot w/ the default of autoselect, but then
set the speed to 100/full, the switch will keep the autoselect/100/full
negotiation... This will continue to work till someone resets the switch
or unplugs the cable resulting in the switch failing to autoneg and falling
back to 100/half, causing a hard to track down duplex mismatch..
Submitted by: nCircle Network Security, Inc.
MFC after: 1 week
- Add support for the Conexant Waikiki/CX20551-22, found
in most Toshiba P100 series laptops. Despite of growing
urban legend of "unsupported Conexant", this codec is fully
supported in this driver.
Note: Toshiba P100 has broken (acpi) BIOS, thus rendering
its soundchip useless. Please disable ACPI, or get
BIOS updates (if any).
Found/tested by: Vulpes Velox <v.velox@vvelox.net>
URL: http://lists.freebsd.org/pipermail/freebsd-multimedia/2006-September/004896.html
- Parser cleanups to handle possible oss/mixer collision. Found
after parsing Conexant Waikiki nodes.
- Increase resilient against resource failure during attach/detach.
- Implement simple config through hint.pcm.<unit>.config. Supported
options:
gpio0 (default on Acer), gpio1, gpio2, softpcmvol,
fixedrate (default), forcestereo (default)
* Option prefixed with "no" (such as "nofixedrate") will do
the opposite.
* Options can be separated using space " " or comma ",".
* The "no" option will take precedence over anything else.
Example:
hint.pcm.0.config="gpio2,nofixedrate,noforcestereo,nogpio0,softpcmvol"
hint.pcm.0.config="softpcmvol noforcestereo"
