The appropriate subdirectories are handled by lib/csu/Makefile. There's
no need to duplicate this logic in Makefile.inc1 and lib/Makefile.
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D2523
frames to 0
From IEEE Std. 802.11-2012, 8.3.2.1 "Data frame format", p. 415 (513):
"The Sequence Control field for QoS (+)Null frames is ignored by the receiver
upon reception."
At this moment, any <mode>_input() function interprets them as regular QoS data
frames with TID = 0. As a result, stations, that use another TX sequence for
QoS Null frames (e.g. wpi(4), where (QoS) Null frames are generated by the
firmware), may experience significant packet loss with any other NIC in hostap
mode.
Tested:
* wpi(4) (author)
* iwn(4) - Intel 5100, STA mode (me)
PR: kern/200128
Submitted by: Andriy Voskoboinyk <s3erios@gmail.com>
to handle the ARM conditional execution.
While here fix a bug found by this in the hard-float code, cc is the
opposite of cs. The former is used for 'less than' in floating-point code
and is executed when the C (carry) bit is clear, the latter is used when
greater than, equal, or unordered, and is executed when the C bit is set.
The aml8726-m3 SoC is identified as a Cortex A9-r2 rev 4 CPU and
it hangs sometimes during the boot when WFI is used by the kernel.
Differential Revision: https://reviews.freebsd.org/D2473
Submitted by: John Wehle
Suggested by: ian@
packets on tunnel interfaces. Add support of these ioctls to gre(4),
gif(4) and me(4) interfaces. For incoming packets M_SETFIB() should use
if_fib value from ifnet structure, use proper value in gre(4) and me(4).
Differential Revision: https://reviews.freebsd.org/D2462
No objection from: #network
MFC after: 2 weeks
Sponsored by: Yandex LLC
because a link where looped back NS messages are permanently observed
does not work with either NDP or ARP for IPv4.
- draft-ietf-6man-enhanced-dad is now RFC 7527.
Discussed with: hiren
MFC after: 3 days
The default behavior is to infer the logical and physical sector sizes from
the block device backend. However older versions of Windows only work with
specific logical/physical combinations:
- Vista and Windows 7: 512/512
- Windows 7 SP1: 512/512 or 512/4096
For this reason allow the sector size to be specified using the following
block device option: sectorsize=logical[/physical]
Reported by: Leon Dang (ldang@nahannisys.com)
Reviewed by: grehan
MFC after: 2 weeks
For RE purposes, we use the default (/R within the chroot), so
this helps avoid copying files multiple times and xz(1)-compressing
additional times when not needed.
Again, this Makefile is not for general consumption.
Sponsored by: The FreeBSD Foundation
a 474-line kludge of a shell script to pre-create the directory
hierarchy on ftp-master.
This is not in any way connected to the build, and there is no
intention to do so. This only intent here is to try to make
things a little bit easier for me. But I've probably just made
things worse.
Sponsored by: The FreeBSD Foundation
not one that needs to be negotiated. Use the host capabilities
field and not the negotiated field when verifying that indirect
descriptors are supported.
Found with the Redhat Windows viostor driver, which clears
the indirect capability in the negotiated caps and then starts
using them.
Reported and tested by: Leon Dang (ldang@nahannisys.com)
MFC after: 2 weeks
Summary:
The Freescale PCIe Root Complex shows up as a Processor class device, PowerPC
subclass, so the generic PCI code ignores it for a bridge. This adds support
for it.
As part of this, update the Freescale PCI hostbridge driver, to allow probing
beyond the root complex, instead of only allowing "proper" PCI-PCI bridges.
Reviewers: #powerpc, marcel, nwhitehorn
Reviewed By: nwhitehorn
Subscribers: imp
Differential Revision: https://reviews.freebsd.org/D2442
Relnotes: yes
because the i386 pmap on which the new armv6 pmap is based had it, and in
r281707 pmap_lazyfix() was removed from the i386 pmap.
Discussed with: kib
Submitted by: Michal Meloun (via Svatopluk Kraus)
main ARMv6 target, the Raspberry Pi, doesn't support Thumb-2.
This as been tested with a Thumb-2 userland, however building one is
currently unsupported as there are known toolchain issues breaking some
binaries. Further work will also be needed to decide on the method of
selecting which instruction set to build for, and to benchmark both to
find how building everything as Thumb-2 will affect performance.
Relnotes: yes
Introduce further adjustments to the renaming of libmd
symbols: make sure that we do not generate dangling weak
aliases, as this causes build failures on MIPS.
Tested by: sbruno
This allows to ensure that we do not write to a file that was opened
for reading only or vice versa.
Also, use the correct capability in in zfs_ioc_send_new().
Differential Revision: https://reviews.freebsd.org/D2382
Reviewed by: delphij
MFC after: 17 days
Sponsored by: ClusterHQ
positive value since it adds the current tick to its result. This differs
from the behaviour in Linux, whose implementation does not add the extra
tick, so subtract the extra tick in the OFED compat layer implementation.
This addresses some incorrect handling of IB MAD timeouts, since some IB
code depends on msecs_to_jiffies(0) returning 0.
MFC after: 1 week
Sponsored by: EMC / Isilon Storage Division
results.
Right now the scan infrastructure assumes the channel is under net80211
control, and that when receiving beacon frames for scanning, the
current channel is indeed what ic_curchan is set to.
But firmware NICs with firmware scan support need more than this -
they can do background scans whilst hiding the off-channel behaviour
from net80211. Ie, net80211 still thinks everything is associated
and on the main channel, but it's getting scan results from all the
background traffic.
However sta_add() pays attention to ic_curchan and discards scan
results that aren't on the right channel. CCK beacon frames can be
decoded from adjacent channels so the receive path and sta_add
discard these as appropriate. This is fine for software scanning
like for ath(4), but not for firmware NICs. So with those, the
whole concept of background firmware scanning won't work without
major hacks (eg, overriding ic_curchan before calling the beacon
input / scan add.)
As part of my scan overhaul, modify sta_add() and the scan_add()
APIs to take an explicit current channel. The normal RX path
will set it to ic_curchan so it's a no-op. However, drivers may
decide to (eventually!) override the scan method to set the
"right" current channel based on what the firmware reports the
scan state is.
So for example, iwn, rsu and other NICs will eventually do this:
* driver issues scan start firmware command;
* firmware sends a "scan start on channel X" notify;
* firmware sends a bunch of beacon RX's as part of
the scan results;
* .. and the driver will replace scan_add() curchan with channel X,
so scan results are correct.
* firmware sends a "scan start on channel Y" notify;
* firmware sends more beacons...
* .. the driver replaces scan_add() curchan with channel Y.
Note:
* Eventually, net80211 should eventually grow the idea of a per-packet
current channel. It's possible in various modes (eg WAVE, P2P, etc)
that individual frames can come in from different channels and that
is under firmware control rather than driver/net80211 control, so
we should support that.
lies within the last block of the bit set and no bits are set beyond the
offset, terminate the search immediately instead of continuing as though
there are further blocks in the set and subsequently returning an incorrect
result.
MFC after: 1 week
Sponsored by: EMC / Isilon Storage Division
list of pending dynamic type definitions, a match on the type name is not
sufficient - we need to compare the type encodings as well. For example,
bitfields have their own distinct type definitions which share the name of
the underlying integer type, and these types aren't generally
interchangeable.
This bug was causing the following libdtrace error when attempting to trace
the th_flags member of a struct tcphdr:
cg: bad field: off 104 type <32877> bits 539620016
Reported by: rwatson
MFC after: 3 weeks
