in lpd. Stat.recv is useful on a printserver, as something of a network
performance-monitoring tool. Stat.send is a minimal accounting record of
sorts for jobs going to tcp/ip based printers.
Reviewed by: freebsd-print@bostonradio.org
While here, I also updated the kernel config style, although I wouldn't
recommend doing this for the whole of section 4 yet, since our kernel
config style is still in a state of flux.
out of fashion. This particular case, unlike joy(8) and friends which
are just plain silly, did more than just load a kernel loadable module.
However, /etc/rc and the linux_base port were adjusted a while back to
cope with the absence of this script.
The only outstanding reason to hang on to it would have been for the
linux(8) manual page, which clued folks into the existence of the
Linuxulator. A new linux(4) was introduced a while back. It does
a much better job.
This script just isn't useful any more.
a per program basis allowing a greater control on what is built.
The buildopts file contains Makefile lines of form:
# Anything added to OPTS is added to every build rule.
OPTS= -DNOPAM
# These should only be added to the build of user-ppp.
ppp_OPTS= -DNOKLDLOAD -DNOINET6 -DNONAT -DNOATM -DNOSUID \
-DHAVE_DES -DNORADIUS -DNOI4B -DNONETGRAPH
Really these should be added to crunch.inc, but that file is currently
optional, and if defined masks the global one. Next step will be to move
these global settings back out into the individual builds as OPTS, and
then migrate OPTS and prog_OPTS back into the local crunch.inc file.
This software is obsolete, and its successor has interested parties
looking at it. Even if nobody was looking at kgzip, this utility
still wouldn't be useful in an environment where aout kernels
are a thing of the past.
PR: 20643
Submitted by: Peter Pentchev <roam@orbitel.bg>
it again and again, practically begging the Bad Man to insert his symlink
underneath it and send us down the path to oblivion.
Noticed by: David Lary <dlary@secureworks.net>
- Look for a hardwired interrupt in the routing table for this
bus/device/pin (we already did this).
- Look for another device with the same link byte which has a hardwired
interrupt.
- Look for a PCI device matching an entry with the same link byte
which has already been assigned an interrupt, and use that.
- Look for a routable interrupt listed in the "PCI only" interrupts
field and use that.
- Pick the first interrupt that's marked as routable and use that.
Also introduce a bunch of (missed?) macros and functions.
This man page still needs a lot of work, most likely a re-ordering
of the macros/functions, and a more complete, more accurate, listing of
available routines.
A good and worthy start nonetheless.
Xtal reference instead of the CLADI input.
In unframed E1 mode, tie SIGFRZ low so that the mysycc doesn't
get confused.
Don't mask errors with OOF. Don't ignore OOF errors.
Stop the channel before freeing mbufs in disconnect.
I still have no T1 devices to test with, so the T1 code is non-existent.
argument. These flags include INTR_FAST, INTR_MPSAFE, etc.
- Properly handle INTR_EXCL when it is passed in to allow an interrupt
handler to claim exclusive ownership of an interrupt thread.
- Add support for psuedo-fast interrupts on the alpha. For fast interrupts,
we don't allocate an interrupt thread; instead, during dispatching of an
interrupt, we run the handler directly instead of scheduling the thread
to run. Note that the handler is currently run without Giant and must be
MP safe. The only fast handler currently is for the sio driver.
Requested by: dfr
multicast filter on the Pegasus chip. Since IPv6 depends a lot
on multicasting, this caused several failures for people trying to
use IPv6 with Pegasus USB ethernet devices.
Submitted by: Jun Kuriyama <kuriyama@FreeBSD.org>
