command config register. At the present, this represents a nop
because these bits should have been set earlier in the process. In
the future, we'll only set these bits when the driver requests the
resource, not when the bus code detects the resource.
Reviewed by: mdodd
network layer (ether).
- Don't abuse module names to facilitate ifconfig module loading;
such abuse isn't really needed. (And if we do need type information
associated with a module then we should make it explicit and not
use hacks.)
PCIM_CMD_MEMEN and PCIM_CMD_BUSMASTEREN, becaise some braindead
BIOSes (such as one found in my vprmatrix notebook) forget
to initialize it properly resulting in attachment failure.
the list of supported sleep state.
This should help people understand what following message means.
acpi0: AcpiGetSleepTypeData failed - AE_NOT_FOUND
MFC after: 3 days
- Remove a useless device_is_alive() check.
- Disable interrupts if bus_child_present() so that this
check is more useful.
This fixes the hangs I was seeing when unloading the fxp driver.
Suggestions from: hsu, njl
- Be sure to teardown the interrupt first so that "kldunload if_fxp"
doesn't panic the box. It's now deadlocking rather than crashing,
which isn't really better, but I'm unsure this is fxp(4)'s fault.
- Change a bus_dmamap_sync() call to also do a BUS_DMASYNC_PREREAD
now that we can pass several operations.
is required. NetBSD has one because it checks for the mac address
match as well wanting to give its own string in the description.
Since we do neither, we don't need a separate entry.
# I suspect that a few of the COREGA cards might fall into that category
# as well, but since I don't have access to any of them it is hard to know
# for sure.
enet_mcast fields, so remove them. Sort. Eliminate now duplicate
entries.
This reorg saves about 500 bytes in the binary. I've tested this only
with a couple of cards, so please let me know if I've broken anything.
1.182; christos
A cardflash NE2000 from Michael Francini
1.181; perry
support Corega PCCL-11 -- from Christopher SEKIYA in PR 20932
1.180; ichiro
add product TOSHIBA PA2673U CBIDE2 (IODATA OEM)
1.179; kanaoka
Add SMC 8041TX 10/100 Ether PC Card.
0 in a problem that is being discussed. That means that the test for
product != 0 may cause problems. Looking at pccarddevs (which i
should have done earlier) we see:
product BONDWELL B236 0x0000 Game Card Joystick
product CONTEC CNETPC 0x0000 Contec C-NET(PC)C
product IBM MICRODRIVE 0x0000 IBM Microdrive
product RAYTHEON WLAN 0x0000 WLAN Adapter
product SOCKET EA_ETHER 0x0000 Socket Communications EA
product TDK LAK_CD011WL 0x0000 TDK LAK-CD011WL
so use only the vendor field for the end sentinel.
- Don't bother setting OACTIVE when the descriptors are all full
or there's a vr_encap failure, it doesn't help anything.
- Correctly roll back on the descriptor list after a failure
so as not to corrupt the list.
- Add a missing VR_UNLOCK().
Without these changes, vr_encap failure (which is assured during
a low mbuf situation) would result in the card locking until
the watchdog could fire.
MFC after: 1 week
Boost sample rate to 1.25 MSPS since that allows us to use a 5Mhz
(/4) or 10Mhz (/8) external clock.
Make the interrupt both MPSAFE and FAST, at 610 interrupts a second,
and a max time to service of 5 msec, we brake for nobody.
Use kernel thread to accumulate into the 25 possible wave signals.
Use #ifdef _KERNEL to let .c file double as .h file defining the ioctls.
of the entries have a description, we'll use that to override the
description that the pccard layer generates for us.
This saves about 930 bytes in the module, so I feel it won't hurt the
crowded boot disks....
# other modules to follow
of asserting that an mbuf has a packet header. Use it instead of hand-
rolled versions wherever applicable.
Submitted by: Hiten Pandya <hiten@unixdaemons.com>
