This closes a minor information leak which allows a remote observer to
determine the rate at which the machine is generating packets, since the
default behaviour is to increment a counter for each packet sent.
Reviewed by: -net
Obtained from: OpenBSD
gigabit ethernet controller chip. This device is used on some
fiber optic gigE cards from SMC, D-Link and Addtron. Jumbograms and
TCP/IP checksum offload on receive are supported. Hardware VLAN
filtering is not, because it doesn't play well with our existing
VLAN code. Also add manual page.
There is a 4.x version of this driver available at
http://www.freebsd.org/~wpaul/Level1/4.x if anyone feels adventurous
and wants to test it. I still need to do performance testing and
tuning with this device.
(For my next trick, I will make the 3Com 3cR990 sit up and beg.)
Add a CAPI (hardware independent) driver i4bcapi(4) and hardware driver
iavc (4) to support active CAPI-based BRI and PRI cards (currently AVM
B1 and T1 cards) to isdn4bsd.
systems were repo-copied from sys/miscfs to sys/fs.
- Renamed the following file systems and their modules:
fdesc -> fdescfs, portal -> portalfs, union -> unionfs.
- Renamed corresponding kernel options:
FDESC -> FDESCFS, PORTAL -> PORTALFS, UNION -> UNIONFS.
- Install header files for the above file systems.
- Removed bogus -I${.CURDIR}/../../sys CFLAGS from userland
Makefiles.
If for some reason DEVFS is undesired, the "NODEVFS" option is
needed now.
Pending any significant issues, DEVFS will be made mandatory in
-current on july 1st so that we can start reaping the full
benefits of having it.
and DP83821 gigabit ethernet MAC chips and the NatSemi DP83861 10/100/1000
copper PHY. There are a whole bunch of very low cost cards available with
this chipset selling for $150USD or less. This includes the SMC9462TX,
D-Link DGE-500T, Asante GigaNIX 1000TA and 1000TPC, and a couple cards
from Addtron.
This chip supports TCP/IP checksum offload, VLAN tagging/insertion.
2048-bit multicast filter, jumbograms and has 8K TX and 32K RX FIFOs.
I have not done serious performance testing with this driver. I know
it works, and I want it under CVS control so I can keep tabs on it.
Note that there's no serious mutex stuff in here yet either: I need
to talk more with jhb to figure out the right way to do this. That
said, I don't think there will be any problems.
This driver should also work on the alpha. It's not turned on in
GENERIC.
This driver supports PCI Xr-based and ISA Xem Digiboard cards.
dgm will go away soon if there are no problems reported. For now,
configuring dgm into your kernel warns that you should be using
digi. This driver is probably close to supporting Xi, Xe and Xeve
cards, but I wouldn't expect them to work properly (hardware
donations welcome).
The digi_* pseudo-drivers are not drivers themselves but contain
the BIOS and FEP/OS binaries for various digiboard cards and are
auto-loaded and auto-unloaded by the digi driver at initialisation
time. They *may* be configured into the kernel, but waste a lot
of space if they are. They're intended to be left as modules.
The digictl program is (mainly) used to re-initialise cards that
have external port modules attached such as the PC/Xem.
interfaces and functionality intended for use during correctness and
regression testing. Features enabled by "options REGRESSION" may
in and of themselves introduce security or correctness problems if
used improperly, and so are not intended for use in production
systems, only in testing environments.
Obtained from: TrustedBSD Project
Add simple "xlat" converter which performs 8to8 table based conversion.
Unicode converter will be added in the near future.
Reviewed by: silence on arch@
Files placement reviewed by: bde
Obtained from: smbfs
very specific scenarios, and now that we have had net.inet.tcp.blackhole for
quite some time there is really no reason to use it any more.
(first of three commits)
killing ipv6 and some other things.
This makes GENERIC and NEWCARD the same, with OLDCARD stuff commented
out and the NEWCARD stuff included. For the moment, pcic is commented
out (which has a old). Plus invariants. Plus ddb.
bolted to a ne-2000 chip. This is necessary for the NetGear FA-410TX
and other cards.
This also requires you add mii to your kernel if you have an ed driver
configured.
This code will result in a couple of timeout messages for ed on the
impacted cards. Additional work will be needed, but this does work
right now, and many people need these cards.
Submitted by: Ian Dowse <iedowse@maths.tcd.ie>
rather than in silly places like "VFS Cluster debugging". People
should really be using COMPAT_LINUX instead of the linux module on
dynamic systems like -current.
depend on this. The linux ABI emulator tries to use it for some linux
binaries too. VM86 had a bigger cost than this and it was made default
a while ago.
Reviewed by: jhb, imp
to 1GB. A box of mine is running with MAXDSIZ and DFLDSIZ increased
up to 1.5GB.
Wishlist: It would be nice to warn if MAXTSIZ + MAXDSIZ + MAXSSIZ
exceeds VM_MAXUSER_ADDRESS - VM_MINUSER_ADDRESS.
