This works similar to WITH_SYSTEM_COMPILER added in r300354. It only
supports lld via WITH_LLD_BOOTSTRAP.
When both SYSTEM_COMPILER and SYSTEM_LINKER logic passes then libclang
will not build in cross-tools. If either check fails though then
libclang is built.
The .info is reworked to notify when libclang will be built since if
either clang or lld needs to be rebuilt, but not the other, the
notification can lead to confusion on why "clang is building".
-fuse-ld= is not used with this method so some combinations of compiler
and linker are expected to fail.
A new 'make test-system-linker' target is added to see the logic results.
Makefile.inc1:
CROSS_BINUTILS_PREFIX support had to be moved higher up so that XLD
could be set and MK_LLD_BOOTSTRAP disabled before checking SYSTEM_LINKER
logic as done with SYSTEM_COMPILER. This also required moving where
bsd.linker.mk was read since XLD needs to be set before parsing it. This
creates a situation where src.opts.mk can not test LINKER_FEATURES or
add LLD_BOOTSTAP to BROKEN_OPTIONS.
Reviewed by: emaste (earlier version)
Sponsored by: Dell EMC
Differential Revision: https://reviews.freebsd.org/D15894
lld always needs these DWARF sources, as well as other default and extra
tools. XDL seems to be the best fit list.
Remove MK_LLD_IS_LD check from SRCS_MIW which is now reduced to just a
few files for llvm-objdump.
Sponsored by: Dell EMC
Differential Revision: https://reviews.freebsd.org/D15915
MK_LLD is for the installed lld while MK_LLD_BOOTSTRAP is for the build
tool. For WITH_SYSTEM_LINKER it is necesarry to separate the logic of
these two. When building libllvm TOOLS_PREFIX will be defined and
MK_LLD_BOOTSTRAP should be checked instead.
Sponsored by: Dell EMC
Differential Revision: https://reviews.freebsd.org/D15837
LLD_BOOTSTRAP (build) is independent of LLD_IS_LD (installed) so they
should not be based on each other.
This is related to upcoming WITH_SYSTEM_LINKER work.
Reviewed by: emaste
Sponsored by: Dell EMC
Differential Revision: https://reviews.freebsd.org/D15836
This is needed for efifb.
arm and ricv pmap (the two arch with arm64 that uses subr_devmap) have very
different implementation so for now only add this for arm64.
Tested with efifb on Pine64 with a few other patches.
Reviewed by: cognet
Differential Revision: https://reviews.freebsd.org/D15294
The values for tx/rx delays differs accross the different DTS.
Mainline Linux set it to 0x24/0x18
Mostly-Vendor u-boot (the one maintained and developped) to 0x18/0x18
Mostly-Vendor linux (the one maintained and developped) to 0x26/0x11
By experience only 0x18/0x18 works so until the issue is resolved rely on
the bootloader settings.
The property are named {t,r}x_delay and not {t,r}-delay.
The upper bits of the register are a mask of which bits is allowed
to be written, set it otherwise we write nothing.
OF_getencprop returns <0 = for an error.
Pointy Hat: myself
Reported by: jmcneill (delay and mask bits)
Summary: In order to use cpufreq(4), a dev.cpu attachment must be created. If
the IBM property is found denoting SMT, attach only to the first thread setup,
so that a cpufreq device can bind.
Reviewed by: nwhitehorn
Differential Revision: https://reviews.freebsd.org/D15921
to FOREACH_PROC_IN_SYSTEM() to have a single pattern to look for.
Reviewed by: kib
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
Differential Revision: https://reviews.freebsd.org/D15916
Implement a ddb function walking the namecache to do this.
Reviewed by: jhb, mjg
Inspired by: gdb macro from jhb (old version)
Sponsored by: iXsystems, Inc.
Differential Revision: https://reviews.freebsd.org/D14898
fsid_t and ino_t are 64-bit entities, use uintmax_t typecast to ensure we
can print it on 32-bit or 64-bit architectures by using the %ju format for
prints.
Obtained from: Juniper Networks, Inc.
Observe:
printf "a\nb\nc\n" > /tmp/foo
# Next command results in no output
cat /tmp/foo | sort -m
# Next command results in proper output
cat /tmp/foo | sort -m -
# Also works:
sort -m /tmp/foo
Some const'ification was done to simplify the actual solution of adding "-"
explicitly to the file list if we didn't have any file arguments left over.
PR: 190099
MFC after: 1 week
containing paths, fingerprints, and optional option flags which in turn
get pushed into the MAC/veriexec meta-data store via the veriexec device.
The format of the fingerprints file is as follows:
path type fingerprint options
The type of fingerprint supported depends on what MAC/veriexec fingerprint
modules have been loaded into the system. The veriexecctl application is
able to determine which ones are available by consulting the
security.mac.veriexec.algorithms sysctl.
The following options are currently supported in MAC/veriexec and by the
veriexecctl application:
indirect
If this option is set then the executable cannot be invoked directly, it
can only be used as an interpreter in shell scripts.
file
Indicates that the fingerprint is associated with a file, not an
executable. Files have their fingerprints verified during open(2) and are
automatically made read only. This option may be used to verify shared
libraries have not been tampered with.
no_ptrace
If this option is set then the executable cannot be traced with the
ptrace(2) process tracing and debugging call.
trusted
If this option is set then the executable is allowed to write to the
mem(4) devices. By default, when verified execution is enforced, no
process is allowed to write to the mem(4) devices.
The options are not case sensitive.
Reviewed by: jtl, wblock
Obtained from: Juniper Networks, Inc.
Differential Revision: https://reviews.freebsd.org/D8575
or paths to see if they can be verified by MAC/veriexec.
Reviewed by: jtl, wblock
Obtained from: Juniper Networks, Inc.
Differential Revision: https://reviews.freebsd.org/D8562
The veriexec device features the following ioctl commands:
VERIEXEC_ACTIVE
Activate veriexec functionality
VERIEXEC_DEBUG_ON
Enable debugging mode and increment or set the debug level
VERIEXEC_DEBUG_OFF
Disable debugging mode
VERIEXEC_ENFORCE
Enforce veriexec fingerprinting (and acitvate if not already)
VERIEXEC_GETSTATE
Get current veriexec state
VERIEXEC_LOCK
Lock changes to veriexec meta-data store
VERIEXEC_LOAD
Load veriexec fingerprint if secure level is not raised (and passes the
checks for VERIEXEC_SIGNED_LOAD)
VERIEXEC_SIGNED_LOAD
Load veriexec fingerprints from loader that supports signed manifest
(and thus we can be more lenient about secure level being raised.)
Fingerprints can be loaded if the meta-data store is not locked. Also
securelevel must not have been raised or some fingerprints must have
already been loaded, otherwise it would be dangerous to allow loading.
(Note: this assumes that the fingerprints in the meta-data store at
least cover the fingerprint loader.)
Reviewed by: jtl
Obtained from: Juniper Networks, Inc.
Differential Revision: https://reviews.freebsd.org/D8561
framework.
The code is organized into a few distinct pieces:
* The meta-data store (in veriexec_metadata.c) which maps a file system
identifier, file identifier, and generation key tuple to veriexec
meta-data record.
* Fingerprint management (in veriexec_fingerprint.c) which deals with
calculating the cryptographic hash for a file and verifying it. It also
manages the loadable fingerprint modules.
* MAC policy implementation (in mac_veriexec.c) which implements the
following MAC methods:
mpo_init
Initializes the veriexec state, meta-data store, fingerprint modules,
and registers mount and unmount EVENTHANDLERs
mpo_syscall
Implements the following per-policy system calls:
MAC_VERIEXEC_CHECK_FD_SYSCALL
Check a file descriptor to see if the referenced file has a valid
fingerprint.
MAC_VERIEXEC_CHECK_PATH_SYSCALL
Check a path to see if the referenced file has a valid fingerprint.
mpo_kld_check_load
Check if loading a kld is allowed. This checks if the referenced vnode
has a valid fingerprint.
mpo_mount_destroy_label
Clears the veriexec slot data in a mount point label.
mpo_mount_init_label
Initializes the veriexec slot data in a mount point label.
The file system identifier is saved in the veriexec slot data.
mpo_priv_check
Check if a process is allowed to write to /dev/kmem and /dev/mem
devices.
If a process is flagged as trusted, it is allowed to write.
mpo_proc_check_debug
Check if a process is allowed to be debugged. If a process is not
flagged with VERIEXEC_NOTRACE, then debugging is allowed.
mpo_vnode_check_exec
Check is an exectuable is allowed to run. If veriexec is not enforcing
or the executable has a valid fingerprint, then it is allowed to run.
NOTE: veriexec will complain about mismatched fingerprints if it is
active, regardless of the state of the enforcement.
mpo_vnode_check_open
Check is a file is allowed to be opened. If verification was not
requested, veriexec is not enforcing, or the file has a valid
fingerprint, then veriexec will allow the file to be opened.
mpo_vnode_copy_label
Copies the veriexec slot data from one label to another.
mpo_vnode_destroy_label
Clears the veriexec slot data in a vnode label.
mpo_vnode_init_label
Initializes the veriexec slot data in a vnode label.
The fingerprint status for the file is stored in the veriexec slot data.
* Some sysctls, under security.mac.veriexec, for setting debug level,
fetching the current state in a human-readable form, and dumping the
fingerprint database are implemented.
* The MAC policy implementation source file also contains some utility
functions.
* A set of fingerprint modules for the following cryptographic hash
algorithms:
RIPEMD-160, SHA1, SHA2-256, SHA2-384, SHA2-512
* Loadable module builds for MAC/veriexec and fingerprint modules.
WARNING: Using veriexec with NFS (or other network-based) file systems is
not recommended as one cannot guarantee the integrity of the files
served, nor the uniqueness of file system identifiers which are
used as key in the meta-data store.
Reviewed by: ian, jtl
Obtained from: Juniper Networks, Inc.
Differential Revision: https://reviews.freebsd.org/D8554
This was causing issues for people booting.
I will likely bring this back as an optional feature, similar to
boot0sio, like gptboot-serial or something.
PR: 221526
Reported by: O. Hartmann <ohartmann@walstatt.org>, Thomas Laus <lausts@acm.org>
It is XCC used during the build of target binaries that replaces the
bootstrap compiler.
Also slightly tweak style.
MFC after: 2 weeks
Sponsored by: Dell EMC
This could lead to 'sh: head: not found' warnings which were a symptom
of running 'ld --version' during installworld. This was only happening
with XCC or XLD set. It is intended that cc and ld do not run during
installworld. The metadata for these are already stored in
compiler-metadata.mk added in r316794.
This also removes redundant CROSSENV additions that were for
WITH_SYSTEM_COMPILER, WITHOUT_CROSS_COMPILER, and WITHOUT_TOOLCHAIN
which all don't have a cc or ld in their PATH during install.
Reported by: Mark Millard
MFC after: 2 weeks
Sponsored by: Dell EMC
Linux 2.6.26 introduced 64-bit capability sets. Extend our stub
implementation to handle both 32- and 64-bit. (We still report no
capabilities in capget, and disallow any in capset.)
Reviewed by: chuck
Sponsored by: Turing Robotic Industries Inc.
Differential Revision: https://reviews.freebsd.org/D15887
try to build them if MK_OPENSSL is unset.
Reviewed by: emaste imp kevans
Sponsored by: Limelight Networks
Differential Revision: https://reviews.freebsd.org/D15211
Unlike SD cards, that publish RCA in response to CMD3,
MMC cards expect the host to set RCA itself.
Since we don't support multiple MMC cards on the bus,
just assign a static RCA of 2 to the attached MMC card.
Approved by: imp (mentor)
Differential Revision: https://reviews.freebsd.org/D13063
Many licenses on ar files contained small variations from the standard
FreeBSD license text. To avoid license proliferation switch to the usual
standard 2-clause FreeBSD license for those files where I have obtained
permission from all of the listed copyright holders.
Approved by: jkoshy, kaiw
Differential Revision: https://reviews.freebsd.org/D14561
Includes utimes(2), futimes(2), lutimes(2), futimesat(2), mprotect(2), and
undelete(2). undelete, for now, is tested only in failure mode.
Submitted by: aniketp
MFC after: 2 weeks
Sponsored by: Google, Inc. (GSoC 2018)
Differential Revision: https://reviews.freebsd.org/D15893
o Restore floating-point registers in jumpto()
These are required to native cross build GCC and GDB
(both do require libc++ and libunwind).
These are not tested.
Sponsored by: DARPA, AFRL
