there are stubs compiled into the kernel if BPF support is not enabled,
there aren't any problems with unresolved symbols. The modules in /modules
are compiled with BPF support enabled anyway, so the most this will do is
bloat GENERIC a little.
declaration for the interface driver from "foo" to "if_foo" but leave the
declaration for the miibus attached to the interface driver alone. This
lets the internal module name be "if_foo" while still allowing the miibus
instances to attach to "foo."
This should allow ifconfig to autoload driver modules again without
breaking the miibus attach.
This whole idea isn't going to work until somebody makes the bus/kld
code smarter. The idea here is to change the module's internal name
from "foo" to "if_foo" so that ifconfig can tell a network driver from
a non-network one. However doing this doesn't work correctly no matter
how you slice it. For everything to work, you have to change the name
in both the driver_t struct and the DRIVER_MODULE() declaration. The
problems are:
- If you change the name in both places, then the kernel thinks that
the device's name is now "if_foo", so you get things like:
if_foo0: <FOO ethernet> irq foo at device foo on pcifoo
if_foo0: Ethernet address: foo:foo:foo:foo:foo:foo
This is bogus. Now the device name doesn't agree with the logical
interface name. There's no reason for this, and it violates the
principle of least astonishment.
- If you leave the name in the driver_t struct as "foo" and only
change the names in the DRIVER_MODULE() declaration to "if_foo" then
attaching drivers to child devices doesn't work because the names don't
agree. This breaks miibus: drivers that need to have miibuses and PHY
drivers attached never get them.
In other words: damned if you do, damned if you don't.
This needs to be thought through some more. Since the drivers that
use miibus are broken, I have to change these all back in order to
make them work again. Yes this will stop ifconfig from being able
to demand load driver modules. On the whole, I'd rather have that
than having the drivers not work at all.
in 4 byte chunks. It turns out that with the 82c169C on the Netgear
FA-310TX Rev D2, if you tell the chip you have reserved a buffer of 1518
bytes, it will actually treat it as 1516 bytes since 1518 is divisible
by four. Consequently, a packet of 1514 bytes will always end up consuming
two buffers: the last coupleof bytes will spill over into the next
descriptor. This causes the pn_rx_bug_war() routine to trip unnecessarily.
I'm not sure if the 82c169B or 82c168 chips behave the same way; I'll
have to check them. In any case, this change should work just as well
with them. Note that the FA-310TX Rev D2 also has a Broadcom PHY
instead of a Level One LXT970 PHY, however this shouldn't make any
difference as far as the driver is concerned.
This change also allows me to do a way with one rounding overation in
pn_rx-buf_war().
compiles cleanly on the Alpha. (On the alpha, the port type is an int,
not a short).
Cast a couple of pointers to ints via 'uintptr_t' rather than 'unsigned
int' since uintptr_t is long (64 bit) on Alpha, as are pointers.
similar to the PNIC I (supported by the pn driver). In fact, it's really
a Macronix 98715A with wake on LAN support added. According to LinkSys,
the PNIC II was jointly developed by Lite-On and Macronis. I get the
feeling Macronix did most of the work. (The datasheet has the Macronix
logo on it, and is in fact nearly identical to the 98715 datasheet, except
for the extra wake on LAN registers.) In any case, the PNIC II works just
fine with the Macronix driver.
The changes are:
- Move PCI ID for the PNIC II from the pn driver to the mx driver.
- Mention PNIC II support in mx.4.
- Mention PNIC II support in RELNOTES.TXT and HARDWARE.TXT.
#define COMPAT_PCI_DRIVER(name,data) DATA_SET(pcidevice_set,data)
.. to 2.2.x and 3.x if people think it's worth it. Driver writers can do
this if it's not defined. (The reason for this is that I'm trying to
progressively eliminate use of linker_sets where it hurts modularity and
runtime load capability, and these DATA_SET's keep getting in the way.)
i386 platform boots, it is no longer ISA-centric, and is fully dynamic.
Most old drivers compile and run without modification via 'compatability
shims' to enable a smoother transition. eisa, isapnp and pccard* are
not yet using the new resource manager. Once fully converted, all drivers
will be loadable, including PCI and ISA.
(Some other changes appear to have snuck in, including a port of Soren's
ATA driver to the Alpha. Soren, back this out if you need to.)
This is a checkpoint of work-in-progress, but is quite functional.
The bulk of the work was done over the last few years by Doug Rabson and
Garrett Wollman.
Approved by: core
transceiver. Note in the manual page that autoselection doesn't
work on the 82c168 because the built-in NWAY support is horribly
broken. Manual mode selection works fine, but autoneg is broken for
everything except maybe 10Mbps half-duplex. There's no simple way
to fix this at the moment, so I have to settle for documenting the
bug for now. Fortunately, there aren't anywhere near as many 82c168
boards around as there are 82c169s.
- It turns out that the 'promiscuous mode' bug what I discovered with the
PNIC is not restricted to promiscuous mode. I've been doing some remote
debugging for someone with a P75 system, and at 100Mbps, the receiver
screws up even when the NIC is in normal mode. Thus, enable the workaround
for this bug all the time. Note that the workaround is still not enabled
for the PNIC II, since I haven't tested one yet.
- Set the 'arbitration' bit in the bus configuration register and set the
maximum burst size to 16 longwords. This seems to fix problems with
transmit corruption on the P75 system mentioned above. (It probably hurts
performance a bit too, but I've given up trying to make the PNIC perform
well.)
transceiver. Thanks to Brian Walenze for donating a NIC with this chip
on it (LinkSys didn't really sell that many of them and they're not
in production anymore). The driver now distinguishes between the
82c168 and 82c169 when probing. If no MII transceiver is detected,
it switches over to using the internal one.
sys/alpha/conf/GENERIC.
Note: the PNIC ignores the lower few bits of the RX buffer DMA address,
which means we have to add yet another kludge to make it happy. Since
we can't offset the packet data, we copy the first few bytes of the
received data into a separate mbuf with proper alignment. This puts
the IP header where it needs to be to prevent unaligned accesses.
Also modified the PNIC driver to use a non-interrupt driven TX
strategy. This improves performance somewhat on x86/SMP systems where
interrupt delivery doesn't seem to be as fast with an SMP kernel as
with a UP kernel.
isolated to revision 33 PNIC chips is also present in revision 32 chips.
Cards with rev. 32 chips include the LinkSys LNE100TX and the Matrox
FastNIC 10/100. This accounts for all the cards that I have to test
with.
(I was never able to personally trip the bug on this chip rev, but today
one of the guys in the lab did it with the software they're working on
for their cellular IP project, which uses BPF and promiscuous mode
extensively.)
This commit enables the promiscuous mode software workaround code for
both revison 32 and revision 33 chips. It's possible all of the PNIC
chips suffer from this bug, but these are the only two revs where I
know for a fact it exists.
chip revisions. (A buggy taiwanese chip? I'm just shocked; shocked I tell
you.) So far I have only observed the anomalous behavior on board with
PCI revision 33 chips. At the moment, this seems to include only the
Netgear FA310-TX rev D1 boards with chips labeled NGMC169B. (Possibly this
means it's an 82c169B part from Lite-On.)
The bug only manifests itself in promiscuous mode, and usually only at
10Mbps half-duplex. (I have not observed the problem in full-duplex mode,
and I don't think it ever happens at 100Mbps.) The bug appears to be in
the receiver DMA engine. Normally, the chip is programmed with a linked
list of receiver descriptors, each with a receive buffer capable of holding
a complete full-sized ethernet frame. During periods of heavy traffic
(i.e. ping -c 100 -f 8100 <otherhost>), the receiver will sometimes appear
to upload its entire FIFO memory contents instead of just uploading the
desired received frame. The uploaded data will span several receive
buffers, in spite of the fact that the chip has been told to only use
one descriptor per frame, and appears to consist of previously transmitted
frames with the correct received frame appended to the end.
Unfortunately, there is no way to determine exactly how much data is
uploaded when this happens; the chip doesn't tell you anything except the
size of the desired received frame, and the amount of bogus data varies.
Sometimes, the desired frame is also split across multiple buffers.
The workaround is ugly and nasty. The driver assembles all of the data
from the bogus frames into a single buffer. The receive buffers are always
zeroed out, and we program the chip to always include the receive CRC
at the end of each frame. We therefore know that we can start from the
end of the buffer and scan back until we encounter a non-zero data byte,
and say conclusively that this is the end of the desired frame. We can
then subtract the frame length from this address to determine the real
start of the frame, and copy it into an mbuf and pass it on.
This is kludgy and time consuming, but it's better than dropping frames.
It's not too bad since the problem only happens at 10Mbps.
The workaround is only enabled for chips with PCI revision == 33. The
LinkSys LNE100TX and Matrox FastNIC 10/100 cards use a revision 32 chip
and work fine in promiscuous mode. Netgear support has confirmed that
they "have some previous knowledge of problems in promiscuous mode" but
didn't have a workaround. The people at Lite-On who would be able to
suggest a possible fix are on vacation. So, I decided to implement a
workaround of my own until I hear from them. I suppose this problem made
it through Netgear's QA department since Windows doesn't normally use
promiscuous mode, and if Windows doesn't need the feature than it can't
possibly be important, right? Grrr.
apparently possible) event that the transmit start routine is
called with and empty if_snd queue, bail out instead of dereferencing
unilitialized transmit list pointers and panicking.
PCI fast ethernet adapters, plus man pages.
if_pn.c: Netgear FA310TX model D1, LinkSys LNE100TX, Matrox FastNIC 10/100,
various other PNIC devices
if_mx.c: NDC Communications SOHOware SFA100 (Macronix 98713A), various
other boards based on the Macronix 98713, 98713A, 98715, 98715A
and 98725 chips
if_vr.c: D-Link DFE530-TX, other boards based on the VIA Rhine and
Rhine II chips (note: the D-Link and certain other cards
that actually use a Rhine II chip still return the PCI
device ID of the Rhine I. I don't know why, and it doesn't
really matter since the driver treats both chips the same
anyway.)
if_wb.c: Trendware TE100-PCIE and various other cards based on the
Winbond W89C840F chip (the Trendware card is identical to
the sample boards Winbond sent me, so who knows how many
clones there are running around)
All drivers include support for ifmedia, BPF and hardware multicast
filtering.
Also updated GENERIC, LINT, RELNOTES.TXT, userconfig and
sysinstall device list.
I also have a driver for the ASIX AX88140A in the works.
