SK-NET GENESIS document says reading SK_ISSR should stop generating
further interrupts(Since we drop a driver lock before invoking
ifp->if_input handler we should disable interrupts in ISR in order
to protect integrity of softc from subsequent interrupts). But it
seems that there is possibility of loosing interrupts between
reading SK_ISSR and determining which interrupts are reported.
To cope with the situation we continuously read SK_ISSR register
until there are no interrupts. However, it seems that the above
work around doesn't fix all cases. To protect watchdog handler
from triggering false alarm add a work around code which try to
reclaim pending Tx descriptors before resetting hardware. This
should fix occasional watchdog timeout errors seen on this driver.
Reported by: Frank Behrens <frank AT pinky dot sax dot de >
Tested by: Frank Behrens <frank AT pinky dot sax dot de >
undocumented HISTORICAL_MAKE_WORLD variable and set it. Note it
here so the blow up will not really be a surprise to people who
read.
Link the buildingworld chapter of our handbook in the README
while I'm here.
parameter to try to delete an NFS export. It won't work, and will log
a spurious warning to syslog.
Tested by: Arno J. Klaassen <arno at heho dot snv dot jussieu dot fr>
MFC after: 3 days
environment for cross building (the same one you'd get interactively
in make buildenv). This cannot be a simple
make -f Makefile.inc1 -V WMAKEENV
because in PATH is not set correctly unless one takes a trip through
the Makefile/Makefile.inc1 indirection, the logic of which is too
large to reproduce outside of Makefiles.
taskqueued interrupt mode is going to be quite complex. Since
the polling mode is considered legacy feature for em(4) driver,
the decision is made to make polling and new interrupt handler
mutually exclusive, selected at compile time.
If kernel is compiled with DEVICE_POLLING, the fast taskqueued
interrupt handler code is disabled and the em_poll() and legacy
em_intr() functions are enabled. Otherwise, legacy functions
are disabled and only em_intr_fast() code is compiled.
Discussed with: scottl
- K&R -> ANSI prototype [O]
- Do not bother to do free right before exit() or execve() [O]
- Remove some dead code in addarg()
- Make additional parameters specified in mailer.conf(5)
actually work and document the fact. [N]
- Avoid using __progname but instead use getprogname()
and setprogname() to provide more sensible messages. [O, N]
- Update $OpenBSD$ and $NetBSD$ to reflect the fact that we
have sync'ed with their code.
- WARNS=6
Obtained from/Inspired by: OpenBSD [O], NetBSD [N] (partially)
Clean out the abortive start to homegrown, per-mpt,
Domain Validation. This should really be done at a
higher level.
Use the PIM_SEQSCAN flag for U320- this seems to correct
cases of being unable to consistently negotiate U320 in
the cases where I'd seen this before.
Between this and other recent checkins, this driver is
pretty close to being ready for MFC.
Reviewed by: scottl, ken, scsi@
MFC after: 1 week
what to do with it.
This forces us to scan targets sequentially, not in parallel.
The reason we might want to do this is that SPI negotiation
might not work right at the SIM level if we try to do it
in parallel. We *could* fix this for each SIM where this is
broken, but it's a lot harder to do that when we can simply
ask CAM to probe sequentially.
If PIM_SEQSCAN is not set (default), the original behaviour for
probing is unchanged.
LUN probing is still done in parallel for each target in either
case.
While we're at it, clean up some resource leakage for error
cases.
Reviewed by: ken, scott, scsi@
MFC after: 1 week
Now, encryption algorithm is given using '-e' option, not '-a'.
The '-a' option is now used to specify authentication algorithm.
Supported by: Wheel Sp. z o.o. (http://www.wheel.pl)