bit fileid's in NFSv2 and NFSv3. Without this fix, invalid casting (and sign
extension) was creating problems for any fileid greater than 2^31.
We discovered this because we have test clusters with more than 2 billion
allocated files and 64-bit ino_t's (and friend structures).
Reviewed by: rmacklem
Approved by: zml (mentor)
MFC after: 2 weeks
the iommu(4) provided one, i.e. in case of Hummingbird and Sabre bridges,
otherwise just use the iommu(4) one. This also fixes a bug introduced in
r220039 which caused an empty DMA method table to be used for the second
of a pair of Psycho bridges.
and per-loginclass resource accounting information, to be used by the new
resource limits code. It's connected to the build, but the code that
actually calls the new functions will come later.
Sponsored by: The FreeBSD Foundation
Reviewed by: kib (earlier version)
in the RX path when doing 11n and block-ack'ed frames. Apparently, the MAC
will loop over that self-linked descriptor and treat it as "good enough"
for (incorrectly!) ACKing the frames in the block-ack.
Until I figure out how to work around this issue in the future, this counter
will tell me if packet RX processing ever gets to the point where it's
touching the self-linked descriptor. If there's ever enough packets to get
to that point, BA's will be invalid and likely very unhappy.
listing each card as it is found on non-PC98 (PC98 already had this).
- Increase the length of the DELAY() used before timing out while reading
PNP resource data.
Tested by: Steven Nikkel steven_nikkel ertyu org
MFC after: 1 week
of active DMA cycle. dc_setcfg() also has to wait until the DMA
engine is stopped so using a common function to handle the job is
better than duplicating the code.
No objection from: marius
makes controller to receive bad frames and i82557 will also receive
bad frames since fxp(4) have to receive VLAN oversized frames. If
fxp(4) encounter DMA overrun error, the received frame size would
be 0 so the actual frame size after checksum field extraction the
length would be negative(-2). Due to signed/unsigned comparison
used in driver, frame length check did not work for DMA overrun
frames. Correct this by casting it to int.
While I'm here explicitly check DMA overrun error and discard the
frame regardless of result of received frame length check.
Reported by: n_hibma
Tested by: n_hibma
MFC after: 1 week
I'll clear how it's supposed to work with Bernhard and then look
at enabling this in the correct situations.
But this -does- enable HT RTS protection (using the appropriate legacy
rates) if this bit of code is enabled.
instead of 0x100000. As a side effect, an amd64 kernel now loads at
physical address 0x200000 instead of 0x100000. This is probably for the
best because it avoids the use of a 2MB page mapping for the first 1MB of
the kernel that also spans the fixed MTRRs. However, getmemsize() still
thinks that the kernel loads at 0x100000, and so the physical memory between
0x100000 and 0x200000 is lost. Fix this problem by replacing the hard-wired
constant in getmemsize() by a symbol "kernphys" that is defined by the
linker script.
In collaboration with: kib
(e.g. powerpc64), this looks in a slightly different default path than now,
specifying both $MACHINE and $MACHINE_ARCH:
MIRROR/pub/FreeBSD/releases/`uname -p`/`uname -m`/`uname -r`
How to handle TBEMD properly probably merits some more discussion, but,
since no such 9.0-CURRENT distfiles exist at the moment, all existing
mirrors presently fail anyway.
registered in g_gate_units array and when its sc_provider field is
filled. If during this period g_gate_units is accessed by another
thread that is checking for provider name collision the crash is
possible.
Fix this by adding sc_name field to struct g_gate_softc. In
g_gate_create() when g_gate_softc is created but sc_provider is still
not sc_name points to provider name stored in the local array.
Approved by: pjd (mentor)
Reported by: Freddie Cash <fjwcash@gmail.com>
MFC after: 1 week
just for Redboot.
At some point we're going to need to build options for different
boot environments - for example, the UBoot setups I've seen simply
have the MAC address hard-coded at a fixed location in flash.
The OpenWRT support simply yanks the if_arge MAC directly from that
in code, rather than trying to find a uboot environment to pull it
from.
memory detected from Redboot, or overrides the "otherwise" case
if no Redboot information was found.
Some AR71XX platforms don't use Redboot (eg TP-LINK devices using
UBoot; some later Ubiquiti devices which apparently also use
UBoot) and at least one plain out lies - the Ubiquiti LS-SR71A
Redboot says there's 16mb of RAM when in fact there's 32mb.
A more "clean" solution will be needed at a later date.
The AR913x/AR724x USB lives at a different offset to the AR71xx
USB, so this needs to be either adjusted for in a subsequent
commit, or updated in hints for kernels compiled for those
platforms.
Submitted by: Luiz Otavio O Souzau <loos.br@gmail.com>
