does not guarantee established link. Also 1000baseT link report for
fast ethernet controller is not valid one so make sure gigabit link
is allowed for this controller.
Whenever we lost link, check whether Rx/Tx MACs were enabled. If both
MAC are not active, do not try to disable it again.
mark controller's capability. Controllers that have jumbo frame
support sets MSK_FLAG_JUMBO, and controllers that does not support
checksum offloading for jumbo frames will set MSK_FLAG_JUMBO_NOCSUM.
For Fast Ethernet controllers it will set MSK_FLAG_FASTETHER and it
would be used in link state handling.
While here, disable Tx checksum offloading if jumbo frame is used
on controllers that does not have Tx checksum offloading capability
for jumbo frame(e.g. Yukon EC Ultra).
FE+ controller. Due to the severe silicon bugs for Yukon FE+,
88E3016 seems to require more workarounds. However I'm not sure
whether the workaround is PHY specific or only applicable to Yukon
FE+. The datasheet for the PHY is publicly available but it lacks
several details for the workaround used in this change. The
workaround information was obtained from Linux. Many thanks to
Yukon FE+ users who helped me add 88E3016 support.
Tested by: bz, Tanguy Bouzeloc ( the.zauron <> gmail dot com )
Bruce Cran ( bruce <> cran dot org dot uk )
Michael Reifenberger ( mike <> reifenberger dot com )
Stephen Montgomery-Smith ( stephen <> missouri dot edu )
advertisement register. Some PHYs such as 88E3016 requires NEXT
Page capability to establish valid link. Also set protocol selector
field which is read only but it makes the intention clearer.
is valid only for auto-negotiation case so check the bit if we know
auto-negotiation is active. While I'm here explicitly checks
current speed with speed mask and set IFM_NONE if resolved speed
is unknown.
checks extended status register to see whether the PHY is fast
ethernet or not. This removes a lot of checks for specific PHY
models and it makes easy to add more PHYs to e1000phy(4).
While I'm here remove setting mii_anegticks as it is set with
mii_phy_add_media().
Remove PAGE_SIZE alignment used in Rx buffer DMA tag creation. The
alignment restriction was used in old local jumbo allocator and
nfe(4) switched to UMA backed page allocator for jumbo frame.
This change should fix jumbo buffer allocation failure.
Reported by: Pascal Braun ( pascal.braun <> continum dot net )
only if prepping the adapter failed.
Slight adjustment to comments.
Fix a bug whereby downing the interface didn't preven it from
processing packets.
Submitted by: Navdeep Parhar
MFC after: 1 week
Some hardware easily comes out of sync with regard to whether the current or
the next control transfer should be stalled, if a stall command is always
issued before receiving the SETUP packet. After this patch the stall command
will only be issued when a transfer should actually be stalled.
Submitted by: Hans Petter Selasky
1) Add a sysctl that will say what type of PHYs exist on the card.
2) Fix a bug that occurs when an AEL 2005 PHY resets without a transciever
in the card.
3) Unify the PHY link detection code.
Obtained from: Navdeep Parhar
MFC after: 10 days
and down more cleanly. This addresses a problem where if we have the
link flap during boot the driver would lock up the system.
Reviewed by: jhb
MFC after: 1 week
thread. Multiple RAID events in quick succession can cause an additional
bus rescan to be scheduled before an earlier scan has completed. In this
case the driver was attempting to use the same CCB storage for two requests.
PR: kern/130330
Reviewed by: Riccardo Torrini riccardo.torrini | esaote com
MFC after: 1 week
o Header file cleanup.
o bus_dma(9) conversion.
- Removed all consumers of vtophys(9) and converted to use
bus_dma(9).
- 64bit DMA support was disabled because DP83821 is not capable
of handling the DMA request. 64bit DMA request on DP83820
requires different descriptor structures and it's hard to
dynamically change descriptor format at run time so I disabled
it. Note, this is the same behavior as previous one but
previously nge(4) didn't explicitly disable 64bit mode on
DP83820.
- Added Tx/Rx descriptor ring alignment requirements(8 bytes
alignment).
- Limit maximum number of Tx DMA segments to 16. In fact,
controller does not seem to have limitations on number of Tx
DMA segments but 16 should be enough for most cases and
m_collapse(9) will handle highly fragmented frames without
consuming a lot of CPU cycles.
- Added Rx buffer alignment requirements(8 bytes alignment). This
means driver should fixup received frames to align on 16bits
boundary on strict-alignment architectures.
- Nuked driver private data structure in descriptor ring.
- Added endianness support code in Tx/Rx descriptor access.
o Prefer faster memory mapped register access to I/O mapped access.
Added fall-back mechanism to use alternative register access.
The hardware supports both memory and I/O mapped access.
o Added suspend/resume methods but it wasn't tested as controller I
have does not support PCI PME.
o Removed swap argument in nge_read_eeprom() since endianness
should be handled after reading EEPROM.
o Implemented experimental 802.3x full-duplex flow-control. ATM
it was commented out but will be activated after we have generic
flow-control framework in mii(4) layer.
o Rearranged promiscuous mode settings and simplified logic.
o Always disable Rx filter prior to changing Rx filter functions as
indicated in DP83820/DP83821 datasheet.
o Added an explicit DELAY in timeout loop of nge_reset().
o Added a sysctl variable dev.nge.%d.int_holdoff to control
interrupt moderation. Valid ranges are 1 to 255(default 1) in
units of 100us. The actual delivery of interrupt would be delayed
based on the sysctl value. The interface has to be brought down
and up again before a change takes effect. With proper tuning
value, users do not need to resort to polling(4) anymore.
o Added ALTQ(4) support.
o Added missing IFCAP_VLAN_HWCSUM as nge(4) can offload Tx/Rx
checksum calculation on VLAN tagged frames as well as VLAN tag
insertion/stripping. Also add IFCAP_VLAN_MTU capability as nge(4)
can handle VLAN tagged oversized frames.
o Fixed media header length for VLAN.
o Rearranged nge_detach routine such that it's now used for general
clean-up routine.
o Enabled MWI.
o Accessing EEPROM takes very long time so read 6 bytes ethernet
address with one call instead of 3 separate accesses.
o Don't set if_mtu in device attach, it's already set in
ether_ifattach().
o Don't do any special things for TBI interface. Remove TBI
specific media handling in the driver and have gentbi(4) handle
it. Add glue code to read/write TBI PHY registers in miibus
method. This change removes a lot of PHY handling code in driver
and now its functionality is handled by mii(4).
o Alignment fixup code is now applied only for strict-alignment
architectures. Previously the code was applied for all
architectures except i386. With this change amd64 will get
instant Rx performance boost.
o When driver fails to allocate a new mbuf, update if_qdrops so
users can see what was wrong in Rx path.
o Added a workaround for a hardware bug which resulted in short
VLAN tagged frames(e.g. ARP) was rejected as if runt frame was
received. With this workaround nge(4) now accepts the short VLAN
tagged frame and nge(4) can take full advantage of hardware VLAN
tag stripping. I have no idea how this bug wasn't known so far,
without the workaround nge(4) may never work on VLAN
environments.
o Fixed Rx checksum offload logic such that it now honors active
interface capability configured with ifconfig(8).
o In nge_start()/nge_txencap(), always leave at least one free
descriptor as indicated in datasheet. Without this the hardware
would be confused with ring descriptor structure(e.g. no clue
for the end of descriptor ring).
o Removed dead-code that checks interrupts on PHY hardware. The
code was designed to detect link state changes but it was
disabled as driving nge_tick clock would break auto-negotiation
timer. This code is no longer needed as nge(4) now uses mii(4)
and link state change handling is done with mii callback.
o Rearranged ethernet address programming logic such that it works
on strict-alignment architectures.
o Added IFCAP_VLAN_HWTAGGING/IFCAP_VLAN_HWCSUM handler in
nge_ioctl() such that the functionality is configurable with
ifconfig(8). DP83820/DP83821 can do checksum offload for VLAN
tagged frames so enable Tx/Rx checksum offload for VLAN
interfaces.
o Simplified IFCAP_POLLING selection logic in nge_ioctl().
o Fixed module unload panic when bpf listeners are active.
o Tx/Rx descriptor ring address uses 64bit DMA address for
readability. High address part of DMA would be 0 as nge(4)
disabled 64bit DMA transfers so it's ok for DP83821.
o Removed volatile keyword in softc as bus_dmamap_sync(9) should
take care of this.
o Removed extra driver private structures in descriptor ring. These
extra elements are not part of descriptor structure. Embedding
private driver structure into descriptor ring is not good idea
as its size may be different on 32bit/64bit architectures.
o Added miibus_linkchg method handler to catch link state changes.
o Removed unneeded nge_ifmedia in softc. All TBI access is handled
in gentbi(4). There is no difference between TBI and non-TBI case
now.
o Removed "gigabit link up" message handling in nge_tick. Link
state change notification is already performed by mii(4) and
checking link state by accessing PHY registers in periodic timer
handler of driver is wrong. All link state and speed/duplex
monitoring should be handled in PHY driver.
o Use our own timer for watchdog instead of if_watchdog/if_timer
interface.
o Added hardware MAC statistics counter, users canget current MAC
statistics from dev.nge.%d.stats sysctl node(%d is unit number of
a device).
o Removed unused macros, NGE_LASTDESC, NGE_MODE, NGE_OWNDESC,
NGE_RXBYTES.
o Increased number of Tx/Rx descriptors from 128 to 256. From my
experience on gigabit ethernet controllers, number of descriptors
should be 256 or higher to get an optimal performance on gigabit
link.
o Increased jumbo frame length to 9022 bytes to cope with other
gigabit ethernet drivers. Experimentation shows no problems with
9022 bytes.
o Removed unused member variables in softc.
o Switched from bus_space_{read|write}_4 to bus_{read|write}_4.
o Added support for WOL.
o replace DLT_IEEE802_11 support in net80211 with DLT_IEEE802_11_RADIO
and remove explicit bpf support from wireless drivers; drivers now
use ieee80211_radiotap_attach to setup shared data structures that
hold the radiotap header for each packet tx/rx
o remove rx timestamp from the rx path; it was used only by the tdma support
for debugging and was mostly useless due to it being 32-bits and mostly
unavailable
o track DLT_IEEE80211_RADIO bpf attachments and maintain per-vap and
per-com state when there are active taps
o track the number of monitor mode vaps
o use bpf tap and monitor mode vap state to decide when to collect radiotap
state and dispatch frames; drivers no longer explicitly directly check
bpf state or use bpf calls to tap frames
o handle radiotap state updates on channel change in net80211; drivers
should not do this (unless they bypass net80211 which is almost always
a mistake)
o update various drivers to be more consistent/correct in handling radiotap
o update ral to include TSF in radiotap'd frames
o add promisc mode callback to wi
Reviewed by: cbzimmer, rpaulo, thompsa
bug referencing a destroyed lock within TX callbacks during device
detach.
Submitted by: hps (original version)
Tested by: Lucius Windschuh <lwindschuh at googlemail.com>
possible future I-cache coherency operation can succeed. On ARM
for example the L1 cache can be (is) virtually mapped, which
means that any I/O that uses temporary mappings will not see the
I-cache made coherent. On ia64 a similar behaviour has been
observed. By flushing the D-cache, execution of binaries backed
by md(4) and/or NFS work reliably.
For Book-E (powerpc), execution over NFS exhibits SIGILL once in
a while as well, though cpu_flush_dcache() hasn't been implemented
yet.
Doing an explicit D-cache flush as part of the non-DMA based I/O
read operation eliminates the need to do it as part of the
I-cache coherency operation itself and as such avoids pessimizing
the DMA-based I/O read operations for which D-cache are already
flushed/invalidated. It also allows future optimizations whereby
the bcopy() followed by the D-cache flush can be integrated in a
single operation, which could be implemented using on-chips DMA
engines, by-passing the D-cache altogether.
register 0x52, not ctrl1. This appears to be a mistake in the bcm
reverse engineering page, and has been corrected there. Tracing
through the code, this is more in keeping with the "documented"
register. Sephe thinks it looks interesting and may be worth
fixing. :)
Submitted by: ddkprog at yahoo com
Reviewed by: Sepherosa Ziehau
- In bce_rx_intr(), use BUS_DMASYNC_POSTREAD instead of
BUS_DMASYNC_POSTWRITE, as we want to "read" from the
rx page chain pages.
- Document why we need to do PREWRITE after we have updated
the rx page chain pages.
- In bce_intr(), use BUS_DMASYNC_POSTREAD and
BUS_DMASYNC_PREREAD when before and after CPU "reading"
the status block.
- Adjust some nearby style mismatches/etc.
Pointed out by: yongari
Approved by: davidch (no objection) but bugs are mine :)
# Note: The driver doesn't support either these PHY types, so this is
# effectively a nop.
Submitted by: "ddk"
Obtained from: http://paradox.lissyara.su/bwi.diff
believe it was a BCM4319. However, it is the a/b/g variation of the
BCM4318. The chip itself is labelled BCM4318EKFBG, and the board is
BCM94318MKABG.
Paradox's patch includes the type of 802.11 wireless for each card,
but changes all the names (I don't think the latter is quite right).
Import that part of the patch, but keep the current set of BCM names
(with a minor tweak for the 4306 ones). I'll need to verify them via
some other means.
Obtained from: http://paradox.lissyara.su/bwi.diff (partially)
Apart from the 16 virtual terminals, Syscons allocates two device nodes
that should not really be TTYs, even though they are. One of them is
consolectl. In RELENG_7 and before, these device nodes are used in
single user mode. After I simplified input path, we only use this device
node to call ioctl() on (moused, Xorg, vidcontrol).
When you call ioctl() on consolectl, it will behave the same as being
called on the first window.
drops and re-grabs the softc mutex in the middle, resulting in kernel
trap 12. This may happen when a lot of traffic is being hammered on
one bge(4) interface while the system is shutting down.
Reported by: Alexander Sack <pisymbol gmail com>
PR: kern/134548
MFC After: 2 weeks
chipset-specific code to attach chipset-specific data.
- Use chipset-specific data in the acard and promise chipsets rather than
changing the ivars of ATA PCI devices. ivars are reserved for use by the
parent bus driver and are _not_ available for use by devices directly.
This fixes a panic during sysctl -a with certain Promise controllers with
ACPI enabled.
Reviewed by: mav
Tested by: Magnus Kling (kingfon @ gmail) (on 7)
MFC after: 3 days
NULL or change it. We initialize it before we set if_ioctl. It can
therefore never be NULL, and most other drivers don't bother with this
sanity check.
As an experiment, I changed snp(4) to use a mutex instead of an sx lock.
We can't enable this right now, because Syscons still picks up Giant.
It's nice to already have the framework there.
adapted to MPSAFE cam(4) to a isp(4) specific callout structure.
Thanks to Florian Smeets for providing access to a machine exhibiting
this problem for debugging.
Approved by: mjacob
MFC after: 3 days
sc_rixmap is an inverse map
NB: could eliminate the check for an invalid rate by filling in 0 for
invalid entries but the rate control modules use it to identify
bogus rates so leave it for now
previously always pointing to the default vnet context, to a
dynamically changing thread-local one. The currvnet context
should be set on entry to networking code via CURVNET_SET() macros,
and reverted to previous state via CURVNET_RESTORE(). Recursions
on curvnet are permitted, though strongly discuouraged.
This change should have no functional impact on nooptions VIMAGE
kernel builds, where CURVNET_* macros expand to whitespace.
The curthread->td_vnet (aka curvnet) variable's purpose is to be an
indicator of the vnet context in which the current network-related
operation takes place, in case we cannot deduce the current vnet
context from any other source, such as by looking at mbuf's
m->m_pkthdr.rcvif->if_vnet, sockets's so->so_vnet etc. Moreover, so
far curvnet has turned out to be an invaluable consistency checking
aid: it helps to catch cases when sockets, ifnets or any other
vnet-aware structures may have leaked from one vnet to another.
The exact placement of the CURVNET_SET() / CURVNET_RESTORE() macros
was a result of an empirical iterative process, whith an aim to
reduce recursions on CURVNET_SET() to a minimum, while still reducing
the scope of CURVNET_SET() to networking only operations - the
alternative would be calling CURVNET_SET() on each system call entry.
In general, curvnet has to be set in three typicall cases: when
processing socket-related requests from userspace or from within the
kernel; when processing inbound traffic flowing from device drivers
to upper layers of the networking stack, and when executing
timer-driven networking functions.
This change also introduces a DDB subcommand to show the list of all
vnet instances.
Approved by: julian (mentor)
Broadcom BCM43xx chipsets. This driver uses the v3 firmware that
needs to be fetched separately. A port will be committed to create
the bwi firmware module.
The driver matches the following chips: Broadcom BCM4301, BCM4307,
BCM4306, BCM4309, BCM4311, BCM4312, BCM4318, BCM4319
The driver works for 802.11b and 802.11g.
Limitations:
This doesn't support the 802.11a or 802.11n portion of radios.
Some BCM4306 and BCM4309 cards don't work with Channel 1, 2 or 3.
Documenation for this firmware is reverse engineered from
http://bcm.sipsolutions.net/
V4 of the firmware is needed for 11a or 11n support
http://bcm-v4.sipsolutions.net/
Firmware needs to be fetched from a third party, port to be committed
# I've tested this with a BCM4319 mini-pci and a BCM4318 CardBus card, and
# not connected it to the build until the firmware port is committed.
Obtained from: DragonFlyBSD, //depot/projects/vap
Reviewed by: sam@, thompsa@
leading to a bug, when C-state does not decrease on sleep shorter then
declared transition latency. Fixing this deprecates workaround for broken
C-states on some hardware.
By the way, change state selecting logic a bit. Instead of last sleep
time use short-time average of it. Global interrupts rate in system is a
quite random value, to corellate subsequent sleeps so directly.
sleepable context for net80211 driver callbacks. This removes the need for USB
and firmware based drivers to roll their own code to defer the chip programming
for state changes, scan requests, channel changes and mcast/promisc updates.
When a driver callback completes the hardware state is now guaranteed to have
been updated and is in sync with net80211 layer.
This nukes around 1300 lines of code from the wireless device drivers making
them more readable and less race prone.
The net80211 layer has been updated as follows
- all state/channel changes are serialised on the taskqueue.
- ieee80211_new_state() always queues and can now be called from any context
- scanning runs from a single taskq function and executes to completion. driver
callbacks are synchronous so the channel, phy mode and rx filters are
guaranteed to be set in hardware before probe request frames are
transmitted.
Help and contributions from Sam Leffler.
Reviewed by: sam
- Generate fake channel interrupts even if channel busy with previous
request to let it finish. Without this, dumping requests were just queued
and never processed.
- Drop pre-dump requests queue on dumping. ATA code, working in dumping
(interruptless) mode, unable to handle long request queue. Actually, to get
coherent dump we anyway should do as few unrelated actions as possible.
Yukon from common multicast handling code. Yukon uses hash-based
multicast filtering(big endian form) but GENESIS uses perfect
multicast filtering as well as hash-based one(little endian form).
Due to the differences of multicast filtering there is no much
sense to have a common code.
o Remove sk_setmulti() and introduce sk_rxfilter_yukon(),
sk_rxfilter_yukon() that handles multicast filtering setup.
o Have sk_rxfilter_{yukon, genesis} handle promiscuous mode and
nuke sk_setpromisc(). This simplifies ioctl handler as well as
giving a chance to check validity of Rx control register of
Yukon.
o Don't reinitialize controller when IFF_ALLMULTI flags is changed.
o Nuke sk_gmchash(), it's not needed anymore.
o Always reconfigure Rx control register whenever a new multicast
filtering condition is changed. This fixes multicast filtering
setup on Yukon.
PR: kern/134051
- Probe supported sleep states from acpi_attach() just once and do not
call AcpiGetSleepTypeData() again. It is redundant because
AcpiEnterSleepStatePrep() does it any way.
- Treat UNKNOWN sleep state as NONE, i.e., "do nothing", and remove obscure
NONE state (ACPI_S_STATES_MAX + 1) to avoid confusions.
- Do not set unsupported sleep states as default button/switch events.
If the default sleep state is not supported, just set it as UNKNOWN/NONE.
- Do not allow sleep state change if the system is not fully up and running.
This should prevent entering S5 state multiple times, which causes strange
behaviours later.
- Make sleep states case-insensitive when they are used with sysctl(8).
For example,
sysctl hw.acpi.lid_switch_state=s1
sysctl hw.acpi.sleep_button_state=none
are now legal and equivalent to the uppercase ones.
Feature is controlled by hint.ata.X.pm_level tunable:
0 - PM disabled, old behaviour, default.
1 - device is allowed to initiate PM state change, host is passive.
2 - host initiates PARTIAL state transition every time port is idle.
3 - host initiates SLUMBER state transition every time port is idle.
PARTIAL state has up to 100us (50us for me) wakeup latency, but for my
ICH8M saves 0.5W of power per drive. SLUMBER state has up to 10ms (3.5ms
for me) wakeup latency, but saves 0.8W of power.
Modes 2 and 3 are implemented only for AHCI driver now.
Interface power management is incompatible with device presence detection
(host receives no signal from drive, so unable to monitor it), so later is
disabled when PM is used.
- Add some missing const.
- Move the size of the window spun by the registers to the softc
as neither using va_mem_size for this nor va_mem_base for the
start of the bus addresses is appropriate.
MFC after: 1 week
This change adds (possibly redundant) early check for invalid
state input parameter (including S0). Handling of S5 request
is reduced to simply calling shutdown_nice(). As a result
control flow of acpi_EnterSleepState is somewhat simplified
and resume/backout half of the function is not executed
for S5 (soft poweroff) request and invalid state requests.
Note: it seems that shutdown_nice may act as nop when initproc
is already initialized (to grab pid of 1), but init process is in
"pre-natal" state.
Tested by: Fabian Keil <fk@fabiankeil.de>
Reviewed by: njl, jkim
Approved by: rpaulo
controllers may be configured as legacy IDE mode by modifying subclass and
progif without actually changing PCI device IDs. Instead of complicating
code, we always force AHCI mode while probing. Also we restore AHCI mode
while resuming per ATI/AMD register programming/requirement guides.
- Fix SB700/800 "combined" mode. Unlike SB600, this PATA controller can
combine two SATA ports and emulate one PATA channel as primary or secondary
depending on BIOS configuration. When the combined mode is disabled, this
channel disappears and it works just like SB600 PATA controller, however.
- Add more PCI device IDs for SB700/800 and adjust device descriptions.
SB800 shares the same PCI device IDs and added two more SATA IDs.
this driver to compile and limp along with the new layer. These changes
do not deal with proper locking around access to the HW. This is only
a starting point. I have not tested modem control but tip seems to work
okay and I can send and receive characters which I needed for one of my
-current boxes. I have not tied this driver back up to the build since
I don't want people to think it is ready for prime time. If anyone
else has some cycles to work on this feel free to!
Also add support for a 16 port PCI interface I have at work.
Glanced at by: ed
- Update mxge to use if_transmit(), and the new buf_ring
interfaces, so as to enable multiple transmit queues.
Use of if_transmit() is conditional on IFNET_BUF_RING,
and is enabled by default (as in if_em).
- Record a flow id on receive if receive hashing is active.
I currently only record the rx ring id (0..8) rather than
the 32-bit topelitz hash result, as doing the latter would
require shifting the driver to use a larger rx return ring.
Sponsored by: Myricom, Inc.
(1) Don't manually configure if_output(), ether_ifattach() will do that
for us as part of link-layer setup.
(2) Call if_detach() before stopping nve in order to prevent calls into
the device driver after the driver has started shutting down.
Reviewed by: jhb
MFC after: 2 weeks
Change the roothub exec functions to take the usb request and data pointers
directly rather than placing them on the parent bus struct.
Submitted by: Hans Petter Selasky
Fix a bug in the USB power daemon code where connection of multiple HUBs in
series would result in incorrect device suspend.
Reported by: Nicolas xxx@wanadoo.fr
Submitted by: Hans Petter Selasky
Use direct reference to parent high-speed HUB instead of indirect, due to
pointer clearing race at detach of parent USB HUB.
Reported by: kientzle
Submitted by: Hans Petter Selasky
PR: usb/133545
respectivly. This will allow one to have a kernel with both devices
present and use it for multiple boards with different types of RTC
sitting on a bus.
Discussed with: imp
number of queued packets in watchdog timeout handler. If there are
no queued packets just print a informational message and return
without resetting controller. Also fix to invoke correct Tx
completion handler as 3C905B needs different handler.
Previously it used to clear the flag only when the transmit queue
is empty which may slow down Tx performance.
While I'm here check whether driver is running and whether we can
queue more packets in if_start handler. This fixes occasional
watchdog timeouts.
Reported by: xer < xernet <> hotmail dot it >
Tested by: xer < xernet <> hotmail dot it >
