just because you leave your session idle.
Also, put in a fix for 64-bit architectures (to be revised).
In detail:
ip_fw.h
* Reorder fields in struct ip_fw to avoid alignment problems on
64-bit machines. This only masks the problem, I am still not
sure whether I am doing something wrong in the code or there
is a problem elsewhere (e.g. different aligmnent of structures
between userland and kernel because of pragmas etc.)
* added fields in dyn_rule to store ack numbers, so we can
generate keepalives when the dynamic rule is about to expire
ip_fw2.c
* use a local function, send_pkt(), to generate TCP RST for Reset rules;
* save about 250 bytes by cleaning up the various snprintf()
in ipfw_log() ...
* ... and use twice as many bytes to implement keepalives
(this seems to be working, but i have not tested it extensively).
Keepalives are generated once every 5 seconds for the last 20 seconds
of the lifetime of a dynamic rule for an established TCP flow. The
packets are sent to both sides, so if at least one of the endpoints
is responding, the timeout is refreshed and the rule will not expire.
You can disable this feature with
sysctl net.inet.ip.fw.dyn_keepalive=0
(the default is 1, to have them enabled).
MFC after: 1 day
(just kidding... I will supply an updated version of ipfw2 for
RELENG_4 tomorrow).
- As before, inetd support support is turned of per default.
Code for inetd can be made with -I.
- Support for ``transport monitors'' and the NLSPROVIDER env
variable is still there , even if their use is not clear in
non TLI stream based systems like Free-/NetBSD. It can be activated
with -P.
- There are a few corrections in rpcgen.1 and usage function to conform
to the code. Added and documented -P
- I removed the #ifdefs checks for Free-/NetBSD since we are the only
ones who use this code. MaxOS X may have the same limitations as
we have, so this code will correctly build for them.
- Generate correct cflags.
Submitted by: mbr, Jean-Luc Richier <Jean-Luc.Richier@imag.fr>
PR: bin/29175, misc/27816
- always reinitialize the rx descriptors, even if the mbuf is kept.
This should fix the hangs on ifconfig that were observed
- on an rx overflow, reinitialize the descriptor so that the interface
will not hang
- correct some bus_dmamap_sync() calls
- correct some debug messages
- some minor nits
Following a suggestion by Ruslan, the initial creation of the
includes and libraries (and build tools) is now done by
invoking "make buildworld" (with -DPICOBSD which eventually will
limit the amount of stuff built with a 2-line change in Makefile.inc1).
The correct environment is then used for subsequent builds.
Also remove write_mfs_in_kernel.c in favour of using dd
All the above is conditional on __FreeBSD_version, as the previous
method still worked for versions earlier than 500035, and I am
unsure on how the "new" method works for earlier versions.
Finally, note that the crunch.conf files need some work because
some libraries (e.g. gmd) have gone away from the base installation.
1/ don't need to set td_state to TDS_RUNNING in fork_return.
it's already set in choosethread().
2/ Set a child process state to "normal" as opposed to "new"
when we allow it to be put on the run queue.
Allows child to receive signals from the parent if the parent
runs first and tries to immediatly signal he child.
Submitted by: (part 2) Thomas Moestl <tmoestl@gmx.net>
that's binary compatible for -stable. While binary compatibility doesn't
matter much in -current, it is critical for -stable. This change requires
pccardd/pccardc to be recompiled.
formulated. The correct states should be:
IDLE: On the idle KSE list for that KSEG
RUNQ: Linked onto the system run queue.
THREAD: Attached to a thread and slaved to whatever state the thread is in.
This means that most places where we were adjusting kse state can go away
as it is just moving around because the thread is..
The only places we need to adjust the KSE state is in transition to and from
the idle and run queues.
Reviewed by: jhb@freebsd.org