The priority goes from "error" to "debug".
Connectors are polled every 10 seconds. Reading EDID is part of this
polling. However, when an invalid EDID is returned, this error message
is logged. When using Newcons for instance, having a kernel message
every 10 seconds is getting annoying.
Now that it's a debug message, it'll be logged only if hw.dri.debug is
enabled. This fix console spamming for some users.
Tested by: Larry Rosenman <ler@lerctr.org>
location of /etc/rc.local on the install media is more appropriate as it
knows serial vs. non-serial and can also do the change earlier (so that
even the initial Install dialog can benefit from the change).
MFC after: 3 days
clients. Mask RX interrupts while grabbed on the atmel serial
driver. This UART interrupts every character. When interrupts are
enabled at the mountroot> prompt, this means the ISR eats the
characters. Rather than try to create a cooperative buffering system
for the low level kernel console, instead just mask out the ISR. For
NS8250 and decsendents this isn't needed, since interrupts only happen
after 14 or more characters (depending on the fifo settings). Plumb
such that these are optional so there's no change in behavior for all
the other UART clients. ddb worked on this platform because all
interrupts were disabled while it was running, so this problem wasn't
noticed. The mountroot> issue has been around for a very very long
time.
MFC after: 3 days
... for msleep/cv_*wait() return values, where wait_event*() is used
on Linux. ERESTARTSYS is the return code expected by callers when the
operation was interrupted.
For instance, this is the case of radeon_cs_ioctl() (radeon_cs.c): if
an error occurs, and the code isn't ERESTARTSYS (eg. EINTR), it logs an
error.
Note that ERESTARTSYS is defined as ERESTART, but this keeps callers'
code close to Linux.
Submitted by: avg@ (previous version)
to the soreceive(). This exposed a bug. When reading from a raw socket,
when our fake limit is depleted, we receive a truncated mbuf chain, with
m->m_pkthdr.len > m_length(m). The first problem is that MSG_TRUNC was not
handled. The second one is that we didn't reinit uio_resid in our endless
loop (neither flags), and if socket buffer contained several records, then
we quickly deplete our fake limit. The third bug, actually introduced in
r248885, is that MJUMPAGESIZE isn't enough to handle maximum packet that
ng_ksocket(4) can theoretically receive.
Changes:
- Reinit uio_resid and flags before every call to soreceive().
- Set maximum acceptable size of packet to IP_MAXPACKET. As for now the
module doesn't support INET6.
- Properly handle MSG_TRUNC return from soreceive().
PR: 184601
Submitted & tested by: Viktor Velichkin <avisom yandex.ru>
Sponsored by: Nginx, Inc.
Normal and bold fonts each have a glyph map for single or left half-
glyphs, and right half glyphs. The flag TF_CJK_RIGHT in term_char_t
requests the right half-glyph.
Reviewed by: ed@
Sponsored by: The FreeBSD Foundation
The previous code was checking the "VGA Enable" bit on the video card's
parent PCI-to-PCI bridge only. This didn't work for the case where the
video card is attached to the root PCI bus (ie. the card has no parent
PCI-to-PCI bridge).
Now, the new code:
1. checks the "VGA Enable" bit on the parent bridge only if it's a
PCI-to-PCI bridge;
2. always checks the "I/O" and "Memory address space decoding" bits
on the video card itself.
However, vendor-specific bits are not used.
This fixes the use of many integrated Radeon cards: without this patch,
we fail to detect them as the boot display and, when radeonkms looks for
the Video BIOS, it skips the shadow copy made by the System BIOS. It
then fails to fully initialize the card, because the shadow copy is the
only way to read the Video BIOS in these situations. A workaround was to
force the boot display selection using the "hw.pci.default_vgapci_unit"
tunable.
A previous version of this patch added a new function doing the checks.
Now, the vga_pci_is_boot_display() function is used to perform the
checks (only until the boot display is found) and return if the given
device is the boot display or not.
Furthermore, vga_pci_attach() logs "Boot video device" if the card being
attached it the Chosen One:
vgapci0: <VGA-compatible display> [...]
vgapci0: Boot video device
Reviewed by: kib@, jhb@ (both a previous version)
Tested by: lunatic_ (#freebsd-xorg, integrated Radeon card,
xmj (#freebsd-xorg, i915+NVIDIA cards)
This, and several subsequent commits, are suspend/resume for various PowerMac
drivers, which will include a change to the global suspend/resume code
eventually.
Introduce a new formatting bit (TF_CJK_RIGHT) that is set when putting a
cell that is the right part of a CJK fullwidth character. This will
allow drivers like vt(9) to support fullwidth characters properly.
emaste@ has a patch to extend vt(9)'s font handling to increase the
number of Unicode -> glyph maps from 2 ({normal,bold)} to 4
({normal,bold} x {left,right}). This will need to use this formatting
bit to determine whether to draw the left or right glyph.
Reviewed by: emaste
Fixes GCC libstdc++/29286
The fix seems to work for amd64 but causes segfaults on powerpc.
At this time gcc is much more important on powerpc than on amd64.
Reported by: andreast
They are very useful but at this time I prefer not to figure out
some minor conflicts with the bigger Apple's blocks support
patch that is being worked on for current.
Do not insert active ports into pool->sp_active list if they are success-
fully assigned to some thread. This makes that list include only ports that
really require attention, and so traversal can be reduced to simple taking
the first one.
Remove idle thread from pool->sp_idlethreads list when assigning some
work (port of requests) to it. That again makes possible to replace list
traversals with simple taking the first element.
With this, also shut shut off the display (DPMS-style) and disable the clocking
when the backlight level is set to 0. This is taken from the radeonkms driver
(radeon_legacy_encoders.c) which doesn't yet support PowerPC, and won't for a
while, as it's missing full AGP support.
