Before that fix, it was possible for the function to fail if number
of sharers changes between 'x = sx->sx_lock' step and atomic_cmpset_acq_ptr()
call.
This fixes ZFS problem when ZFS returns strange EIO errors under load.
In ZFS there is a code that depends on the fact that sx_try_slock() can
only fail if there is an exclusive owner.
Discussed with: attilio
Reviewed by: jhb
Approved by: re (kensmith)
after the switch leads to a race where the outgoing thread still owns
the local queue lock while another cpu may switch it in. This race
is only possible on machines where cpu_switch can take significantly
longer on different cpus which in practice means HTT machines with
unfair thread scheduling algorithms.
Found by: kris (of course)
Approved by: re
starvation caused by unbalanced interrupt loads.
- Change the rebalancer to work on stathz ticks but retain randomization.
- Simplify locking in tdq_idled() to use the tdq_lock_pair() rather than
complex sequences of locks to avoid deadlock.
Reported by: kris
Approved by: re
the threading libraries is built. This simplifies the
logic in makefiles that need to check if the pthreads
support is present. It also fixes a bug where we would
build a threading library that we shouldn't have built:
for example, building with WITHOUT_LIBTHR and the default
value of DEFAULT_THREADING_LIB (libthr) would mistakenly
build the libthr library, but not install it.
Approved by: re (kensmith)
the threading libraries is built. This simplifies the
logic in makefiles that need to check if the pthreads
support is present. It also fixes a bug where we would
build a threading library that we shouldn't have built:
for example, building with WITHOUT_LIBTHR and the default
value of DEFAULT_THREADING_LIB (libthr) would mistakenly
build the libthr library, but not install it.
Approved by: re (kensmith)
retransmittion by handover event (fast mobility code)
- Fixed problem of mobility code which is caused by remaining
parameters in the deleted primary destination.
- Add a missing lock. When a peer sends an INIT, and while we
are processing it to send an INIT-ACK the socket is closed,
we did not hold a lock to keep the socket from going away.
Add protection for this case.
- Fix so that arwnd is alway uses the minimal rwnd if the user
has set the socket buffer smaller. Found this when the test
org decided to see what happens when you set in a rwnd of 10
bytes (which is not allowed per RFC .. 4k is minimum).
- Fixes so a cookie-echo ootb will NOT cause an abort to
be sent. This was happening in a MPI collision case.
- Examined all panics and unless there was no recovery, moved
any that were not already to INVARANTS.
Approved by: re@freebsd.org (gnn)
support machines having multiple independently numbered PCI domains
and don't support reenumeration without ambiguity amongst the
devices as seen by the OS and represented by PCI location strings.
This includes introducing a function pci_find_dbsf(9) which works
like pci_find_bsf(9) but additionally takes a domain number argument
and limiting pci_find_bsf(9) to only search devices in domain 0 (the
only domain in single-domain systems). Bge(4) and ofw_pcibus(4) are
changed to use pci_find_dbsf(9) instead of pci_find_bsf(9) in order
to no longer report false positives when searching for siblings and
dupe devices in the same domain respectively.
Along with this change the sole host-PCI bridge driver converted to
actually make use of PCI domain support is uninorth(4), the others
continue to use domain 0 only for now and need to be converted as
appropriate later on.
Note that this means that the format of the location strings as used
by pciconf(8) has been changed and that consumers of <sys/pciio.h>
potentially need to be recompiled.
Suggested by: jhb
Reviewed by: grehan, jhb, marcel
Approved by: re (kensmith), jhb (PCI maintainer hat)
After discussion with Sam, switch back to use firmware(9) instead of
having the firmware in hex format.
Put the binary firmware uuencoded into sys/contrib/dev/npe, and slap a
LICENSE file, as found on the Intel website.
Approved by: re (blanket), mux (mentor)
MFC After: 1 week
Without this change the following situation was possible:
1. Provider is orphaned from within class' access() method on last write
close - orphan provider event is send.
2. GEOM detects last write close on a provider and sends new provider event.
3. g_orphan_register() is called, and calls all orphan methods of attached
consumers.
4. New provider event is executed on orphaned provider, all classes can
taste already orphaned provider, and some may attach consumers to it.
Those consumers will never go away, because the g_orphan_register()
was already called.
We end up with a zombie provider.
With this change, at step 3, we will cancel new provider event.
How to repeat this problem:
# mdconfig -a -t malloc -s 10m
# geli init -i 0 md0
# geli attach md0
# newfs -L test /dev/md0.eli
# mount /dev/ufs/test /mnt/tmp
# geli detach -l md0.eli
# umount /mnt/tmp
# glabel status
Name Status Components
ufs/test N/A N/A
Reviewed by: phk
Approved by: re (kensmith)
value for kern.sched.preempt_thresh appropriately. It can still by
adjusted at runtime. ULE will still use IPI_PREEMPT in certain
migration situations.
- Assert that we're not trying to compile ULE on an unsupported
architecture. To date, I believe only i386 and amd64 have implemented
the third cpu switch argument required.
Approved by: re
cache: vm_object_page_remove() should convert any cached pages that
fall with the specified range to free pages. Otherwise, there could
be a problem if a file is first truncated and then regrown.
Specifically, some old data from prior to the truncation might reappear.
Generalize vm_page_cache_free() to support the conversion of either a
subset or the entirety of an object's cached pages.
Reported by: tegge
Reviewed by: tegge
Approved by: re (kensmith)
to gem_attach() as the former access softc members not yet initialized
at that time and gem_reset() actually is enough to stop the chip. [1]
o Revise the use of gem_bitwait(); add bus_barrier() calls before calling
gem_bitwait() to ensure the respective bit has been written before we
starting polling on it and poll for the right bits to change, f.e. even
though we only reset RX we have to actually wait for both GEM_RESET_RX
and GEM_RESET_TX to clear. Add some additional gem_bitwait() calls in
places we've been missing them according to the GEM documentation.
Along with this some excessive DELAYs, which probably only were added
because of bugs in gem_bitwait() and its use in the first place, as
well as as have of an gem_bitwait() reimplementation in gem_reset_tx()
were removed.
o Add gem_reset_rxdma() and use it to deal with GEM_MAC_RX_OVERFLOW errors
more gracefully as unlike gem_init_locked() it resets the RX DMA engine
only, causing no link loss and the FIFOs not to be cleared. Also use it
deal with GEM_INTR_RX_TAG_ERR errors, with previously were unhandled.
This was based on information obtained from the Linux GEM and OpenSolaris
ERI drivers.
o Turn on workarounds for silicon bugs in the Apple GMAC variants.
This was based on information obtained from the Darwin GMAC and Linux GEM
drivers.
o Turn on "infinite" (i.e. maximum 31 * 64 bytes in length) DMA bursts.
This greatly improves especially RX performance.
o Optimize the RX path, this consists of:
- kicking the receiver as soon as we've a spare descriptor in gem_rint()
again instead of just once after all the ready ones have been handled;
- kicking the receiver the right way, i.e. as outlined in the GEM
documentation in batches of 4 and by pointing it to the descriptor
after the last valid one;
- calling gem_rint() before gem_tint() in gem_intr() as gem_tint() may
take quite a while;
- doubling the size of the RX ring to 256 descriptors.
Overall the RX performance of a GEM in a 1GHz Sun Fire V210 was improved
from ~100Mbit/s to ~850Mbit/s.
o In gem_add_rxbuf() don't assign the newly allocated mbuf to rxs_mbuf
before calling bus_dmamap_load_mbuf_sg(), if bus_dmamap_load_mbuf_sg()
fails we'll free the newly allocated mbuf, unable to recycle the
previous one but a NULL pointer dereference instead.
o In gem_init_locked() honor the return value of gem_meminit().
o Simplify gem_ringsize() and dont' return garbage in the default case.
Based on OpenBSD.
o Don't turn on MAC control, MIF and PCS interrupts unless GEM_DEBUG is
defined as we don't need/use these interrupts for operation.
o In gem_start_locked() sync the DMA maps of the descriptor rings before
every kick of the transmitter and not just once after enqueuing all
packets as the NIC might instantly start transmitting after we kicked
it the first time.
o Keep state of the link state and use it to enable or disable the MAC
in gem_mii_statchg() accordingly as well as to return early from
gem_start_locked() in case the link is down. [3]
o Initialize the maximum frame size to a sane value.
o In gem_mii_statchg() enable carrier extension if appropriate.
o Increment if_ierrors in case of an GEM_MAC_RX_OVERFLOW error and in
gem_eint(). [3]
o Handle IFF_ALLMULTI correctly; don't set it if we've turned promiscuous
group mode on and don't clear the flag if we've disabled promiscuous
group mode (these were mostly NOPs though). [2]
o Let gem_eint() also report GEM_INTR_PERR errors.
o Move setting sc_variant from gem_pci_probe() to gem_pci_attach() as
device probe methods are not supposed to touch the softc.
o Collapse sc_inited and sc_pci into bits for sc_flags.
o Add CTASSERTs ensuring that GEM_NRXDESC and GEM_NTXDESC are set to
legal values.
o Correctly set up for 802.3x flow control, though #ifdef out the code
that actually enables it as this needs more testing and mainly a proper
framework to support it.
o Correct and add some conversions from hard-coded functions names to
__func__ which were borked or forgotten in if_gem.c rev. 1.42.
o Use PCIR_BAR instead of a homegrown macro.
o Replace sc_enaddr[6] with sc_enaddr[ETHER_ADDR_LEN].
o In gem_pci_attach() in case attaching fails release the resources in
the opposite order they were allocated.
o Make gem_reset() static to if_gem.c as it's not needed outside that
module.
o Remove the GEM_GIGABIT flag and the associated code; GEM_GIGABIT was
never set and the associated code was in the wrong place.
o Remove sc_mif_config; it was only used to cache the contents of the
respective register within gem_attach().
o Remove the #ifdef'ed out NetBSD/OpenBSD code for establishing a suspend
hook as it will never be used on FreeBSD.
o Also probe Apple Intrepid 2 GMAC and Apple Shasta GMAC, add support for
Apple K2 GMAC. Based on OpenBSD.
o Add support for Sun GBE/P cards, or in other words actually add support
for cards based on GEM to gem(4). This mainly consists of adding support
for the TBI of these chips. Along with this the PHY selection code was
rewritten to hardcode the PHY number for certain configurations as for
example the PHY of the on-board ERI of Blade 1000 shows up twice causing
no link as the second incarnation is isolated.
These changes were ported from OpenBSD with some additional improvements
and modulo some bugs.
o Add code to if_gem_pci.c allowing to read the MAC-address from the VPD on
systems without Open Firmware.
This is an improved version of my variant of the respective code in
if_hme_pci.c
o Now that gem(4) is MI enable it for all archs.
Pointed out by: yongari [1]
Suggested by: rwatson [2], yongari [3]
Tested on: i386 (GEM), powerpc (GMACs by marcel and yongari),
sparc64 (ERI and GEM)
Reviewed by: yongari
Approved by: re (kensmith)
33MHz for calculating the latency timer values for its children.
Inspired by NetBSD doing the same and Linux as well as OpenSolaris
using a similar approach.
While at it rename a variable and change its type to be more
appropriate fuer values of PCI properties so the variable can be
more easily reused.
- Initialize the cache line size register of PCI devices to a
legal value; the cache line size is limited to 64 bytes by the
Fireplane/Safari, JBus and UPA interconnection busses. Setting
it to an unsupported value caused bad performance at least with
GEM as it causes them to not do cache line bursts and to not
issue cache line commands on the PCI bus.
Approved by: re (kensmith)
MFC after: 1 week
bad code at -O2. Since this is likely caused by the low-level
optimizer, testing TARGET_ARCH rather than MACHINE_ARCH should
handle ia64 cross-compilation as well. With this work-around
in place, we can release using the current GCC and Binutils
code at the default optimization level on ia64.
Approved by: re (kensmith)
Pointy hat to: me and my absence of -Wall in my CFLAGS.
MFC will happen at the same time of the earlier commit.
Thanks to ru@ for spotting.
Approved by: re (Ken Smith), grog@ (mentor)
timeout occurring at exactly the same time. If this happens, the nfsiod
exits although there may be a queued async IO request for it.
Found by : Kris Kennaway
Approved by: re
