little further. This gets us further on the way to be able to build it
successfully with clang. Using in-tree gcc, this shrinks boot2.bin with
60 bytes, the in-tree clang shaves off 72 bytes, and ToT clang 84 bytes.
Submitted by: rdivacky
Reviewed by: imp
caused link re-negotiation whenever application joins or leaves a
multicast group. If driver is running, it would have established a
link so there is no need to start re-negotiation. The re-negotiation
broke established link which in turn stopped multicast application
working while re-negotiation is in progress.
PR: kern/154667
MFC after: 1 week
vm_map_insert(), the kmem_back() assumption about newly inserted
entry might be broken due to interference of two factors. In the low
memory condition, when vm_page_alloc() returns NULL, supplied map is
unlocked. If another thread performs kmem_malloc() meantime, and its
map entry is placed right next to our thread map entry in the map,
both entries wire count is still 0 and entries are coalesced due to
vm_map_simplify_entry().
Mark new entry with MAP_ENTRY_IN_TRANSITION to prevent coalesce.
Fix some style issues, tighten the assertions to account for
MAP_ENTRY_IN_TRANSITION state.
Reported and tested by: pho
Reviewed by: alc
- Allocate coherent DMA memory for the request/response queue area and
and the FC scratch area.
These changes allow isp(4) to work properly on sparc64 with usage of the
IOMMU streaming buffers enabled.
Approved by: mjacob
MFC after: 2 weeks
Catch a set vnet upon return to user space. This usually
means return paths with CURVNET_RESTORE() missing.
If VNET_DEBUG is turned on we can even tell the function
that did the CURVNET_SET() which is really helpful; else
we print "N/A".
Sponsored by: The FreeBSD Foundation
Sponsored by: CK Software GmbH
Reviewed by: jhb
MFC after: 11 days
While updating Tx stats, already freed node could be referred and cause
page fault. To avoid such panic, spool Tx stats in driver's softc. Then,
on every ratectl interval, grab node though ieee80211_iterate_nodes() and
update ratectl stats.
* Simplify some code in run_iter_func().
* Fix typo
* Use memset instead of bzero (hselasky @)
PR: kern/153938
Submitted by: PseudoCylon <moonlightakkiy@yahoo.ca>
Approved by: thompsa (mentor)
The algorithm is supposed to work as follows:
in order to prevent starvation, when a new client starts being served we
record the start time and reset the counter of bytes served.
We then switch to a new client after a certain amount of time or bytes,
even if the current one still has pending requests.
To avoid charging a new client the time of the first seek,
we start counting time when the first request is served.
Unfortunately a bug in the previous version of the code failed
to set the start time in certain cases, resulting in some processes
exceeding their timeslice.
The fix (in this patch) is trivial, though it took a while to find
out and replicate the bug.
Thanks to Tommaso Caprai for investigating and fixing the problem.
Submitted by: Tommaso Caprai
MFC after: 1 week
at the Univ-of-Del. Basically when a 1-to-1 socket did a
socket/bind/send(data)/close. If the timing was right
we would dereference a socket that is NULL.
MFC after: 1 month
object's size field. Previously, that field was always zero, even
when the object tn_reg.tn_aobj contained numerous pages.
Apply style fixes to tmpfs_reg_resize().
In collaboration with: kib
journal blocks, instead of hard coding 512 byte sector size. Journal need
to atomically write the block, that can only be guaranteed at the device
sector size, not larger. Attempt to write less then sector size results in
driver errors.
Note that this is the first structure in UFS that depends on the
sector size. Other elements are written in the units of fragments.
In collaboration with: pho
Reviewed by: jeff
Tested by: bz, pho
active I/O to several disks (copying large file on ZFS) causes timeout after
just a few seconds of run. Single port 88SX6111 seems like not affected.
Skip reading transferred bytes count for these controllers. It works for
88SX6111, but 88SX6145 always returns zero there. Haven't tested others,
but better to be safe.
correctly:
* pass in whether to allow the hardware to override the duration field
in the main data frame (durupdate_en) - PS_POLL frames in particular
don't have the duration bit overriden;
* there's no rts/cts duration here; that's done elsehwere
a number of cores, this allows for a sparse set of CPUs. Implement support
for sparse core masks on Octeon.
XXX jeff@ suggests that all_cpus should include cores that are offline or
running other applications/OSes, so the platform API should be further
extended to allow us to set all_cpus to include all cores that are
physically-present as opposed to only those that are running FreeBSD.
Submitted by: Bhanu Prakash (with modifications)
Reviewed by: jchandra
Glanced at by: kib, jeff, jhb
KASSERT()s and eliminate the rest.
Replace excessive printf()s and a panic() in bufdone_finish() with a
KASSERT() in vm_page_io_finish().
Reviewed by: kib
Resort the CURVNET_SET* macros in the non-VNET_DEBUG case to match
the call order of the VNET_DEBUG case.
Add the VNET_ASSERT() to the non-VNET_DEBUG case as well so that
INVARIANTS will still catch problems.
Sponsored by: The FreeBSD Foundation
Sponsored by: CK Software GmbH
Reviewed by: jhb
MFC after: 2 weeks
Make VNET_ASSERT() available with either VNET_DEBUG or INVARIANTS.
Change the syntax to match KASSERT() to allow more flexible panic
messages rather than having a printf with hardcoded arguments
before panic.
Adjust the few assertions we have to the new format (and enhance
the output).
Sponsored by: The FreeBSD Foundation
Sponsored by: CK Software GmbH
Reviewed by: jhb
MFC after: 2 weeks
attached, activate the page after the successful read, and free the page
if read was unsuccessfull.
Freshly allocated page is not on any queue yet, and not activating (or
deactivating) the page leaves it on no queue, excluding the page from
pagedaemon scans and making the memory disappeared until the vnode
reclaimed.
Reviewed by: avg
MFC after: 1 week
- this also includes virtualization support on these devices
Correct some vlan issues we were seeing in test, jumbo frames on vlans
did not work correctly, this was all due to confused logic around HW
filters, the new code should now work for all uses.
Important fix: when mbuf resources are depeleted, it was possible to
completely empty the RX ring, and then the RX engine would stall
forever. This is fixed by a flag being set whenever the refresh code
fails due to an mbuf shortage, also the local timer now makes sure
that all queues get an interrupt when it runs, the interrupt code
will then always call rxeof, and in that routine the first thing done
is now to check the refresh flag and call refresh_mbufs. This has been
verified to fix this type 'hang'. Similar code will follow in the other
drivers.
Finally, sync up shared code for the I350 support.
Thanks to everyone that has been reporting issues, and helping in the
debug/test process!!
to construct the full pathname. It starts to search at the default
mountpoint which is /dev/shm. If this fails it runs through fstab
and searches for shmfs and tmpfs. Whatever it finds will be
statfs()'ed to be checked for Linux' fs magic for shmfs (0x01021994).
Ideally our tmpfs should deliver this fs magic to Linux processes, but
as our tmpfs is considered to be an experimental feature we can not
assume that there is always a tmpfs available.
To make shared memory work in the Linuxulator, force the fs type of
/dev/shm (which can be a symlink) to match what Linux expects. The user
is responsible (info has to be added to the linux base ports and the docs)
to setup a suitable link for /dev/shm.
Noticed by: Andre Albsmeier <Andre.Albsmeier@siemens.com>
Submitted by: Andre Albsmeier <Andre.Albsmeier@siemens.com>
MFC after: 1 month
attributes for preloaded modules/images. In particular, MODINFO_ADDR has
the added complexity of not always being relocated properly. Rather than
kluging this in the various components that are affected, we handle it
in a centralized place (preload_fetch_addr()). To that end, expose a new
variable, preload_addr_relocate, that MD initialization code can set and
that turns the address attribute into a valid kernel VA.
Architectures that need the relocation: arm & powerpc (at least).
Components that can utilize this: acpi(4), md(4), fb(4), pci(4), ZFS, geli.
Sponsored by: Juniper Networks
Drivers which rely on net80211 to create the beacon need to call
ieee80211_beacon_update() on iv_update_beacon() calls. This is required
that certain bits, e.g. TIM, get updated. A call to ieee80211_beacon_alloc()
is not enough because it does not care about flags which can only change
during runtime. By design a beacon is supposed to be allocated only once
while moving into RUN state.
To handle all possible calls to iv_update_beacon() the run_updateslot()
function has been revived and run_updateprot() has been added.
run_updateslot() handles slot time changes and run_updateprot() changes
to protection, both can change while nodes associate/leave.
Submitted by: Alexander Zagrebin <alex at zagrebin.ru>,
PseudoCylon <moonlightakkiy atyahoo.ca>
MFC after: 3 weeks
There's still a lot of random issues to sort out with the radio side of
things and AMPDU RX handling (and completely missing AMPDU TX handling!)
but if people wish to give this a go and assist in debugging the
issues, they can define ATH_DO_11N to enable it.
I'm just re-iterating - this is here to allow people to assist in
further 11n development; it is not any indication that the 11n support
is complete and functional.
Important notes:
* This doesn't support 1-stream cards yet - (eg AR9285) - the various bits
that negotiate TX/RX MCS don't know not to try >1 stream TX or negotiate
1-stream RX; so don't enable 11n unless you've first taught the rate
control module and the net80211 stack to negotiate 1-stream stuff;
* The only rate control module minimally 11n aware is ath_rate_sample;
* ath_rate_sample doesn't know about HT/40; so airtime will be incorrectly
calculated;
* The AR9160 and AR9280 radio code is unreliable at the higher MCS rates for
some reason; this will definitely impact 11n performance;
* AMPDU-TX isn't yet implemented;
* AMPDU-RX may be a bit buggy still and will definitely suffer from the
radio unreliability mentioned above (ie, don't expect 150/300mbit
RX just yet.)
SU+J is not included as a FEATURE macro:
- it was not in the tree during the GSoC
- I do not see an option to en-/disable it in NOTES
Two minor changes where made during the review compared to what was developed
during GSoC 2010.
No FreeBSD version bump, the userland application to query the features will
be committed last and can serve as an indication of the availablility if
needed.
Sponsored by: Google Summer of Code 2010
Submitted by: kibab
Reviewed by: kib
X-MFC after: to be determined in last commit with code from this project
The correct bit to set is 0x1 in the high MAC address byte, not 0x80.
The hardware isn't programmed with that bit (which is the multicast
adress bit.)
The linux ath9k keycache code uses that bit in the MAC as a "this is
a multicast key!" and doesn't set the AR_KEYTABLE_VALID bit.
This tells the hardware the MAC isn't to be used for unicast destination
matching but it can be used for multicast bssid traffic.
This fixes some encryption problems in station mode.
PR: kern/154598
- use device_printf() instead of printf() to give more accurate warnings.
- use memcpy() instead of bcopy().
- add missing #if's for non-FreeBSD compilation.
Approved by: thompsa (mentor)
error address on a decoding error to unlatch it and to allow
us to print a better diagnostics message. This also has the
side effect of clearing the condition, which prevents an
interrupt storm.
Revert back to the previous method of doing it for where a node can be
identified and it's an 11n node.
I'll have to do some further research into exactly what is being messed up
with the sequence number matching and I'll then revisit this.
This doesn't yet take into account HT40 packet durations as the node info
(needed to know if it's a HT20 or HT40 node) isn't available everywhere
it needs to be.
free i-nodes or blocks to handle a race where another thread might have
allocated the last i-node or block while we were waiting for the buffer.
Tested by: dougb
putting descriptors (not buffers) across a 4k page boundary can cause issues.
I've not seen it in production myself but it apparently can cause problems.
So, in preparation for addressing this workaround, (re)-expose the particular
HAL capability bit which marks whether the chipset has support for cross-4k-
boundary transactions or not.
A subsequent commit will modify the descriptor allocation to avoid allocating
descriptor entries that straddle a 4k page boundary.
a hard hang due to an interrupt storm or stuck interrupt pin. We
return the next IRQ that is larger than the last one returned and
in doing so give all interrupts a fair chance of being handled.
Consequently, we're able to break into the kernel debugger in such
an event.
masked-off by the firmware.
o In DELAY(). Make sure we have an inner-loop body that the compiler
cannot eliminate. While timing does not have to be perfect, the
loops must be there to have at least some notion of delay.
Obtained from: Juniper Networks
misnamed since it was introduced and should not be globally exposed
with this name. The equivalent functionality is now available using
kern_yield(curthread->td_user_pri). The function remains
undocumented.
Bump __FreeBSD_version.
- entirely eliminate some calls to uio_yeild() as being unnecessary,
such as in a sysctl handler.
- move should_yield() and maybe_yield() to kern_synch.c and move the
prototypes from sys/uio.h to sys/proc.h
- add a slightly more generic kern_yield() that can replace the
functionality of uio_yield().
- replace source uses of uio_yield() with the functional equivalent,
or in some cases do not change the thread priority when switching.
- fix a logic inversion bug in vlrureclaim(), pointed out by bde@.
- instead of using the per-cpu last switched ticks, use a per thread
variable for should_yield(). With PREEMPTION, the only reasonable
use of this is to determine if a lock has been held a long time and
relinquish it. Without PREEMPTION, this is essentially the same as
the per-cpu variable.
* The existing radio config code was for the AR5416/AR9160 and missed out
on some of the AR9280 specific stuff. Include said stuff from ath9k.
* Refactor out the gain control settings into a new function, again pilfered
from ath9k.
* Use the analog register RMW macro when touching analog registers.
Obtained from: Linux ath9k
calling thread's unique integral ID, which is similar to AIX function of
the same name. Bump __FreeBSD_version to note its introduction.
Reviewed by: kib
* Store the flowid when receiving an SCTP/IPv6 packet.
* Store the flowid when receiving an SCTP packet with wrong CRC.
* Initilize flowid correctly.
* Put test code under INVARIANTS.
MFC after: 3 months.
Clear the padding when returning context to the usermode, for
MI ucontext_t and x86 MD parts.
Kernel allocates the structures on the stack, and not clearing
reserved fields and paddings causes leakage.
pins to determine whether there's a high register set or not. This
allows platform_gpio_init() to work without duplicating the work
done in the attach method.
o) Have mips_wblush just do syncw, not sync on Cavium Octeon.
o) Add support for reading and writing some Octeon-specific registers.
NB: Some of these are not entirely Octeon-specific.
Submitted by: Bhanu Prakash
This fixes two problems -
* All packets need to be processed here, not just aggregate ones - as any
received frames (AMPDU or otherwise) in the given TID (traffic class id)
will update the sequence number and, implied with that, update the window;
* It seems there's situations where packets aren't matching a current node but
somehow need to be tracked. Thus just tag them all for now; I'll figure out
the why later.
Whilst I'm here, bump the stats counters whilst I'm at it.
This fixes AMPDU RX in my tests; the main problems now stem from what look
like PHY level error/retransmits which are impeding general throughput, incl.
AMPDU.
In the dec.2009 rewrite I introduced a bug, using for the
computation the arrival time instead of the time the packet
has exited from the queue.
The bandwidth computation was still correct because it is
computed elsewhere, but traffic was sent out in bursts.
The bug is also present in RELENG_8 after dec.2009
Thanks to Daikichi Osuga for investingating, finding and fixing the
bug with detailed graphs of the behaviour before and after the fix.
Submitted by: Daikichi Osuga
MFC after: 2 weeks
TX chainmask.
since the upper layers don't (yet) know about the active TX/RX chainmasks,
it can't tell the rate scenario functions what to use. I'll eventually sort
this out; this restores functionality in the meantime.
incorrectly calling vm_object_page_clean(). They are passing the length of
the range rather than the ending offset of the range.
Perform the OFF_TO_IDX() conversion in vm_object_page_clean() rather than the
callers.
Reviewed by: kib
MFC after: 3 weeks
MI ucontext_t and x86 MD parts.
Kernel allocates the structures on the stack, and not clearing
reserved fields and paddings causes leakage.
Noted and discussed with: bde
MFC after: 2 weeks
controller in question generates frames with bad IP checksum value
if packets contain IP options. For instance, packets generated by
ping(8) with record route option have wrong IP checksum value. The
controller correctly computes checksum for normal TCP/UDP packets
though.
There are two known RTL8168/8111C variants in market and the issue
I observed happened on RL_HWREV_8168C_SPIN2. I'm not sure
RL_HWREV_8168C also has the same issue but it would be better to
assume it has the same issue since they shall share same core.
RTL8102E which is supposed to be released at the time of
RTL8168/8111C announcement does not have the issue.
Tested by: Konstantin V. Krotov ( kkv <> insysnet dot ru )
