are not supported by this implementation, and the error return values
from sem_init(), sem_open(), sem_close(), and sem_unlink() reflect this.
Approved by: jkh
- Sync ohci, uhci and usbdi modules with NetBSD in order to obtain the
following improvements:
o New USBD_NO_TSLEEP flag can be used in place of UQ_NO_TSLEEP
quirk. This allows drivers to specify busy waiting only for
certain transfers (namely control transfers for reading/writing
registers and stuff).
o New USBD_FORCE_SHORT_XFER flag can be used to deal with
devices like the ADMtek Pegasus that sense the end of bulk OUT
transfers in a special way (if a transfer is exactly a multiple
of 64 bytes in size, you need to send an extra empty packet
to terminate the transfer).
o usbd_open_pipe_intr() now accepts an interval argument which
can be used to change the rate at which the interrupt callback
routine is invoked. Specifying USBD_DEFAULT_INTERVAL uses the
value specified in the device's config data, but drivers can
override it if needed.
- Change if_aue to use USBD_FORCE_SHORT_XFER for packet transmissions.
- Change if_aue, if_kue and if_cue to use USBD_NO_TSLEEP for all
control transfers. We no longer force the non-tsleep hack for
bulk transfers since these are done asynchronously anyway.
- Removed quirk entry fiddling from if_aue and if_kue since we don't
need it anymore now that we have the USBD_NO_TSLEEP flag.
- Tweak ulpt, uhid, ums and ukbd drivers to use the new arg to
usbd_open_pipe_intr().
- Add a flag to the softc struct in the ethernet drivers to indicate
when a device has been detached, and use this flag to perform
tests to prevent the drivers from trying to do control transfers
if this is the case. This is necessary because calling if_detach()
with INET6 enabled will eventually result in a call to the driver's
ioctl() routine to delete the multicast groups on the interface,
which will result in attempts to perform control transfers. (It's
possible this also happens even without INET6 support enabled.) This
is pointless since we know that if the detach method has been called,
the hardware has been unplugged.
- Changed watchdog timeout routines to just call the driver init routines
to initialize the device states without trying to close and re-open the
pipes. This is partly because we don't want to frob things at interrupt
context, but also because this doesn't seem to work right and I don't
want to panic the system just because a USB device may have stopped
responding.
- Fix aue_rxeof() to be a little smarter about detecting when a double
transfer is needed. Unfortunately, the design of the chip makes it hard
to get this exactly right. Hopefully, this will go away once either
Nick or Lennart finds the bug in the uhci driver that makes this ugly
hack necessary.
- Also sync usbdevs with NetBSD.
file open in one of the special file descriptors (0, 1, or 2), close
it before completing the exec.
Submitted by: nergal@idea.avet.com.pl
Constructive comments: deraadt@openbsd.org, sef, peter, jkh
and concat these to the corresponding generic *.TXT living in ./texts
This is currently aimed at HARDWARE.TXT but works for things like RELNOTES.TXT
too.
Reviewed by: jkh
garbage value for the username (hex garbage, that is), and the -d flag
provides a default username for fallback purposes if the user cannot be
looked up. That is very useful for the case where inetd auth is
running on a NAT box.
While I'm here updating the manpage, clean up an English error and a
few small nits.
This is just to make sure we initialize the chip correctly: we need to
make the sure the port select bit in CSR6 is set properly so that we
use the internal PHY for 10/100 support. (The eval boards I have also
include an external HomePNA PHY, but I need to play with that more
before I can support it.)
We were supposed to get these in far earlier and didn't, hence
the commit after feature freeze. A promise is a promise. :)
Submitted by: Sascha Schumann <sascha@schumann.cx>
with remote hosts feeding it, so that some hosts have their header
pages supressed and some don't. This is because lpd doesn't know
how to rewrite a print job before forwarding it to a remote lpd.
In particular this causes problems with p rinters that contain
their own lpd, eg. HP jet direct cards, because they can't suppress
headers. It's not possible to have headers supressed by putting
'sh' in any printcap in the lpd chain, it is up to the originating
lpr to have a '-h' option specified at run time.
Lpr has been modified to allow _it_ to honour the 'sh' flag in the
local print cap. This allows the administrator to switch off
headers for a particular printer (on a particular host) irrespective
of whether that printer is local to the machine or remote.
This doesn't break anything, because in the case of a remote printer
the 'sh' flag would have had no meaning, in the case of the local
printer it would have been on anyway.
Submitted by: Scott James Remnant <scott@pavilion.net>
nnn at pc 0xADDR" and the fixup of the UA fault on the DEC Alpha when an
unaligned access fault happens. Modeled after the OSF/1 utility of the
same name.
Submitted by: gallatin
signal handler. Explicitly check for jumps to anywhere other than the
current stack, since such jumps are undefined according to POSIX.
While we're at it, convert thread cancellation to use continuations, since
it's cleaner than the original cancellation code.
Avoid delivering a signal to a thread twice. This was a pre-existing bug,
but was likely unexposed until these other changes were made.
Defer signals generated by pthread_kill() so that they can be delivered on
the appropriate stack. deischen claims that this is unnecessary, which is
likely true, but without this change, pthread_kill() can cause undefined
priority queue states and/or PANICs in [sig|_]longjmp(), so I'm leaving
this in for now. To compile this code out and exercise the bug, define
the _NO_UNDISPATCH cpp macro. Defining _PTHREADS_INVARIANTS as well will
cause earlier crashes.
PR: kern/14685
Collaboration with: deischen
prettier (?) names, adding some const's around here, et al.
This is commit 4 out of 3, updating the userland library to reflect kernel
interface changes.
Reviewed by: bde
check for on the server may arise legitimately on the client. The
correct way to check for a zero record length is to check for it
without the LAST_FRAG marker in it, since it's legal to send a LAST_FRAG
marker with 0 bytes of data.
PR: misc/16028
