apparently possible) event that the transmit start routine is
called with and empty if_snd queue, bail out instead of dereferencing
unilitialized transmit list pointers and panicking.
suggested compilation cleanups from Eklund. Wire down a hard loop id if we are
not on a platform that has the ability to get to a PCI BIOS (it still will
float to the ID it gets after a LIP but at least we can try). Clarify that the
expanded lun is based upon SCCLUN defines (in f/w).
for possible buffer overflow problems. Replaced most sprintf()'s
with snprintf(); for others cases, added terminating NUL bytes where
appropriate, replaced constants like "16" with sizeof(), etc.
These changes include several bug fixes, but most changes are for
maintainability's sake. Any instance where it wasn't "immediately
obvious" that a buffer overflow could not occur was made safer.
Reviewed by: Bruce Evans <bde@zeta.org.au>
Reviewed by: Matthew Dillon <dillon@apollo.backplane.com>
Reviewed by: Mike Spengler <mks@networkcs.com>
PCI fast ethernet adapters, plus man pages.
if_pn.c: Netgear FA310TX model D1, LinkSys LNE100TX, Matrox FastNIC 10/100,
various other PNIC devices
if_mx.c: NDC Communications SOHOware SFA100 (Macronix 98713A), various
other boards based on the Macronix 98713, 98713A, 98715, 98715A
and 98725 chips
if_vr.c: D-Link DFE530-TX, other boards based on the VIA Rhine and
Rhine II chips (note: the D-Link and certain other cards
that actually use a Rhine II chip still return the PCI
device ID of the Rhine I. I don't know why, and it doesn't
really matter since the driver treats both chips the same
anyway.)
if_wb.c: Trendware TE100-PCIE and various other cards based on the
Winbond W89C840F chip (the Trendware card is identical to
the sample boards Winbond sent me, so who knows how many
clones there are running around)
All drivers include support for ifmedia, BPF and hardware multicast
filtering.
Also updated GENERIC, LINT, RELNOTES.TXT, userconfig and
sysinstall device list.
I also have a driver for the ASIX AX88140A in the works.
is completely empty. There is an interrupt for output completion. It
is painful to use, but polling method used in the corresponding fix in
sio.c (rev.1.152) can't be used because there is no status bit for
transmitter-empty. Now ttywait() works right.
Reminded by: NIST-PCTS
Don't call timeout() for DTR wakeup if the relevant timeout is already
active. This fixes "timeout table full" panics when sufficiently many
cyopen()s are interrupted while they are sleeping waiting for the
timeout to expire.
cards. My machine didn't tickle this problem, so I can't tell if
it fixed anything or not. However, it didn't break my already working
1542-{B,C,CF,CP} probes.
o Minor comment correction
o Minor correction in printf
were half of their physical offsets for ISA and 1/4 of their physical
offsets for PCI, while all other Cyclades offsets were physical/1 for
ISA and physical/2 for PCI. Logically wrong macros were used to scale
CY16_RESET and CY_CLEAR_INTR to the correct physical offsets.
Fixed some style bugs (mostly long lines).
use a 256 entry ring buffer of descriptersfor this purpose. This allows
the use of a simple 8bit counter in the sequencer code for tracking start
location.
Entries in the ring buffer now contain a "cmd_valid" byte at their tail.
As an entry is serviced, this byte is cleared by the kernel and set by
the sequencer during its dma of a new entry. Since this byte is the last
portion of the command touched during a dma, the kernel can use this
byte to ensure the command it processes is completely valid.
The new command format requires a fixed sized DMA from the controller
to deliver which allowed for additional simplification of the sequencer
code. The hack that required 1 SCB slot to be stolen for incoming
command delivery notification is also gone.
interrupt handlers. Instead, load and use it atomically as necessary.
This reduces mode switching overhead for "polled" mode interrupt handling
from 5 i/o's to 3 (per service type, per port) so that polled mode is only
slightly more inefficient than "interrupt" mode.
* Update drivers to the latest version of the bus interface.
The ISA drivers' use of the new resource api is minimal. Garrett has
some much cleaner drivers which should be more easily shared between
i386 and alpha. This has only been tested on cia based machines. It
should work on lca and apecs but I might have broken something.
If the next available mailbox is not in the free state, print a warning
and handle the condition as a temporary resource shortage. The condition
should never happen, but we shouldn't panic since recovery is possible.
Convert from BT'isms to AHA'isms
Don't fail the probe if the illegal command bit is set in the status
register. If the BusLogic MultiMaster probe preceeded us, it may well
have determined that the card we are attaching to was not a true MultiMaster
by sending us a command that fails on the 154X.
Reset the adapter before doing the inquiry. This provides extra sanity
and will also clear the illegal command status bit that my be left over
from the MultiMaster probe.
truncated to 32 bits.
* Change the calling convention of the device mmap entry point to
pass a vm_offset_t instead of an int for the offset allowing
devices with a larger memory map than (1<<32) to be supported
on the alpha (/dev/mem is one such).
These changes are required to allow the X server to mmap the various
I/O regions used for device port and memory access on the alpha.
base register that controls Ultra-DMA, so we need to examine all possible
base registers instead of just giving up at the first empty one.
Also, looking at the source code to the BIOS, I see that they are also
checking for 0xffffffff as an invalid value so do the same. Stefan may like
to clean this up, but at least now I can find my PCI IDE registers.
the top half to do it.
Put in a dubious check for subdisk integrity when trying to bring
up a plex where others are already up. This particular kludge is
crying out for a rewrite of the whole state code.
Add code to set_plex_state and set_volume_state to defer updates when
called from an interrupt context. This doesn't happen yet, but it
could do.
basic i/o functions, bit-banging mechanism is implemented by dev/iicbus/iicbb.c
immio.c: some bootverbose logs to watch zip+ connect/disconnect process
config_drive:
Catch an instance of anonymous drives. Doubtless many remain.
interrupt.c:
complete_rqe:
Call logrq to log iodone events if DEBUG_LASTREQS is set.
Call set_sd_state with setstate_noupdate to avoid buffered I/O out
of interrupt context.
Use define DEBUG_RESID instead of constant.
memory.c:
Remove dead expandrq() function
Malloc:
Remove directory component of file names in malloc table.
Add function vinum_rqinfo (part of the request tracing stuff).
request.c:
Add function logrq (part of the request tracing stuff).
vinumstrategy:
Check whether config needs to be written to disk, do it if so.
This is a stopgap until the Vinum daemon (bacchusd? oenologistd?)
is written.
If DEBUG_LASTREQS is set, call logrq to log user buffer headers.
launch_requests:
Correct format of debug output to console.
If DEBUG_LASTREQS is set, call logrq to log request elements.
request.h:
Add definitions for request trace.
state.c:
set_sd_state:
Check flags for setstate_noupdate. If set, don't write the config
to disk, just set global VF_DIRTYCONFIG flag. This is part of the
kludge to avoid writing config from an interrupt context.
vinumext.h:
Add declaration for vinum_rqinfo, put inside #ifdef DEBUG
Remove dead macro expandrq
vinumio.h:
Increase maximum ioctl reply length to 4 kB if DEBUG is set.
Define VINUM_RQINFO ioctl if DEBUG is set.
vinumioctl.c:
vinumioctl:
Change implementation of VINUM_DEBUG ioctl: use a debug flag
(DEBUG_REMOTEGDB) to decide whether to go into remote debugging or
not.
Implement VINUM_RQINFO.
vinumkw.h:
Define kw_info even when not debugging.
vinumvar.h:
Define VF_DIRTYCONFIG
Add pointers to request info to vinum_info if DEBUG is set.
Define setstate_noupdate
Define additional debug bits DEBUG_RESID, DEBUG_LASTREQS and
DEBUG_REMOTEGDB.
Correct a problem where an external bus reset on the 'background' channel of
a Twin Channel EISA controller could put the driver into an infinite loop.
Noticed by: Twin Channel bug, Joerg Wunsch <joerg@FreeBSD.org>
Submitted by: -Wunused, Poul-Henning Kamp <phk@freebsd.org>
Fixed bug in advansys.c where we did not properly clean up ccb_info data
structures in softc teardown.
Submitted by: Poul-Henning Kamp <phk@freebsd.org>
bogus comment to proper place.
This should fix the hangs people are seeing under very heavy load, at
least it does for me. Please let me know if you continue to have
problems.
hasseen_isadev so this will be less noisy when conflicts do exist.
Also eliminate redundant warnings about conflicts.
Requested by: bde
Reviewed by: gibbs
fxp_stop is called as the first thing in fxp_init, and if the tx desc
list has junk in it, the system may panic. This bug showed up as a side
effect of the changes in rev 1.56, but has been in the code since the
beginning.
this myself for ages, but wasn't able to get any feedback from the people
that I sent it to for testing.
Guy Helmer <ghelmer@scl.ameslab.gov> has given it a shot (before getting on
a plane, thanks!) and it appears to stop his reproducable page fault panic
in the testing he was able to do.
o For bt and aha only probe the one I/O range if a specific I/O is specified
in the config file.
o Don't even try to probe I/O ranges that have been seen already.
o If we conflict with an IRQ or DRQ, then fail the probe.
Requested by: bde, gibbs
Approved by: jkh
is a work-around from an LRAM access bug on the 940UA. In a future
microcode revision, the high 16bits of residual information will be moved
to a safe location and we'll return to 32bit residuals. Since we only
allow 64KB I/O, 16bits is enough.
DEB macro). There are probably quite a few other messages that warrant
a similar treatment, and many more that should be converted to plain
log messages (e.g. "WARNING: wrintr but write DMA inactive!"). Now
that I think of it, same goes for the CAM code (e.g. the famed "tagged
openings" message)
Disable DPARCKEN in the DSCOMMAND0 register on the aic7890/91/96/97.
Parity checking is broken for some chip/MB combinations and this
is the work around recommended by Adaptec.
dpt_pci.c:
Remove a superflous '{' that prevented DPT_ALLOW_MEMIO from working.
pcireg.h:
Add a definition for Parity Error Reponse bit in the PCI Space
command register.
queued.
Perform dma segment setup outside of splcam protection as this can take
some time and the protection is not necessary.
Inline a function.
Clean up some whitespace.
routines are necessary to allow the use of certain types of hardware on
the alpha, particularly a Myrinet card.
Submitted by: Andrew Gallatin <gallatin@cs.duke.edu>
reported bug.
At using tcpdump for cs interface, tcpdump only dump packet which
src or dst MAC-address is cs interface. cs interface can't look up
packet between others.
Submitted by: MIHIRA "Sanpei" Yoshiro <sanpei@sanpei.org>
add support for Vibra16X, OPTi925, and bring in several assorted
fixes to the code and documentation.
Also present here are apm hooks so that laptops can properly
reconfigure the hardware after suspend (tested on the Libretto50).
Reviewed by: jordan
- Express various sizes in bytes, rather than Kbytes, in the video
mode and adapter information structures.
- Fill 0 in the linear buffer size field if the linear frame buffer
is not available.
- Remove SW_VESA_USER ioctl. It is still experimetal and was not meant
to be released.
- Fix missing cast operator.
- Correctly handle pointers returned by the VESA BIOS. The pointers
may point to the area either in the BIOS ROM or in the buffer supplied
by the caller.
- Set the destructive cursor at the right moment.
o Use the board id command to find out what kind of board
we're talking to. If we're talking to a board that is has
an ID that is shared between boards supported by the aha
driver and the bt driver, then use the bt's geometry
register to weed out the bt cards. Otherwise assume that we
support this card.
o Remove bt esetup command sending to the card. It seems to
wedge too many cards.
o Revert to doing a soft reset after an invalid command. This
change didn't fix anything, so I'm backing it out. The
whole issue of card resetting needs to be revisisted at some
point so that we can do it properly on all hardware.
o GC unused stuff in some places.
o Unlock mailbox interface if we have a new card. Before only newer cards
(B or newer) that had the BIOS disabled would probe. Cards with the
BIOS enabled would fail to probe in the mailbox initialization code.
o Increase the number of ccbs and sg to 17 from 16 to support 64k I/O
on a non page aligned boundary. Ideas for dynamic determination of this
value welcomed, as more of these are better.
o Took credit for this driver, even though I derived it from Justin's code.
Made sure that Justin's copyright from bt.c was preserved, along with
his name, since the error handling code is nearly identical. Add my
own, identical copyright. Point people to aha_isa.c.
Cards tested: 1542C and 1542CF. The B and CP might work now as well,
but logistical problems precluded me from testing them this evening
(if you have jumper settings for the B card, please send me private
mail).
- there were too many global variables (there still are :-).
- the data section was bloated by explicit initializations of static
variables to 0 (only fixed the recently changed ones).
- WRAPHIST() had silly parentheses around foo->bar.
- the comment about inline functions was stale.
- the comment about Userconfig presumes too much about the boot environment.
- `i' was reused confusingly in scioctl().
- the declaration of `butmap' used a deprecated K&R misfeature.
- the initializeation of `butmap' had an unnecessary line break.
- `unsigned char' was not consistently (mis)spelled as u_char.
- English was poor in a comment in videoio.c.
Submitted by: bde
- Handle pixel (raster text) mode properly.
- Clear screen and paint border right.
- Paint text attribute (colors).
- Fix off-by-one errors.
- Add some sanity checks.
- Fix some function prototypes.
- Add some comment lines.
- Define generic text mode numbers so that the user can just give
"80x25", "80x60", "132x25"..., rather than "VGA_xxx", to `vidcontrol'
to change the current video mode. `vidoio.c' and `vesa.c' will map
these numbers to real video mode numbers appropriate and available
with the given video hardware. I believe this will be useful to make
syscons more portable across archtectures.
Bump the lun field in the eata ccb to 5 bits. We still only
use 3 of them, but we may use the rest at a later date.
dpt_scsi.c:
Default to only 32 S/G segments.
Bzero our CCB array after allocation.
- ppbus was released before checking if still in disk_mode by vpoio and immio:
the microseq (in_disk_mode) was never executed. Fixed.
- nlptintr() renamed to nlpt_intr(). spltty() inserted in nlptintr() before
nlpt_intr() call
those extra ones yet, anyway.
In dpttimeout, expect that the controller will complete aborted CCBs through
the interrupt handler. This corrects a panic that was caused by completing
the same transaction twice during timeout recovery.
Honor the tag times types expressed by the user and pass them down to
the controller.
a timeout, we must remove the pending SCB from the disconnected list
or risk list corruption when our BDR request using the same SCB is placed
on the waiting list.
Eradicate some silly uses of u_int8_t that just serve to slow the code down.
+ Change some messages about CCB memory allocation
+ Turn a failure to DMA map all of a transaction due to lack of
ISP queue entries into a requeue operation (instead of the
case where it had been treated the same as a DMA too big
operation).
+ put back splsoftvm around bus_dmamap_load calls.
+ cleanup (and fix a glaring bug) in the and of the dma setup
routine. Also, the dma setup routines either return CMD_QUEUED
(for success) or CMD_COMPLETE (for failure) or CMD_EAGAIN
(for requeuing for resource shortage reasons).
Kazu writes:
The VESA support code requires vm86 support. Make sure your kernel
configuration file has the following line.
options "VM86"
If you want to statically link the VESA support code to the kernel,
add the following option to the kernel configuration file.
options "VESA"
The vidcontrol command now accepts the following video mode names:
VESA_132x25, VESA_132x43, VESA_132x50, VESA_132x60, VESA_800x600
The VESA_800x600 mode is a raster display mode. The 80x25 text will
be displayed on the 800x600 screen. Useful for some laptop computers.
vidcontrol accepts the new `-i <info>' option, where <info> must be
either `adapter' or `mode'. When the `-i adapter' option is given,
vidcontrol will print basic information (not much) on the video
adapter. When the `-i mode' option is specified, vidcontrol will
list video modes which are actually supported by the video adapter.
Submitted by: Kazutaka YOKOTA yokota@FreeBSD.ORG
Host ATM Research Platform (HARP), Network Computing Services, Inc.
This software was developed with the support of the Defense Advanced
Research Projects Agency (DARPA).
- Convert to CAM
- Use a new DMA based queuing and paging scheme
- Add preliminary target mode support
- Add support for the aic789X chips
- Take advantage of external SRAM on more controllers.
- Numerous bug fixes and performance improvements.
and use this when masking/unmasking interrupts.
Maintain a mapping from (iopaic number, int pin) tuple to irq number,
and use this when configuring devices and programming the ioapics.
Previous code assumed that irq number was equal to int pin number, and
that the ioapic number was 0.
Don't let an AP enter _cpu_switch before all local apics are initialized.
Removed Hauppauge EEPROM 0x10 detection as I think 0x10 should be a
PAL tuner, not NTSC.
Reinstated some Tuner Guesswork code from 1.27
Submitted by: Roger Hardiman <roger@cs.strath.ac.uk>
Added PR kern/7177 for SECAM Video Highway Xtreme with single crystal
PLL configuration submitted by Vsevolod Lobko <seva@alex-ua.com>.
In kernel configuration file add
options OVERRIDE_CARD=2
options OVERRIDE_TUNER=11
options BKTR_USE_PLL
Submitted by: Roger Hardiman <roger@cs.strath.ac.uk>
Normally the full 640x480 (768x576 PAL) image is grabbed. This ioctl
allows a smaller area from anywhere within the video image to be
grabbed, eg a 400x300 image from (50,10).
See restrictions in BT848SCAPAREA.
Submitted by: Roger Hardiman <roger@cs.strath.ac.uk>
Add a sysctl 'machdep.cs_recv_delay' to specify how long to wait after
receiving a packet in order to check for a subsequent (back-to-back)
packet. The cs8900 has a very small receive buffer, so this helps avoid
overflows at the cost of some extra CPU overhead.
Submitted by: Oleg Sharoiko <os@rsu.ru>, MIHIRA "Sanpei" Yoshiro <sanpei@sanpei.org>
for the Lite2 fix for always returning EIO in dead_read().
Cleaned up the cdevswitch initializers for all tty drivers.
Removed explicit calls to ttsetwater() from all (tty) drivers. ttsetwater()
is now called centrally for opens, not just for parameter changes.
The check for dropping unicast packets not sent to our ethernet
address is after the bpf tap, but not conditioned on it. All packets
received should get handed to bpf, and unicast packets not to us (mac)
should get dropped whether or not there is a bpf listener. I believe
that the common optimization that the interface is in hw promisc mode
iff there is a bpf listener is in general wrong, but more frequently
so on wavelans.
I think Max's fix makes bpf listeners not see unicast packets sent to
others, but I'm not sure.
One can argue that checking on MOD_ENAL is wrong, but the code only
drops packets that shouldn't be received. The correctness condition
is that it be run whenever unicast packets without our mac address can
be received.
PR: kern/7144
Submitted by: Greg Troxel <gdt@ir.bbn.com>
for 1 second's worth of input) and larger tty output buffers. The
interrupt-level buffers are still too small for speeds above 115200
bps (only a little too small for 230400 bps if RTS flow control is
enabled).
Don't call ttsetwater() explicitly in open(). It is now called for
the TTYDISC l_open() and should be static.
Don't attempt to register the cdevsw more than once.
description of DPT_SHUTDOWN_SLEEP in LINT. Didn't add timestamps
so that the (combined?) sleep interval can be printed as intended
in the original printf.
stability now. ALso modify /sys/conf/files, /sys/i386/conf/GENERIC
and /sys/i386/conf/LINT to add entries for the XL driver. Deactivate
support for the XL adapters in the vortex driver. LAstly, add a man
page.
(Also added an MLINKS entry for the ThunderLAN man page which I forgot
previously.)
of invariants to cyattach().
Fixed minor bugs:
- cyparam() returned without restoring the ipl in the error cases. This
was harmless because cyparam() is always called at spltty().
- one check for "rev. J or higher" actually checked for precisely rev. J.
swapped RTS/DTR). Merge the vendor's modification of the 2.2.6-release
version into -current for reference. Will be cleaned up in next commit.
Obtained from: ftp://ftp.cyclades.com/pub/cyclades/cyclom-y/freebsd/2.2.6/cyy226.tar.gz
was broken), 1.30 (COMPAT_43 option header was missing), 1.31 (DEVFS
option header was missing), 1.33 (garbage pointers were followed
in debugging code). Cosmetic changes from 1.27, 1.32, 1.36, 1.37.
Of course, the DEVFS code didn't even compile. Fixed. Not tested.
Forgotten by: brian
This file should not exist. It is the same as dgb.c except for lots of
renamed variables, about 250 lines removed, and only about 100 lines of
real differences.
instead of at compile time using ifdefs.
Use _swi_null instead of dummycamisr. CAM and dpt should call
register_swi() instead of hacking on ihandlers[] directly.
