This abstracts out all the differences I could see between the netbsd
sparc64 and macppc zs drivers. In particular the offsets of the csr and
data registers are different, so we use a separate bus handle for each and
use bus_space_subregion to add the bus specific offsets.
Requested by: benno
as separate 16-bit entities. Some of the ring control blocks are
in NIC memory, so they must be referenced using 32-bit accesses.
Smaller accesses have been observed to fail under some conditions.
This caused the rings to be set up wrong, leading to writes by the
card outside of the intended bounds of the rings. This problem was
diagnosed by Michael Barthelow. Don Bowman submitted a patch which
fixed the problem using a slightly different approach.
Reference ring control blocks in NIC memory using a pointer to
volatile.
Parenthesize the BGE_HOSTADDR macro definition properly.
MFC after: 3 days
from the hardware descriptors to avoid the overhead of having a DMA
map for each of them. Bump the number of hardware descriptors to 128,
and use half as many software descriptors for now.
Some minor cleanups.
- remove DPRINTF(), there is a CTR*() for any of them, and KTR is
far more useful to debug this driver.
- some cleanups; remove some unused code and definitions.
o create a separate tag for each object allocated with bus_dmamem_alloc so
the tag's maxsize is setup appropriately; this reduces memory allocation
for the queue descriptors from 16M to what it should be and also fixes
memory allocation for public key operands
o release bus dma resources on detach so module usage doesn't leak
o remove public key op disable now that bus dma memory allocation is fixed
o collect attach error handling in one place
Sponsored by: Vernier Networks
- 'spec' and 'ver' are attributes of a unit rather than a node.
- Report Phy and Link info separatelly.
- Reorder intialization step in fwohci_reset().
- Fix some bogosity with mixing unit numbers and channels, which would only
work for one instance of the device.
- Use a simpler scheme for input and output queueing.
- Use db_alt_break.
- Separate fc->dev (i.e. fwohci0) and fc->bdev (i.e. firewire0).
- Remove unused firewirebusreg.h.
- Reduce size of descriptor block for asynchronous transmit and
check the number of descriptor when copying from mbuf.
- Skip mbuf whose length is zero. NFS seems passing such mbuf and
some chips generates unrecoverable error.
- Restore pci config registers after resume.
- Reinitialize and start rx buffers after resume.
- Don't reallocate memory in fwohci_db_init() if the dbch is
already initialized.
- Fix typo.
- Some clean up.
positions for the status bits of port a and port b are different. To
avoid needing to know which channel the interrupt handler is working on,
shift the status bits for port a into the port b bit positions, and always
check the port b status bits. This fixes using port b, which I neglected
to test before.
- Remember to update the channel's tty structure from the passed in termios
in the param routine.
- Minor style.
Metricom Ricochet GS modem. Add them here.
# A new umodem appears to be needed to make the sanyo phone work, but that's
# more extensive and will come after coordination.
With a 1 byte transmit fifo, 3 byte receive fifo, and wierd multiplexed I/O
designed for a Z80 cpu, this chip redefines suckage.
Based on the openbsd and netbsd drivers. Only really works as a console,
modem support is not complete since I can't test it.
this was causing filedesc work to be very painful.
In order to make this work split out sigio definitions to thier own header
(sigio.h) which is included from proc.h for the time being.
for the raidctl device.
Select a more conservative default for the permissions for /dev/raidctl
since the operations are performed using ioctl() not read() and write().
Submitted by: kris
Reviewed by: scottl
Use BUS_SPACE_MAXSIZE_32BIT for the parent dma tags, and
(NSEGS - 1) * PAGE_SIZE for the data buffer tags. FreeBSD/sparc64 is
more strict about checking these values that other arches.
were sometimes propagated using M_COPY_PKTHDR which actually did
something between a "move" and a "copy" operation. This is replaced
by M_MOVE_PKTHDR (which copies the pkthdr contents and "removes" it
from the source mbuf) and m_dup_pkthdr which copies the packet
header contents including any m_tag chain. This corrects numerous
problems whereby mbuf tags could be lost during packet manipulations.
These changes also introduce arguments to m_tag_copy and m_tag_copy_chain
to specify if the tag copy work should potentially block. This
introduces an incompatibility with openbsd which we may want to revisit.
Note that move/dup of packet headers does not handle target mbufs
that have a cluster bound to them. We may want to support this;
for now we watch for it with an assert.
Finally, M_COPYFLAGS was updated to include M_FIRSTFRAG|M_LASTFRAG.
Supported by: Vernier Networks
Reviewed by: Robert Watson <rwatson@FreeBSD.org>
work. The interface was gleaned from the Linux driver. Currently only
one RX & one TX buffer are used. Firmware support is not tested so for the
MPI-350 so it is disabled. Signal cache and monitor mode are not supported
yet. Signal cache is not supported since in encapsulation mode ethernet
frames are returned by the chip. LAN monitor mode support will be added
shortly. Thanks to Warner for the MPI-350 card he sent me.
Add support for RSSI map from PR kern/32880 which was incomplete. Enhanced
with the ability to select the cache mode of raw, dbm or per-cent.
Clean up Signal/Noise/Quality structures and units with help from
Marco Molteni.
Change flash to use a malloc'ed buffer when needed.
PR: kern/32880
Submitted by: Douglas S. J. De Couto decouto@pdos.lcs.mit.edu,
Marco Molteni
MFC: 3 weeks
than hard-coded uids and gids.
Switch the device to a group of wheel instead of operator.
Narrow down the permissions on the device to require root privilege
to manipulate the system power state. It may be that we can broaden
access to the device after review of the access control in ACPI.
Submitted by: kris
Reviewed by: takawata
with make_dev(). Use OPERATOR instead of implicit WHEEL to match
other storage devices. Use a mode of 0640 to be consistent
with other storage devices.
Submitted by: kris
Reviewed by: scottl
Remove the setgid bit from the tga device (?).
Synchronize mode with modes used for related frame buffer devices
in MAKEDEV (tga doesn't appear in MAKEDEV).
Submitted by: kris
improves protection consistency with other storage devices (generally
root:operator,660). This driver appears not to have an active
maintainer.
Submitted by: kris
command in case this setting was not saved. Since bandwidth reclamation
(-current only) often results in bus activity continuing to the end
of every frame, most transfers would fail with IOERROR if this
setting is missed.
Reviewed by: n_hibma
MFC after: 1 week
- Fix permission of device node.
fwochi.c, fwohcireg.h
- Detect phy access failure correct way.
- Set root hold-off bit before initiating bus reset.
This should fix the problem with VIA6306.
fwohcivar.h
- Fix over-allocation of array. (fwohcivar.h)
sbp.c
- Return CAM_DEV_NOT_THERE rather than CAM_TID_INVALID to prevent retry.
- Added support for ITR (interrupt throttle register). This feature is available on
adapters based on 82545 and above
- Fixed problem with vlan support when traffic has priority bits set. (kern/45907)
PR: kern/45907
MFC after: 1 week
I/O port range, then we should ignore a resource if it's NOT
a memory range AND NOT an I/O port range.
The OR in the condition caused us to ignore perfectly valid
memory addresses.
While here, remove redundant parenthesis and reindent the
debug print to avoid long lines.
identify themselves as serial cards that it would be desirable to
attach a different driver than sio to. Since we are claiming all
serial cards, this is not possible. Instead, return -100 to indicate
that we're willing to take the card, but still allow other drivers to
attach.
Pointed out by: Maksim Yevmenkin
not < the size of the device. This avoids geom complaints.
Fix a serious bug in the handling of the RS_NO_CLEAR_UA quirk. When we
go and insert the test-unit-ready command the umass_cam_quirk_cb() function
sets the status as if the READ_CAPACITY command suceeded when, in fact, it
did not. This leads to the CAM layer trying to use garbage in the return
buffer and panicing the system (or doing other bad things).
Add a quirk entry for MSYSTEMS DISK-ON-KEY, which is sold under the Sony
brand as a solid state disk-on-key usb device. This device requires
several quirks to work properly.
Note that the disk-on-key device will not work properly until CAM also
gets a quirk entry for it, which has been submitted to the CAM maintainer,
and you may have to temporarily uncomment the DELAY() as well. -current
does not properly wait for devices to power up so you may also have
to temporarily uncomment the DELAY(300000) to make your device work.
A solution must be found to that issue.
MFC after: 3 days
X-MFC note: the quirk support must MFCd before this patch can be
the dataphysend calculation could only possibly work if the virtual buffer
is also physically contiguous. Calculate dataphysend by calculating the
ending virtual address first, then converting to a physical address.
The second bug applies only to NetBSD and OpenBSD and involves the curlen
calculation in the two-contiguous-physical-pages case (which we don't support).
Also cleanup the use of the OHIC_PAGE() macro on dataphysend and add a panic
if len goes negative (meaning we lost the physical page translation
representing the end of the buffer).
IMHO the dataphysend is still bokered since it might be misrepresented
by shared userland page mappings. The whole section needs to be rewritten
to use the virtual address range.
MFC after: 3 days
prototype for trm_detach and freeing all resources.
While I'm there, handle better errors in trm_attach and remove the
PCI_BASE_ADDR0 definition, since it's what PCIR_MAPS is used for.
MFC after: 3 days
