the dependency on caesar which therefore doesn't need to be built by
bootstrap-tools.
Suggested by: des
Previously mentioned by: Peter Jeremy <peter.jeremy@alcatel.com.au>
frames would be handled incorrectly due to bad usage of m_pullup() in
the case where the frame wraps from the end of the receive buffer back
the beginning.
Also, when manually extending small packets to pad them to the minimum
frame length during transmission, zero out the pad area to make some
really paranoid people happy.
needed to access the internals of buffers but not necessarily to use
the VOP. <sys/buf.h> recently grew a bogus dependency on <sys/systm.h>
for the declaration of spl*, and I prefer to fix the synopsis breakage
by removing a wart instead of adding one.
VOP_ABORTOP() went away. at_shutdown() was replaced by undocumented
event handling. Rename remove_dev() here too, and remove the dead
and dead wrong man pages.
takes an int arg and is prototyped in <string.h>. It has the opposite
interface botches to psignal(3) which takes a bogus unsigned arg but is
prototyped in the right place.
This is not the last of the interface problems for strsignal(). We
obtained it from NetBSD, but NetBSD has moved its prototype to
<unistd.h>. strsignal() should return const char *, but it returns
char * for historical reasons. NetBSD declares it as returning
__aconst char, where __aconst is normally empty but can be set to
`const' to give better error checking. glibc-2.1.1 prototypes
strsignal() in <string.h>.
when I made the absence of the clean flag sticky in rev.1.88. This
was a problem main for "mount /". There is no way to mount "/" for
writing without using mount -u (normally implicitly), so after
"mount -f /" of an unclean filesystem, the absence of the clean flag
was sticky forever.
each and every xxx_genassym.c file to seperately define these and
also to promote uniformity and a level of abstraction.
Symbols are created as unsigned long by default and overridable on
a per file basis.
/usr/games on purpose. All tools in /usr/games are built as part of
the tool stages to support building world on machines without games.
This fixes any build problems that have been caused by non-standard
paths and also removes the primary objection for not using absolute
paths.
o Add genassym to the list of cross-tools
o Remove sh hashing work-around, we don't need it anymore
o Clean more directories in WORLDTMP when NOCLEAN is specified
The sh hashing work-around is not needed anymore, because we don't
trigger the bug anymore.
When NOCLEAN is not defined, we wipe out the complete WORLDTMP,
including the object directories of the tools we have built. When
NOCLEAN is defined, we remove anything that we install anyway, which
is usr/bin, usr/games, usr/include, usr/lib and usr/sbin.
- In uhci_intr() check to see if sc->sc_bus.bdev is NULL, and if it is,
ack any pending interrupts and disable them, then return. It is possible
for interrupts to be delivered the moment a handler is set up at attach
time in uhci_pci.c, particularly when attempting to kldload the usb.ko
module after the system is already up. However the driver isn't ready
to field interrupts at that time and certain pointers in the softc
struct aren't initialized yet, and we invariably end up falling off
the end of one of them. The effect is that kldloading the usb module
will panic the system in uhci_intr(). This added sanity check stops
this from happening: I can now kldload the usb.ko module without any
problems and load/attach other USB drivers after it.
Of course the uhci driver has no detach method, but that's another
problem.
- In uhci_run(), set the UHCI_CMD_MAXP bit in the command register to
allow 64-byte packets to be used for full speed bandwidth reclamation.
Certain high speed devices (in this case the ADMtek USB ethernet
adapter) require this bit to be set, otherwise babble errors occur
at the end of large (between 1100 and 1500 byte) transfers. This
should not affect other devices, although supposedly it is less efficient
than the 32-byte setting. Unfortunately, this is a per-bus setting,
not a per-device setting, so we can't just enable it for certain
devices on the USB bus.
