other architectures [1].
While here:
- Remove an unused and commented out include.
- Add a comment describing the file that other copies have.
- Fix the style of the defines and add a comment on what each one is.
Suggested by: [1] alc
sent a SIGABRT when it is loaded as it is too large. This is the smallest
power of two MiB value that allows us to execute clang.
While here wrap it in an #ifndef to be consistent with the other
architectures.
Submitted by: Daisuke Aoyama <aoyama at peach.ne.jp>
Switch eventtimers(9) from using struct bintime to sbintime_t.
Even before this not a single driver really supported full dynamic range of
struct bintime even in theory, not speaking about practical inexpediency.
This change legitimates the status quo and cleans up the code.
Although AM335x TRM states that GPIO_OE register is not used and just
reflects pads configuration in practice it does control pin behavior
and shoiuld be set in addition to pinmux setup
Replace the sub-optimal uma_zone_set_obj() primitive with more modern
uma_zone_reserve_kva(). The new primitive reserves before hand
the necessary KVA space to cater the zone allocations and allocates pages
with ALLOC_NOOBJ. More specifically:
- uma_zone_reserve_kva() does not need an object to cater the backend
allocator.
- uma_zone_reserve_kva() can cater M_WAITOK requests, in order to
serve zones which need to do uma_prealloc() too.
- When possible, uma_zone_reserve_kva() uses directly the direct-mapping
by uma_small_alloc() rather than relying on the KVA / offset
combination.
The removal of the object attribute allows 2 further changes:
1) _vm_object_allocate() becomes static within vm_object.c
2) VM_OBJECT_LOCK_INIT() is removed. This function is replaced by
direct calls to mtx_init() as there is no need to export it anymore
and the calls aren't either homogeneous anymore: there are now small
differences between arguments passed to mtx_init().
Sponsored by: EMC / Isilon storage division
Reviewed by: alc (which also offered almost all the comments)
Tested by: pho, jhb, davide
fact, use the same values here that we use on 32-bit x86 and MIPS. Some
machines were reported to have problems with the more aggressive values.
Reported and tested by: andrew
thread scheduled by interrupt fired after we entered critical section.
None of cpu_sleep() implementations on ARM check sched_runnable() now, so
put the first line of defence here. This mostly fixes unexpectedly long
sleeps in synthetic tests of calloutng code and probably other situations.
seems to cause more problems then previous behavior: it either breaks
initilization sequence in other places or uncovers problems with
high-speed mode timing for SDHCI 3.0
Fix pull-up and pull-down values of gpio.
According to A10 user manual possible pull register
values are 00 Pull-up/down disable, 01 Pull-up, 10 Pull-down.
Approved by: gonzo@
submap. Otherwise, after r246204, the auto-scaling logic in kern_malloc.c
tries to create a kmem submap that consumes the entire kernel map on a
Pandaboard with 1 GB of RAM.
Tested by: gonzo
machine to another. Therefore, VM_MAX_KERNEL_ADDRESS can't be a constant.
Instead, #define it to be a variable, vm_max_kernel_address, just like we
do on sparc64.
Reviewed by: kib
Tested by: ian
SDHCI driver
Suggested by: Daisuke Aoyama
- Set initilization sequence frequency to 8MHz. It should fix Data CRC
errors. Standard requires initialization sequence to be executed
at 400KHz but on this hardware low frequncies seems to cause
Data CRC errors.
Value was derived from analyzing hardware signals after
Raspberry Pi is powered up. Before any data is read though DATA line
adapter's clock frequency is changed to 8MHz.
Modern cards should function fine at 8MHz but for older MMC cards it
can be overriden by setting hw.bcm2835.sdhci.min_freq tunable.
every architecture's busdma_machdep.c. It is done by unifying the
bus_dmamap_load_buffer() routines so that they may be called from MI
code. The MD busdma is then given a chance to do any final processing
in the complete() callback.
The cam changes unify the bus_dmamap_load* handling in cam drivers.
The arm and mips implementations are updated to track virtual
addresses for sync(). Previously this was done in a type specific
way. Now it is done in a generic way by recording the list of
virtuals in the map.
Submitted by: jeff (sponsored by EMC/Isilon)
Reviewed by: kan (previous version), scottl,
mjacob (isp(4), no objections for target mode changes)
Discussed with: ian (arm changes)
Tested by: marius (sparc64), mips (jmallet), isci(4) on x86 (jharris),
amd64 (Fabian Keil <freebsd-listen@fabiankeil.de>)
Major changes:
* Finally tracked down the flow control setting that
seems to have been causing TX stalls and watchdog timeouts
* RX and TX paths now share a lot more code
* TX interrupt is no longer used; we instead GC finished
tx queue entries at the bottom of the start routine.
* TX start now queues fragmented packets directly; it only
invokes defrag() for occasional very fragmented packets.
* "sysctl dev.cpsw" dumps controller statistics and queue counts
* Host Error Interrupt will give extensive debugging information
if the controller chokes on the queued data.
VM_KMEM_SIZE_SCALE specifies which fraction of the available physical
memory, after deduction of the kernel itself and other early statically
allocated memory, can be used for the kmem_map. The kmem_map provides
for all UMA/malloc allocations in KVM space.
Previously ARM was using a fixed kmem_map size of (12*1024*1024) = 12MB
without regard to effectively available memory. This is too small for
recent ARM SoC with more than 128MB of RAM.
For reference a description of others related kmem_map parameters:
VM_KMEM_SIZE default start size of kmem_map if SCALE is
not defined
VM_KMEM_SIZE_MIN hard floor on the kmem_map size
VM_KMEM_SIZE_MAX hard ceiling on the kmem_map size
VM_KMEM_SIZE_SCALE fraction of the available real memory to
be used for the kmem_map, limited by the
MIN and MAX parameters.
Tested by: ian
MFC after: 1 week
In all the routines that loop through a range of virtual addresses, the loop
is controlled by subtracting the cache line size from the total length of the
request. After the subtract, a 'bpl' instruction was used, which branches if
the result of the subtraction is zero or greater, but we need to exit the
loop when the count hits zero. Thus, all the bpl instructions in those loops
have been changed to 'bhi' (branch if greater than zero).
In addition, the two routines that walk through the cache using set-and-index
were correct, but confusing. The loop control for those has been simplified,
just so that it's easier to see by examination that the code is correct.
Routines for other arm architectures and generations still have the bpl
instruction, but compensate for the off-by-one situation by decrementing
the count register by one before entering the loop.
PR: arm/174461
Approved by: cognet (mentor)
This adds support for version 10, revision 01, but it should also work
without changes for the 0901 model, at least until we get drivers for the
two different wifi chips involved.
Many users contributed to and tested the various patchsets floating around
for the past year that have eventually evolved into this checkin, most notably
Richard Neese who provided the bulk of the kernel config file.
Approved by: cognet (mentor)
so that we don't need an empty implementation of it for every Marvell platform
that has no PCI. This allows the removal of the SheevaPlug-specific stub and
config files, and eliminates the need to add similar stubs for future models.
Marvell platforms that do expose PCI are compiled with 'device pci' which
causes the real (non-weak) implementation in dev/fdt/fdt_pci.c to be used.
Approved by: cognet (mentor)
the prior commit. Use essentially the same sprintf() statement for both
formatting and pre-formatting, and use a format string which eliminates the
need for an extra temporary buffer when formatting the name.
Noted by: Christoph Mallon
Pointy hat to: ian
Approved by: cognet (mentor)
interrupt counts and names, by making the names into an array of fixed-length
strings that can be directly indexed. This eliminates extra memory accesses
on every interrupt to increment the counts.
As a side effect, it also fixes a bug that would corrupt the names data
if a name was longer than MAXCOMLEN, which led to incorrect vmstat -i output.
Approved by: cognet (mentor)
ARM EABI syscall calling convention.
The current ABI encodes the syscall number in the instruction. This causes
issues with the thumb mode as it only has 8 bits to encode this value and
we have too many system calls and by using a register will simplify the
code to get the syscall number in the kernel.
With the ARM EABI we reuse the Linux calling convention by storing the
value in r7. Because of this we use both methods to encode the syscall
number in this function.
on Raspberry Pi.
o convert mmap address to physical.
o add FBIOGTYPE ioctl handler - allow to get screen resolution by new
xf86-video-scfb driver.
Originally designed for "Efika MX" project.
Sponsored by: FreeBSD Foundation
- Missing PTE_SYNC in pmap_kremove caused memory corruption
in userland applications
- Fix lack of cache flushes when using special PTEs for zeroing or
copying pages. If there are dirty lines for destination memory
and page later remapped as a non-cached region actual content
might be overwritten by these dirty lines when cache eviction
happens as a result of applying cache eviction policy or because
of wbinv_all call.
- icache sync for new mapping for userland applications.
Tested by: gber
l2_wbinv_range function implementation causes function
fail to flush caches for chip with RTL number 0x7. I failed
to find official PL310 revision with this RTL number
so further research on this matter required.
TX stalls in this driver, I've also had some
time to evaluate the effectiveness of different
watchdog strategies.
This is the latest attempt, which consolidates
all of the watchdog logic in one place and
consistently detects TX stalls and resets within
a couple of seconds.
(as used in AM335x SoC for BeagleBone).
Among other things:
* Watchdog reset doesn't hang the driver.
* Disconnecting cable doesn't hang the driver.
* ifconfig up/down doesn't hang the driver
* Out-of-memory no longer panics the driver.
Known issues:
* Doesn't have good support for fragmented packets
(calls m_defrag() on TX, assumes RX packets are never fragmented)
* Promisc and allmulti still unimplimented
* addmulti and delmulti still unimplemented
* TX queue still stalls (but watchdog now consistently recovers in ~5s)
* No sysctl monitoring
* Only supports port0
* No switch configuration support
* Not tested on anything but BeagleBone
Committed from: BeagleBone
- Add pl310.disable tunable to disable L2 cache altogether. In
order to make sure that it's 100% disabled we use cache event
counters for cache line eviction and read allocate events
and panic if any of these counters increased. This is purely
for debugging purpose
- Direct access DEBUG_CTRL and CTRL might be unavailable in
unsecure mode, so use platform-specific functions for
these registers
- Replace #if 1 with proper erratum numbers
- Add erratum 753970 workaround
- Remove wait function for atomic operations
- Protect cache operations with spin mutex in order to prevent race condition
- Disable instruction cache prefetch and make sure data cache
prefetch is enabled in OMAP4-specific intialization
Interrupts must be disabled while handling a partial cache line flush,
as otherwise the interrupt handling code may modify data in the non-DMA
part of the cache line while we have it stashed away in the temporary
stack buffer, then we end up restoring a stale value.
PR: 160431
Submitted by: Ian Lepore
Basically it's replica of VersatilePB code which is replica of XBox FB
code. All of them are linear framebuffers and should have common bits
moved to reusable framework.
- Disable interrupt when updating compare value in order to
make this operation atomical
- Increase minimum period for event timer. Systimer on BCM2835
is compare timer, so if minimum period is too small it might
be less then fraction of time between "read current value" and
"set compare timer" operations. It means that when timer is armed
actual counter value is more then compare value and it will take
whole cycle (~32sec for 1MHz timer) to fire interrupt.
Submitted by: Daisuke Aoyama <aoyama at peach.ne.jp>
allocate a map or mapping resources. That seems to imply that any memory
allocations it does must use M_NOWAIT and check for NULL.
Submitted by: Ian Lepore <freebsd@damnhippie.dyndns.org>
