having the PCI-ISA bridge driver depend on both pci and isa.
- Have the PCI-EISA bridge driver depend on both pci and eisa as well.
- Make acpi_isab.c depend on acpi and isa.
Submitted by: Marius Strobl <marius@alchemy.franken.de> (1,2)
ACPI nodes with the plug and play ID's defined for a "Generic ISA Bus
Device" as defined in section 10.7 of the ACPI 2.0 specification. This
gives machines like the Libretto that contain a fake ISA bus that is not
connected via a PCI-ISA bridge an ISA bus for ISA devices to attach to.
Tested by: markm
with a new implementation that has a mostly reentrant "addchar"
routine, supports multiple message buffers in the kernel, and hides
the implementation details from callers.
The new code uses a kind of sequence number to represend the current
read and write positions in the buffer. This approach (suggested
mainly by bde) permits the read and write pointers to be maintained
separately, which reduces the number of atomic operations that are
required. The "mostly reentrant" above refers to the way that while
it is now always safe to have any number of concurrent writers,
readers could see the message buffer after a writer has advanced
the pointers but before it has witten the new character.
Discussed on: freebsd-arch
redundant paths to the same device.
This class reacts to a label in the first sector of the device,
which is created the following way:
# "0123456789abcdef012345..."
# "<----magic-----><-id-...>
echo "GEOM::FOX someid" | dd of=/dev/da0 conv=sync
NB: Since the fact that multiple disk devices are in fact the same
device is not known to GEOM, the geom taste/spoil process cannot
fully catch all corner cases and this module can therefore be
confused if you do the right wrong things.
NB: The disk level drivers need to do the right thing for this to
be useful, and that is not by definition currently the case.
toggle several media options (sonet/sdh, for example) with ifconfig and
to see the carrier state in ifconfig's output. It gives also read/write
access (given the right privilegs) to the S/Uni registers to user space
programs.
ethernet controller. The driver has been tested with the LinkSys
USB200M adapter. I know for a fact that there are other devices out
there with this chip but don't have all the USB vendor/device IDs.
Note: I'm not sure if this will force the driver to end up in the
install kernel image or not. Special magic needs to be done to exclude
it to keep the boot floppies from bloating again, someone please
advise.
monitors the entropy data harvested by crypto drivers to verify it complies
with FIPS 140-2. If data fails any test then the driver discards it and
commences continuous testing of harvested data until it is deemed ok.
Results are collected in a statistics block and, optionally, reported on
the console. In normal use the overhead associated with this driver is
not noticeable.
Note that drivers must (currently) be compiled specially to enable use.
Obtained from: original code by Jason L. Wright
included in XFree86 4.3, but includes some fixes. Notable changes include
Radeon 8500-9100 support, PCI Radeon/Rage 128 support, transform & lighting
support for Radeons, and vblank syncing support for r128, radeon, and mga.
The gamma driver was removed due to lack of any users.
drain routines are done by swi_net, which allows for better queue control
at some future point. Packets may also be directly dispatched to a netisr
instead of queued, this may be of interest at some installations, but
currently defaults to off.
Reviewed by: hsu, silby, jayanth, sam
Sponsored by: DARPA, NAI Labs
permit users and groups to bind ports for TCP or UDP, and is intended
to be combined with the recently committed support for
net.inet.ip.portrange.reservedhigh. The policy is twiddled using
sysctl(8). To use this module, you will need to compile in MAC
support, and probably set reservedhigh to 0, then twiddle
security.mac.portacl.rules to set things as desired. This policy
module only restricts ports explicitly bound using bind(), not
implicitly bound ports where the port number is selected by the
IP stack. It appears to work properly in my local configuration,
but needs more broad testing.
A sample policy might be:
# sysctl security.mac.portacl.rules="uid:425:tcp:80,uid:425:tcp:79"
This permits uid 425 to bind TCP sockets to ports 79 and 80. Currently
no distinction is made for incoming vs. outgoing ports with TCP,
although that would probably be easy to add.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
time and there's no indication that it will improve anytime soon.
By removing support for SimOS it is possible to build LINT on
Alpha, which is considered more important at the moment.
Not objected to on: alpha@
type M_STRING, now defined in malloc.h. Useful when string parsing
must occur using the kernel strsep() and we want to avoid toasting
the source string.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
This moves all chipset specific code to a new file 'ata-chipset.c'.
Extensive use of tables and pointers to avoid having the same switch
on chipset type in several places, and to allow substituting various
functions for different HW arch needs.
Added PIO mode setup and all DMA modes.
Support for all known SiS chipsets. Thanks to Christoph Kukulies for
sponsoring a nice ASUS P4S8X SiS648 based board for this work!
Tested on: i386, PC98, alpha and sparc64
for the agp module, and add agp to the list of modules to compile for alpha.
Add an alpha_mb() to agp_flush_cache for alpha -- it's not correct but may
improve the situation, and it's what linux and NetBSD do.
Insted of embedding a struct g_stat in consumers and providers, merely
include a pointer.
Remove a couple of <sys/time.h> includes now unneeded.
Add a special allocator for struct g_stat. This allocator will allocate
entire pages and hand out g_stat functions from there. The "id" field
indicates free/used status.
Add "/dev/geom.stats" device driver whic exports the pages from the
allocator to userland with mmap(2) in read-only mode.
This mmap(2) interface should be considered a non-public interface and
the functions in libgeom (not yet committed) should be used to access
the statistics data.
