Aaron Campbell <aaron@cs.dal.ca>.
Use SHIFT-PgUp and SHIFT-PgDn to scroll back and forward.
Aarons original code was enhanced to have a separate scrollbuffer
for every virtual terminal and to preserve the screen contents
when switching screen sizes.
The scrollbuffer size is currently fixed at 8 pages but this
will be made configurable through the use of scon(1) in the
near future.
For pcvt_kbd.h, a longstanding compiler warning was fixed by
using excessive backetizing of the key2ascii[] table.
to be created at init time. The unit devices are created at
ctor when new instances are created and bound and destroyed
when that instance is closed. As such, there is just s single
static control dev_t for this driver (the per-unit dev_t's are
still in the softc).
When we have decommissionable periph drivers, a destroy_device
on the control device will have to called.
resulted in vastly optimistic offset values reported to userland
(typically a factor 40+ too small). Apart from that, the code had
two sign-bugs.
Apply the hardpps() phase with the right sign with a simply
scaling by integration interval. (This may be too stiff at
long integration intervals, see below).
Allow pps_shiftmax to be reduced again.
Before this, the phase lock in hardpps() were broken, but due to
two bugs mostly cancelling out, it would end up basically working
with a large stochastic component. Now it behaves as one would
expect: smooth and quiet.
It seems that pps_shiftmax above 7..9 somewhere makes the phaselock
too weak to hold onto random walk phase errors from a HP-105 OCXO,
which basically means that it is too weak for real-life use with
such integration times. This is yet to be resolved.
Submitted to: Prof. Dave "NTP" Mills.
Tested by: Terje Mathisen <Terje.Mathisen@hda.hydro.com>
probes are at the 'chip' level and will get overridden by pcic_p if it is
compiled in. It's still nice to get the better probe message if it's not...
Requested by: imp
for our use. Use the same search order for BIOS memory size functions
as the kernel will later use.
Allow the loader to use all of the detected physical memory (this will
greatly help people trying to load enormous memory disk images).
More correctly handle running out of memory when loading an object.
Use the end of base memory for the top of the heap, rather than
blindly hoping that there is 384k left.
Add copyrights to a couple of files I forgot.
because bsd.kmod.mk is usually out of sync with kernel source. However
bsd.kmod.mk has to be updated now because of the _KERNEL change so there
is no need to keep this (pre-repo copy) version around.
is an application space macro and the applications are supposed to be free
to use it as they please (but cannot). This is consistant with the other
BSD's who made this change quite some time ago. More commits to come.
is an application space macro and the applications are supposed to be free
to use it as they please (but cannot). This is consistant with the other
BSD's who made this change quite some time ago. More commits to come.
desperation measure in low-memory situations), walk the tcpbs and
flush the reassembly queues.
This behaviour is currently controlled by the debug.do_tcpdrain sysctl
(defaults to on).
Submitted by: Bosko Milekic <bmilekic@dsuper.net>
Reviewed by: wollman
5in HD 2 heads, 77 cylinders, 8 sectors/track, 1024 bytes/sector
5/3.5in DD 2 heads, 80 cylinders, 8 sectors/track, 512 bytes/sector
Meanings of the rogrammer-readeble fd name were explained by Brian
Fundakowski Feldman and Peter Wemm in hackers list and NOKUBI
Hirotaka.
Reviewed by: nyan
swap_pager.c and related commits.
Essentially swap_pager.c is backed out to before the changes, but
swapdev_vp is converted into a real vnode with just VOP_STRATEGY().
It no longer abuses specfs vnops and no longer needs a dev_t and
/dev/drum (or /dev/swapdev) for the intermediate layer.
This essentially restores the vnode interface as the interface to the
bottom of the swap pager, and vm_swap.c provides a clean vnode interface.
This will need to be revisited when we swap to files (vnodes) - which
is the other reason for keeping the vnode interface between the swap pager
and the swap devices.
OK'ed by: dillon
USB ethernet chip. Adapters that use this chip include the LinkSys
USB100TX. There are a few others, but I'm not certain of their
availability in the U.S. I used an ADMtek eval board for development.
Note that while the ADMtek chip is a 100Mbps device, you can't really
get 100Mbps speeds over USB. Regardless, this driver uses miibus to
allow speed and duplex mode selection as well as autonegotiation.
Building and kldloading the driver as a module is also supported.
Note that in order to make this driver work, I had to make what some
may consider an ugly hack to sys/dev/usb/usbdi.c. The usbd_transfer()
function will use tsleep() for synchronous transfers that don't complete
right away. This is a problem since there are times when we need to
do sync transfers from an interrupt context (i.e. when reading registers
from the MAC via the control endpoint), where tsleep() us a no-no.
My hack allows the driver to have the code poll for transfer completion
subject to the xfer->timeout timeout rather that calling tsleep().
This hack is controlled by a quirk entry and is only enabled for the
ADMtek device.
Now, I'm sure there are a few of you out there ready to jump on me
and suggest some other approach that doesn't involve a busy wait. The
only solution that might work is to handle the interrupts in a kernel
thread, where you may have something resembling a process context that
makes it okay to tsleep(). This is lovely, except we don't have any
mechanism like that now, and I'm not about to implement such a thing
myself since it's beyond the scope of driver development. (Translation:
I'll be damned if I know how to do it.) If FreeBSD ever aquires such
a mechanism, I'll be glad to revisit the driver to take advantage of
it. In the meantime, I settled for what I perceived to be the solution
that involved the least amount of code changes. In general, the hit
is pretty light.
Also note that my only USB test box has a UHCI controller: I haven't
I don't have a machine with an OHCI controller available.
Highlights:
- Updated usb_quirks.* to add UQ_NO_TSLEEP quirk for ADMtek part.
- Updated usbdevs and regenerated generated files
- Updated HARDWARE.TXT and RELNOTES.TXT files
- Updated sysinstall/device.c and userconfig.c
- Updated kernel configs -- device aue0 is commented out by default
- Updated /sys/conf/files
- Added new kld module directory
devices.
o Return ENXIO from sn_isa_probe
o Fix SN_DEBUG printf
o Use IFQ_MAXLEN rather than 8
I'll fix the isa probe when I get access to a real isa attachment
device to test against here in a few days.
Overly agressive snagging behavior noticed by: phk
Now you can build a kernel which support IPsec message authentication
but don't support message encryption, by defining IPSEC in your kernel
config file and not defining IPSEC_ESP.
rev.1.168 should have been committed concurrently:
Fixed some style bugs (always use precisely 1 space after `:' in
dependency specifications).
Removed bogus dependency of ${FULLKERNEL} on ${BEFORE_DEPEND}.
Reminded by: peter
Changed the type used to represent the user stack pointer from `long *'
to `register_t *'. This fixes bugs like misplacement of argc and argv
on the user stack on i386's with 64-bit longs. We still use longs to
represent "words" like argc and argv, and assume that they are on the
stack (and that there is stack). The suword() and fuword() families
should also use register_t.
to `register_t *'. This fixes bugs like misplacement of argc and argv
on the user stack on i386's with 64-bit longs. We still use longs to
represent "words" like argc and argv, and assume that they are on the
stack (and that there is stack). The suword() and fuword() families
should also use register_t.
register_t, so pointers to it must be passed around as `register_t *',
not as `int *'. The type mismatches were non-benign on alphas, but
the broken code is normally only configured by LINT.
