permit users and groups to bind ports for TCP or UDP, and is intended
to be combined with the recently committed support for
net.inet.ip.portrange.reservedhigh. The policy is twiddled using
sysctl(8). To use this module, you will need to compile in MAC
support, and probably set reservedhigh to 0, then twiddle
security.mac.portacl.rules to set things as desired. This policy
module only restricts ports explicitly bound using bind(), not
implicitly bound ports where the port number is selected by the
IP stack. It appears to work properly in my local configuration,
but needs more broad testing.
A sample policy might be:
# sysctl security.mac.portacl.rules="uid:425:tcp:80,uid:425:tcp:79"
This permits uid 425 to bind TCP sockets to ports 79 and 80. Currently
no distinction is made for incoming vs. outgoing ports with TCP,
although that would probably be easy to add.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
for the agp module, and add agp to the list of modules to compile for alpha.
Add an alpha_mb() to agp_flush_cache for alpha -- it's not correct but may
improve the situation, and it's what linux and NetBSD do.
Interface (SMAPI) BIOS, which is present on some IBM
Thinkpad models (560, 600, 770 to name a few.)
The SMAPI BIOS provides access to System Information,
System Configuration, and Power Management.
module dependency system rely on linker behaviour that is machine dependent
and not part of the elf spec, and only work by accident on other platforms.
Approved by: re
the supported platforms. We build it into GENERIC, and it is currently
listed on the supported module list for drivers.conf on i386, which
breaks the release build. This may fix the release build for RC1 on
i386.
Conspiracy of: re
is a compiler tool and needs to be compiled by the host compiler. I've
tested this in i386->sparc cross-build, 4.7->current upgrade, normal
buildkernel target, and normal /sys/i386/compile/GENERIC configurations.
Submitted by: ru
This policy can be loaded dynamically, and assigns each process a
partition number, as well as permitting processes to operate outside
the partition. Processes contained in a partition can only "see"
processes inside the same partition, so it's a little like jail.
The partition of a user can be set using the label mechanisms in
login.conf. This sample policy is a good starting point for developers
wanting to learn about how to produce labeled policies, as it labels
only one kernel object, the process credential.
PR:
Submitted by:
Reviewed by:
Approved by:
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
- Add detach support to the driver so that you can kldunload the module.
Note that currently rc_detach() fails to detach a unit if any of its
child devices are open, thus a kldunload will fail if any of the tty
devices are currently open.
- sys/i386/isa/ic/cd180.h was moved to sys/dev/ic/cd180.h as part of
this change.
Requested by: rwatson
Tested by: rwatson
Option 'P1003_1B_SEMAPHORES' to compile them in, or load the "sem" module
to activate them.
Have kern/makesyscalls.sh emit an include for sys/_semaphore.h into sysproto.h
to pull in the typedef for semid_t.
Add the syscalls to the syscall table as module stubs.
build on, let alone actually do some useful work on real hardware.
Namely, put it in i386/pc98. There is no bus_dma.h on the other architecures,
tra la.
kernel access control.
Hook up various policy modules to the kernel build.
Note that a number of these modules require futher entry point commits
in the remainder of the kernel to become fully functional, but enough
of the pieces are in place to allow experimentation.
Note also that it would be desirable to not build the mac_*.ko modules
if 'options MAC' is not defined in the kernel configuration, because
the resulting modules are not useful without the kernel option. There
doesn't appear to be precedent for a way to do this -- for example,
we allow ipfw.ko to be built even if 'options NETINET' isn't defined.
Suggests welcomed on the "best" way to do this.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, NAI Labs
o Make the cam, cd9660 lomac and sound modules i386 and alpha
specific due to link problems (@gprel relocation when @ltoff
is required). Once resolved, these can be moved back to the
generic list.
o Build linprocfs only on those architectures that have the
linux module.
o Make the sppp module i386 and alpha specific due to compile
problems (pointers as switch cases). Once resolved, this can
be moved back to the generic list.
o Build all i386 specific modules, with the exception of those
mentioned above as being moved from the generic list to the
i386 list and those with dependencies on the linux module (aac)
or i386 dependent (ar, apm, atspeaker, fpu, gnufpu, ibcs2,
linux, ncv, nsp, netgraph, oltr, pecoff, s3, sbni, stg and
vesa).
o Don't build acpi as a module yet. It most be ported first.
Once ported, it can be added to the ia64 list.
o Don't build ipfilter yet due to compile errors (osreldate.h
not found).
- Add stubs for EISA and SBUS cards.
(VME, FutureBUS, and TurboChannel stubs not provided.)
- Add infrastructure to build driver and bus front-end modules.
prior ICP Vortex models. This driver was developed by Achim Leubner
of Intel (previously with ICP Vortex) and Boji Kannanthanam of Intel.
Submitted by: "Kannanthanam, Boji T" <boji.t.kannanthanam@intel.com>
MFC after: 2 weeks
Remove the explicit call to aio_proc_rundown() from exit1(), instead AIO
will use at_exit(9).
Add functions at_exec(9), rm_at_exec(9) which function nearly the
same as at_exec(9) and rm_at_exec(9), these functions are called
on behalf of modules at the time of execve(2) after the image
activator has run.
Use a modified version of tegge's suggestion via at_exec(9) to close
an exploitable race in AIO.
Fix SYSCALL_MODULE_HELPER such that it's archetecuterally neutral,
the problem was that one had to pass it a paramater indicating the
number of arguments which were actually the number of "int". Fix
it by using an inline version of the AS macro against the syscall
arguments. (AS should be available globally but we'll get to that
later.)
Add a primative system for dynamically adding kqueue ops, it's really
not as sophisticated as it should be, but I'll discuss with jlemon when
he's around.
Alpha can verify that it compiles fine there, too, this should be moved
to the MI section (or that problem fixed); I've only had x86 hardware to
est with.
Sponsored by: DARPA, NAI Labs (CBOSS project)
ethernet controllers. This adds support for the 3Com 3c996-T, the
SysKonnect SK-9D21 and SK-9D41, and the built-in gigE NICs on
Dell PowerEdge 2550 servers. The latter configuration hauls ass:
preliminary measurements show TCP speeds of over 900Mbps using
only normal size frames.
TCP/IP checksum offload, jumbo frames and VLAN tag insertion/stripping
are supported, as well as interrupt moderation.
Still need to fix autonegotiation support for 1000baseSX NICs, but
beyond that, driver is pretty solid.
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
blown over by the Hurricane and had a house dropped on you by the Tornado.
Now it's time to have your parade rained on by... the Typhoon!
This commit adds driver support for 3Com 3cR990 10/100 ethernet
adapters based on the Typhoon I and Typhoon II chipsets. This is actually
a port of the OpenBSD driver with many hacks by me.
No Virginia, there isn't any support for the hardware crypto yet. However
there is support for TCP/IP checksum offload and VLANs.
Special thanks go to Jason Wright, Aaron Campbell and Theo de Raadt for
squeezing enough info out of 3Com to get this written, and for doing
most of the hard work.
Manual page is included. Compiled as a module and included in GENERIC.
a KLD. Still doesn't work well except in the PCMCIA case (now if only
pccardd(8) could load and unload drivers dynamically...). Mainly, it
tries to find fdc0 on the PCI bus for whatever obscure reasons, but i
need someone who understands driver(9) to fix this. However, it's at least
already better than before, and i'm tired of maintaining too many private
changes in my tree, given the large patches bde submitted. :)
Idea of a KLD triggered by: Michael Reifenberger <root@nihil.plaut.de>
could only get a chance of testing it under 4.3, but together with the
if_oltr.c fixes at least it seems to work now. If someone has the chance
to test this under -current, please do.
Unfortunaltey, the TR code itself (if_iso88025subr.c) is not written
in a way that would allow to make a seaparate KLD out of it. By now,
just link it directly into the oltr KLD since it's probably the POLA
to be able to load the TR code together with the only TR hardware
driver we've got by now.
I've got one single unexplained panic (in doreti_switch or somewhere
there, calling a 0xc1XXXXXX address that did no longer belong to the
kernel at all) after unloading the modules once, thus i don't propose
a MFC of this module despite my testing has been done solely on 4.3,
unless someone is really going to test this stuff in -current.
gigabit ethernet controller chip. This device is used on some
fiber optic gigE cards from SMC, D-Link and Addtron. Jumbograms and
TCP/IP checksum offload on receive are supported. Hardware VLAN
filtering is not, because it doesn't play well with our existing
VLAN code. Also add manual page.
There is a 4.x version of this driver available at
http://www.freebsd.org/~wpaul/Level1/4.x if anyone feels adventurous
and wants to test it. I still need to do performance testing and
tuning with this device.
(For my next trick, I will make the 3Com 3cR990 sit up and beg.)
systems were repo-copied from sys/miscfs to sys/fs.
- Renamed the following file systems and their modules:
fdesc -> fdescfs, portal -> portalfs, union -> unionfs.
- Renamed corresponding kernel options:
FDESC -> FDESCFS, PORTAL -> PORTALFS, UNION -> UNIONFS.
- Install header files for the above file systems.
- Removed bogus -I${.CURDIR}/../../sys CFLAGS from userland
Makefiles.
and DP83821 gigabit ethernet MAC chips and the NatSemi DP83861 10/100/1000
copper PHY. There are a whole bunch of very low cost cards available with
this chipset selling for $150USD or less. This includes the SMC9462TX,
D-Link DGE-500T, Asante GigaNIX 1000TA and 1000TPC, and a couple cards
from Addtron.
This chip supports TCP/IP checksum offload, VLAN tagging/insertion.
2048-bit multicast filter, jumbograms and has 8K TX and 32K RX FIFOs.
I have not done serious performance testing with this driver. I know
it works, and I want it under CVS control so I can keep tabs on it.
Note that there's no serious mutex stuff in here yet either: I need
to talk more with jhb to figure out the right way to do this. That
said, I don't think there will be any problems.
This driver should also work on the alpha. It's not turned on in
GENERIC.
This driver supports PCI Xr-based and ISA Xem Digiboard cards.
dgm will go away soon if there are no problems reported. For now,
configuring dgm into your kernel warns that you should be using
digi. This driver is probably close to supporting Xi, Xe and Xeve
cards, but I wouldn't expect them to work properly (hardware
donations welcome).
The digi_* pseudo-drivers are not drivers themselves but contain
the BIOS and FEP/OS binaries for various digiboard cards and are
auto-loaded and auto-unloaded by the digi driver at initialisation
time. They *may* be configured into the kernel, but waste a lot
of space if they are. They're intended to be left as modules.
The digictl program is (mainly) used to re-initialise cards that
have external port modules attached such as the PC/Xem.
the video switch by another. Exactly as VESA does on top of VGA.
It adds linear framebuffer to S3 VESA 1.2 cards.
Obtained from: The original S3 ISA code comes from
Peter Horton <pdh@colonel-panic.com>
Add detach routine and turn driver into a module so it can be loaded
and unloaded. Also take a stab at implementing multicast packet
reception so that this NIC will work with IPv6. Promiscuous mode
doesn't seem to work, but I'm not sure why. It works well enough that
I can run dhclient on it and put it on the office network though.
Also ripped out spl stuff and replaced it with mutexes.
now in dirs called sys/*/random/ instead of sys/*/randomdev/*.
Introduce blocking, but only at startup; the random device will
block until the first reseed happens to prevent clients from
using untrustworthy output.
Provide a read_random() call for the rest of the kernel so that
the entropy device does not need to be present. This means that
things like IPX no longer need to have "device random" hardcoded
into thir kernel config. The downside is that read_random() will
provide very poor output until the entropy device is loaded and
reseeded. It is recommended that developers do NOT use the
read_random() call; instead, they should use arc4random() which
internally uses read_random().
Clean up the mutex and locking code a bit; this makes it possible
to unload the module again.
support which use National Semiconductor DP8393X (SONIC) as ethernet
controller. Currently, this driver is used on only PC-98.
Submitted by: Motomichi Matsuzaki <mzaki@e-mail.ne.jp>
Obtained from: NetBSD/pc98
Previously, these cards were supported by the lnc driver (and they
still are, but the pcn driver will claim them first), which is fine
except the lnc driver runs them in 16-bit LANCE compatibility mode.
The pcn driver runs these chips in 32-bit mode and uses the RX alignment
feature to achieve zero-copy receive. (Which puts it in the same
class as the xl, fxp and tl chipsets.) This driver is also MI, so it
will work on the x86 and alpha platforms. (The lnc driver is still
needed to support non-PCI cards. At some point, I'll need to newbusify
it so that it too will me MI.)
The Am79c978 HomePNA adapter is also supported.
This provides support for the Adaptec SCSI RAID controller family,
as well as the DPT SmartRAID V and VI families.
The driver will be maintained by Mark and Adaptec, and any changes
should be referred to the MAINTAINER.
shouldn't be built by default. pcic and pccard are going to go
through some changes and I'll not be testing them on the alpha so I
don't want to break them for the FreeBSD/alpha folks.
Make the umass driver depend on this module.
Makes it possible to compile the kernel without SCSI support and load it
when for example a USB floppy is conencted.
be a permanent rule, because this device may eventually be deemed
"effectively compulsory", and built by default directly into the
kernel. For the moment, however, this is useful for debugging and
development.
Reviewed by: dfr
accept filters are now loadable as well as able to be compiled into
the kernel.
two accept filters are provided, one that returns sockets when data
arrives the other when an http request is completed (doesn't work
with 0.9 requests)
Reviewed by: jmg
2. Newbusify the driver.
3. Build as a module.
4. Use correct minor numbers when creating device files.
5. Correctly lock control characters.
6. Return ENXIO when device not configured.
Submitted by: Tor Egge <Tor.Egge@fast.no>
7. Fix the baud_table.
Submitted by: Elliot Dierksen <ebd@oau.org>
Note:
- the old driver still lives in src/sys/i386/isa, so that you can
revert to it if something goes wrong.
- The module does not detach very well. Attaching works fine.
are two supported chips, the NetChip 1080 (only prototypes available)
and the EzLink cable. Any other cable should be supported however as they
are all very much alike (there is a difference between them wrt
performance).
It uses Netgraph.
This driver was mostly written by Doug Ambrisko and Julian Elischer and
I would like to thank Whistle for yet another contribution. And my
aplogies to them for me sitting on the driver for so long (2 months).
Also, many thanks to Reid Augustin from NetChip for providing me with a
prototype of their 1080 chip.
Be aware of the fact that this driver is very immature and has only been
tested very lightly. If someone feels like learning about Netgraph however
this is an excellent driver to start playing with.
vintage system, well before the ppbus changes. When I called it an
"example" module, I meant as an example for the rest of the ppbus client
drivers, not that it was worthless. I'll mail my 5.8MB world.log to
anybody who doesn't believe me.
Wrongly accused by: obrien
NICs. (Finally!) The PCMCIA, ISA and PCI varieties are all supported,
though only the ISA and PCI ones will work on the alpha for now.
PCCARD, ISA and PCI attachments are all provided. Also provided an
ancontrol(8) utility for configuring the NIC, man pages, and updated
pccard.conf.sample. ISA cards are supported in both ISA PnP and hard-wired
mode, although you must configure the kernel explicitly to support the
hardwired mode since you have to know the I/O address and port ahead
of time.
Special thanks to Doug Ambrisko for doing the initial newbus hackery
and getting it to work in infrastructure mode.
USB-EL1202A chipset. Between this and the other two drivers, we should
have support for pretty much every USB ethernet adapter on the market.
The only other USB chip that I know of is the SMC USB97C196, and right
now I don't know of any adapters that use it (including the ones made
by SMC :/ ).
Note that the CATC chip supports a nifty feature: read and write combining.
This allows multiple ethernet packets to be transfered in a single USB
bulk in/out transaction. However I'm again having trouble with large
bulk in transfers like I did with the ADMtek chip, which leads me to
believe that our USB stack needs some work before we can really make
use of this feature. When/if things improve, I intend to revisit the
aue and cue drivers. For now, I've lost enough sanity points.
Kawasaki LSI KL5KUSB101B chip, including the LinkSys USB10T, the
Entrega NET-USB-E45, the Peracom USB Ethernet Adapter, the 3Com
3c19250 and the ADS Technologies USB-10BT. This device is 10mbs
half-duplex only, so there's miibus or ifmedia support. This device
also requires firmware to be loaded into it, however KLSI allows
redistribution of the firmware images (I specifically asked about
this; they said it was ok).
Special thanks to Annelise Anderson for getting me in touch with
KLSI (eventually) and thanks to KLSI for providing the necessary
programming info.
Highlights:
- Add driver files to /sys/dev/usb
- update usbdevs and regenerate attendate files
- update usb_quirks.c
- Update HARDWARE.TXT and RELNOTES.TXT for i386 and alpha
- Update LINT, GENERIC and others for i386, alpha and pc98
- Add man page
- Add module
- Update sysinstall and userconfig.c
USB ethernet chip. Adapters that use this chip include the LinkSys
USB100TX. There are a few others, but I'm not certain of their
availability in the U.S. I used an ADMtek eval board for development.
Note that while the ADMtek chip is a 100Mbps device, you can't really
get 100Mbps speeds over USB. Regardless, this driver uses miibus to
allow speed and duplex mode selection as well as autonegotiation.
Building and kldloading the driver as a module is also supported.
Note that in order to make this driver work, I had to make what some
may consider an ugly hack to sys/dev/usb/usbdi.c. The usbd_transfer()
function will use tsleep() for synchronous transfers that don't complete
right away. This is a problem since there are times when we need to
do sync transfers from an interrupt context (i.e. when reading registers
from the MAC via the control endpoint), where tsleep() us a no-no.
My hack allows the driver to have the code poll for transfer completion
subject to the xfer->timeout timeout rather that calling tsleep().
This hack is controlled by a quirk entry and is only enabled for the
ADMtek device.
Now, I'm sure there are a few of you out there ready to jump on me
and suggest some other approach that doesn't involve a busy wait. The
only solution that might work is to handle the interrupts in a kernel
thread, where you may have something resembling a process context that
makes it okay to tsleep(). This is lovely, except we don't have any
mechanism like that now, and I'm not about to implement such a thing
myself since it's beyond the scope of driver development. (Translation:
I'll be damned if I know how to do it.) If FreeBSD ever aquires such
a mechanism, I'll be glad to revisit the driver to take advantage of
it. In the meantime, I settled for what I perceived to be the solution
that involved the least amount of code changes. In general, the hit
is pretty light.
Also note that my only USB test box has a UHCI controller: I haven't
I don't have a machine with an OHCI controller available.
Highlights:
- Updated usb_quirks.* to add UQ_NO_TSLEEP quirk for ADMtek part.
- Updated usbdevs and regenerated generated files
- Updated HARDWARE.TXT and RELNOTES.TXT files
- Updated sysinstall/device.c and userconfig.c
- Updated kernel configs -- device aue0 is commented out by default
- Updated /sys/conf/files
- Added new kld module directory
which it replaces. The new driver supports all of the chips supported
by the ones it replaces, as well as many DEC/Intel 21143 10/100 cards.
This also completes my quest to convert things to miibus and add
Alpha support.
- Convert to new bus attachment scheme. Thanks to Blaz Zupan for doing
the initial work here. One thing I changed was to have the attach
and detach routines work like the PCI drivers, which means that in
theory you should be able to load and unload the driver like the PCI
NIC drivers, however the pccard support for this hasn't settled down
yet so it doesn't quite work. Once the pccard work is done, I'll have
to revisit this.
- Add device wi0 to PCCARD. If we're lucky, people should be able to
install via their WaveLAN cards now.
- Add support for signal strength caching. The wicontrol utility has
also been updated to allow zeroing and displaying the signal strength
cache.
- Add a /sys/modules/wi directory and fix a Makefile to builf if_wi.ko.
Currently this module is only built for the i386 platform, though once
the pccard stuff is done it should be able to work on the alpha too.
(Theoretically you should be able to plug one of the WaveLAN/IEEE ISA
cards into an alpha with an ISA slot, but we'll see how that turns out.
- Update LINT to use only device wi0. There is no true ISA version of
the WaveLAN/IEEE so we'll never use an ISA attachment.
- Update files.i386 so that if_wi is dependent on card.
Been in production for 3 years now. Gives Instant Frame relay to if_sr
and if_ar drivers, and PPPOE support soon. See:
ftp://ftp.whistle.com/pub/archie/netgraph/index.html
for on-line manual pages.
Reviewed by: Doug Rabson (dfr@freebsd.org)
Obtained from: Whistle CVS tree
for the AN985 "Centaur" chip, which is apparently the next genetation
of the "Comet." The AN985 is also a tulip clone and is similar to the
AL981 except that it uses a 99C66 EEPROM and a serial MII interface
(instead of direct access to the PHY registers).
Also updated various documentation to mention the AN985 and created
a loadable module.
I don't think there are any cards that use this chip on the market yet:
the datasheet I got from ADMtek has boxes with big X's in them where the
diagrams should be, and the sample boards I got have chips without any
artwork on them.
the Davicom DM9100 and DM9102 chipsets, including the Jaton Corporation
XPressNet. Datasheet is available from www.davicom8.com.
The DM910x chips are still more tulip clones. The API is reproduced
pretty faithfully, unfortunately the performance is pretty bad. The
transmitter seems to have a lot of problems DMAing multi-fragment
packets. The only way to make it work reliably is to coalesce transmitted
packets into a single contiguous buffer. The Linux driver (written by
Davicom) actually does something similar to this. I can't recomment this
NIC as anything more than a "connectivity solution."
This driver uses newbus and miibus and is supported on both i386
and alpha platforms.
SiS 900 and SiS 7016 PCI fast ethernet chipsets. Full manuals for the
SiS chips can be found at www.sis.com.tw.
This is a fairly simple chipset. The receiver uses a 128-bit multicast
hash table and single perfect entry for the station address. Transmit and
receive DMA and FIFO thresholds are easily tuneable. Documentation is
pretty decent and performance is not bad, even on my crufty 486. This
driver uses newbus and miibus and is supported on both the i386 and
alpha architectures.
PCI fast ethernet controller. Currently, the only card I know that uses
this chip is the D-Link DFE-550TX. (Don't ask me where to buy these: the
only cards I have are samples sent to me by D-Link.)
This driver is the first to make use of the miibus code once I'm sure
it all works together nicely, I'll start converting the other drivers.
The Sundance chip is a clone of the 3Com 3c90x Etherlink XL design
only with its own register layout. Support is provided for ifmedia,
hardware multicast filtering, bridging and promiscuous mode.
MII-compliant PHY drivers. Many 10/100 ethernet NICs available today
either use an MII transceiver or have built-in transceivers that can
be programmed using an MII interface. It makes sense then to separate
this support out into common code instead of duplicating it in all
of the NIC drivers. The mii code also handles all of the media
detection, selection and reporting via the ifmedia interface.
This is basically the same code from NetBSD's /sys/dev/mii, except
it's been adapted to FreeBSD's bus architecture. The advantage to this
is that it automatically allows everything to be turned into a
loadable module. There are some common functions for use in drivers
once an miibus has been attached (mii_mediachg(), mii_pollstat(),
mii_tick()) as well as individual PHY drivers. There is also a
generic driver for all PHYs that aren't handled by a specific driver.
It's possible to do this because all 10/100 PHYs implement the same
general register set in addition to their vendor-specific register
sets, so for the most part you can use one driver for pretty much
any PHY. There are a couple of oddball exceptions though, hence
the need to have specific drivers.
There are two layers: the generic "miibus" layer and the PHY driver
layer. The drivers are child devices of "miibus" and the "miibus" is
a child of a given NIC driver. The "miibus" code and the PHY drivers
can actually be compiled and kldoaded as completely separate modules
or compiled together into one module. For the moment I'm using the
latter approach since the code is relatively small.
Currently there are only three PHY drivers here: the generic driver,
the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding
others later as I convert various NIC drivers to use this code.
I realize that I'm cvs adding this stuff instead of importing it
onto a separate vendor branch, but in my opinion the import approach
doesn't really offer any significant advantage: I'm going to be
maintaining this stuff and writing my own PHY drivers one way or
the other.
a module. Also modified the code to work on FreeBSD/alpha and added
device vr0 to the alpha GENERIC config.
While I was in the neighborhood, I noticed that I was still using
#define NFPX 1 in all of the Makefiles that I'd copied from the fxp
module. I don't really use #define Nfoo X so it didn't matter, but
I decided to customize this correctly anyway.
ethernet controllers based on the AIC-6915 "Starfire" controller chip.
There are single port, dual port and quad port cards, plus one 100baseFX
card. All are 64-bit PCI devices, except one single port model.
The Starfire would be a very nice chip were it not for the fact that
receive buffers have to be longword aligned. This requires buffer
copying in order to achieve proper payload alignment on the alpha.
Payload alignment is enforced on both the alpha and x86 platforms.
The Starfire has several different DMA descriptor formats and transfer
mechanisms. This driver uses frame descriptors for transmission which
can address up to 14 packet fragments, and a single fragment descriptor
for receive. It also uses the producer/consumer model and completion
queues for both transmit and receive. The transmit ring has 128
descriptors and the receive ring has 256.
This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus
so that it can be compiled as a loadable kernel module. Support for BPF
and hardware multicast filtering is included.
