mdoc(7) police: properly use a -diag list in the DIAGNOSTICS section.

Reviewed by:	ru
This commit is contained in:
Dima Dorfman 2001-04-13 19:59:47 +00:00
parent ef0180ed69
commit 19ab52cb4e
11 changed files with 24 additions and 30 deletions

View File

@ -333,8 +333,8 @@ RTM_CHANGE.
As such, only the super-user may modify
the routing tables.
.Sh DIAGNOSTICS
.Bl -tag -width Ds
.It Sy "add [host \&| network ] %s: gateway %s flags %x"
.Bl -diag
.It "add [host \&| network ] %s: gateway %s flags %x"
The specified route is being added to the tables. The
values printed are from the routing table entry supplied
in the
@ -344,21 +344,21 @@ If the gateway address used was not the primary address of the gateway
(the first one returned by
.Xr gethostbyname 3 ) ,
the gateway address is printed numerically as well as symbolically.
.It Sy "delete [ host \&| network ] %s: gateway %s flags %x"
.It "delete [ host \&| network ] %s: gateway %s flags %x"
As above, but when deleting an entry.
.It Sy "%s %s done"
.It "%s %s done"
When the
.Cm flush
command is specified, each routing table entry deleted
is indicated with a message of this form.
.It Sy "Network is unreachable"
.It "Network is unreachable"
An attempt to add a route failed because the gateway listed was not
on a directly-connected network.
The next-hop gateway must be given.
.It Sy "not in table"
.It "not in table"
A delete operation was attempted for an entry which
wasn't present in the tables.
.It Sy "routing table overflow"
.It "routing table overflow"
An add operation was attempted, but the system was
low on resources and was unable to allocate memory
to create the new entry.

View File

@ -55,9 +55,8 @@ If the secondary
DMA channel is C, set the flags to (C | 0x10). For a sound card without the
secondary DMA channel, the flags should be set to zero.
.Sh DIAGNOSTICS
.Bl -tag -width 2m
.Bl -diag
.It xxx: gus pcm not attached, out of memory
.Pp
There are not enough memory to drive the device.
.El
.Sh HISTORY

View File

@ -57,13 +57,11 @@ If the secondary
DMA channel is C, set the flags to (C | 0x10). For a sound card without the
secondary DMA channel, the flags should be set to zero.
.Sh DIAGNOSTICS
.Bl -tag -width 2m
.Bl -diag
.It sb_dspwr(XX) timed out.
.Pp
A command to the DSP has timed out.
Check the I/O port configuration.
.It bad irq XX (5/7/9/10 valid)
.Pp
The IRQ given to the driver is not valid.
.El
.Sh HISTORY

View File

@ -55,9 +55,8 @@ If the secondary
DMA channel is C, set the flags to (C | 0x10). For a sound card without the
secondary DMA channel, the flags should be set to zero.
.Sh DIAGNOSTICS
.Bl -tag -width 2m
.Bl -diag
.It xxx: gus pcm not attached, out of memory
.Pp
There are not enough memory to drive the device.
.El
.Sh HISTORY

View File

@ -57,13 +57,11 @@ If the secondary
DMA channel is C, set the flags to (C | 0x10). For a sound card without the
secondary DMA channel, the flags should be set to zero.
.Sh DIAGNOSTICS
.Bl -tag -width 2m
.Bl -diag
.It sb_dspwr(XX) timed out.
.Pp
A command to the DSP has timed out.
Check the I/O port configuration.
.It bad irq XX (5/7/9/10 valid)
.Pp
The IRQ given to the driver is not valid.
.El
.Sh HISTORY

View File

@ -67,7 +67,7 @@ otherhost 7:36am up 6 days, 16:45, load average: 0.20, 0.23, 0.18
example%
.Ed
.Sh DIAGNOSTICS
.Bl -tag -width indent
.Bl -diag
.It rup: RPC: Program not registered
The
.Xr rpc.rstatd 8

View File

@ -75,17 +75,17 @@ logged in, the amount of time since the user typed on the keyboard,
and the remote host they logged in from (if applicable).
.El
.Sh DIAGNOSTICS
.Bl -tag -width indent
.It Nm Ns : RPC: Program not registered
.Bl -diag
.It rusers: RPC: Program not registered
The
.Xr rpc.rusersd 8
daemon has not been started on the remote host.
.It Nm Ns : RPC: Timed out
.It rusers: RPC: Timed out
A communication error occurred. Either the network is
excessively congested, or the
.Xr rpc.rusersd 8
daemon has terminated on the remote host.
.It Nm Ns : "RPC: Port mapper failure - RPC: Timed out"
.It rusers: "RPC: Port mapper failure - RPC: Timed out"
The remote host is not running the portmapper (see
.Xr portmap 8 ) ,
and cannot accommodate any RPC-based services. The host may be down.

View File

@ -52,7 +52,7 @@ message to be sent can be typed in and terminated with EOF or it can
be in a
.Ar file .
.Sh DIAGNOSTICS
.Bl -tag -width indent
.Bl -diag
.It rwall: RPC: Program not registered
The
.Xr rpc.rwalld 8

View File

@ -195,12 +195,12 @@ lock file for queue control
.Xr printcap 5 ,
.Xr lpd 8
.Sh DIAGNOSTICS
.Bl -tag -width indent
.It Sy "?Ambiguous command"
.Bl -diag
.It "?Ambiguous command"
abbreviation matches more than one command
.It Sy "?Invalid command"
.It "?Invalid command"
no match was found
.It Sy "?Privileged command"
.It "?Privileged command"
you must be a member of group "operator" or root to execute this command
.El
.Sh HISTORY

View File

@ -128,7 +128,7 @@ log file for master timed
.%A S. Zatti
.Re
.Sh DIAGNOSTICS
.Bl -tag -width Ds -compact
.Bl -diag
.It ?Ambiguous command
abbreviation matches more than one command
.It ?Invalid command

View File

@ -133,8 +133,8 @@ arguments may be used to supplant the defaults.
.Xr netstat 1 ,
.Xr setsockopt 2
.Sh DIAGNOSTICS
.Bl -tag -width Ds
.It Sy no namelist
.Bl -diag
.It no namelist
When the system image doesn't
contain the proper symbols to find the trace buffer;
others which should be self explanatory.