ADMtek AL981 "Comet" chipset. The AL981 is yet another DEC tulip clone,
except with simpler receive filter options. The AL981 has a built-in
transceiver, power management support, wake on LAN and flow control.
This chip performs extremely well; it's on par with the ASIX chipset
in terms of speed, which is pretty good (it can do 11.5MB/sec with TCP
easily).
I would have committed this driver sooner, except I ran into one problem
with the AL981 that required a workaround. When the chip is transmitting
at full speed, it will sometimes wedge if you queue a series of packets
that wrap from the end of the transmit descriptor list back to the
beginning. I can't explain why this happens, and none of the other tulip
clones behave this way. The workaround this is to just watch for the end
of the transmit ring and make sure that al_start() breaks out of its
packet queuing loop and waiting until the current batch of transmissions
completes before wrapping back to the start of the ring. Fortunately, this
does not significantly impact transmit performance.
This is one of those things that takes weeks of analysis just to come
up with two or three lines of code changes.
Implement priorities.
GENERIC, LINT, files:
Remove remarks about ordering of device names.
GENERIC, LINT:
Sort the devices alphabetically in LINT and GENERIC.
The specific intent of this commit is to pave the way for importing
Compaq XP1000 support. These changes should not affect the i386 port.
Reviewed by: Doug Rabson <dfr@nlsystems.com>
(actually, he walked me through most of it & deserves more than reviewd-by
credit )
Fixed problems:
LS120/ZIP drives still currupted data.
Reworked once again, buffered I/O is just ignoring any sizehints
it is given :(
Now the atapifd driver splits up requests for devices that has
limitted transfer size.
ISA only configs fails on boot with interrupt timeouts.
The new-bus integration introduced a bug where the softc ptr
was lost during the probe.
Some minor cleanups and rearrangements as well.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, again you have been warned :)
Notebook owners should be carefull that their machines dont suspend
as this might cause trouble...
But please tell me how it works for you!
Enjoy!
motherboard will have a card for the "motherboard" on slot 0.
eisa0: <EISA bus> on motherboard
mainboard0: <ASU5101 (System Board)> at slot 0 on eisa0
This should stop the probe "detecting" an EISA bus everywhere that has
a 'controller eisa0' line regardless of whether it's really there.
A very nice i/o board with 16 open collector outputs (capable of driving 5-40v)
and 16 inputs
Also has 2 16 bit cascadable counters (10Mhz clock) capable of
generating interrupts.
It is a PCI card, and emulates the Intel 8254 timer.
It uses the PLX PCI-9050 PCI bus interface to map the
8254 style hardware and the i/o registers into the IO space.
Developed by Jennifer Clark <jen@vulture.dmem.strath.ac.uk>
Strathclyde University Transparent Telepresence Research Group
Change Intel GPIO mask to hopefully stop turning the Intel Camera off
Fixed tuner selection on Hauppauge card with tuner 0x0a
Replaced none tuner with no tuner for Theo de Raadt <deraadt@openbsd.org>.
Ivan Brawley <brawley@internode.com.au> added
the Australian channel frequencies.
Clean up the handling of failure modes in our attach so we don't free
resources twice. ahc_free() will do all of the work for us (as would
be required by an unload event) so we only need to handle resources that
the softc has not taken ownership of.
Fixed problems:
LS120 drives currupted data.
The workaround for drives not supporting upto 64K transfers
has been reworked. It works now both on LS120 & ZIP drives.
ISA only configs wont compile.
Fixed.
The ATA driver wont share interrupts.
Fixed.
The "unwanted interrupt" warning gave wrong controller.
Another lun<>unit messup from the newbus integration.
Some minor cleanups and rearrangements as well.
As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code.
Especially the DMA support can hose your disk real bad if anything
goes wrong, again you have been warned :)
Notebook owners should be carefull that their machines dont suspend
as this might cause trouble...
But please tell me how it works for you!
Enjoy!
-Søren
Submitted by: adrian@freebsd.org
Change reference count in struct ifaddr to a u_int, to be able
to handle more than 2^16 routes to the same interface.
Fix suggested by Andrew Bangs <andrewb@demon.net> in PR kern/10570.
Tested by <adrian@freebsd.org> and me under -current.
Remove a useless argument from vm_map_madvise's interface (vm_map.c,
vm_map.h, and vm_mmap.c).
Remove a redundant test in vm_uiomove (vm_map.c).
Make two changes to vm_object_coalesce:
1. Determine whether the new range of pages actually overlaps
the existing object's range of pages before calling vm_object_page_remove.
(Prior to this change almost 90% of the calls to vm_object_page_remove
were to remove pages that were beyond the end of the object.)
2. Free any swap space allocated to removed pages.
though, on systems (386 mostly) that still have a seperate fpu, but it
might be possible to find systems where the FPU coprocessor is wired to
a different IRQ pin.
docs don't seem to shed light on why this is needed, but reports from
the field indicate this helps prevent problems in this area. Ken's
changes seem to have exposed this bug, rather than caused it, as far
as I can tell.
Thanks to Jack O'Neill for tracking this down.
Submitted by: jack@germanium.xtalwind.net
Very strong 3.2 merge candidate.
It never makes sense to specify MAP_COPY_NEEDED without also specifying
MAP_COPY_ON_WRITE, and vice versa. Thus, MAP_COPY_ON_WRITE suffices.
Reviewed by: David Greenman <dg@root.com>
instances to a parent bus.
* Define a new method BUS_ADD_CHILD which can be called from DEVICE_IDENTIFY
to add new instances.
* Add a generic implementation of DEVICE_PROBE which calls DEVICE_IDENTIFY
for each driver attached to the parent's devclass.
* Move the hint-based isa probe from the isa driver to a new isahint driver
which can be shared between i386 and alpha.
Sync up device Ids with the master Adaptec list.
Add probe support for the 2940 Pro although it isn't obvious that
all of the termination support is correct for this adapter yet.
tell the sequencer to pause itself for a target msg variable update. This
avoids the pause race entirely as HS_MAILBOX can be accessed without
pausing the chip.
3.2 Merge candidate.
v1.19 (1999/04/15) updates the CEM56/REM56 support.
Current bugs & misfeatures
--------------------------
* CE2 cards still not working reliably. Unclear if this is related to
packet I/O code or interrupt handling.
* Autonegotiation support remains flaky. We're now OK with 10Mbit auto
hubs, but certain combination of hardware will fail to connect.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
v1.19 (1999/04/15) updates the CEM56/REM56 support.
Current bugs & misfeatures
--------------------------
* CE2 cards still not working reliably. Unclear if this is related to
packet I/O code or interrupt handling.
* Autonegotiation support remains flaky. We're now OK with 10Mbit auto
hubs, but certain combination of hardware will fail to connect.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
v1.18 (1999/04/08) adds support for CEM56 and REM56 multifunction cards.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
v1.18 (1999/04/08) adds support for CEM56 and REM56 multifunction cards.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
v1.17 (1999/03/28) has xperimental fixes to 10Mbit autonegotiation and
CE2 input lockup.
KNOWN BUGS
==========
* Media auto-negotiation is definitely not right. It will work in most
circumstances and seems to connect OK to most 100Mbit networks, however some
pathological combinations of hubs/networks/peers seem to confuse it.
* CE2 support is somewhat flakey (ranging from 'works perfectly' to 'hangs the
machine' so far). I've fixed the probe routine and a potential lockup in
the output routine, but a lot of people still report that they can't receive
or transmit.
* You won't be able to use the modem and Ethenet parts of a multifunction card
simultaneously. This is limitation the current FreeBSD PCMCIA support.
Likewise, there is no support for CardBus devices.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
v1.17 (1999/03/28) has xperimental fixes to 10Mbit autonegotiation and
CE2 input lockup.
KNOWN BUGS
==========
* Media auto-negotiation is definitely not right. It will work in most
circumstances and seems to connect OK to most 100Mbit networks, however some
pathological combinations of hubs/networks/peers seem to confuse it.
* CE2 support is somewhat flakey (ranging from 'works perfectly' to 'hangs the
machine' so far). I've fixed the probe routine and a potential lockup in
the output routine, but a lot of people still report that they can't receive
or transmit.
* You won't be able to use the modem and Ethenet parts of a multifunction card
simultaneously. This is limitation the current FreeBSD PCMCIA support.
Likewise, there is no support for CardBus devices.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
v1.16 (1999/03/08) fixed BPF input hang and infinite loop on CE2
short-packet output.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
v1.16 (1999/03/08) fixed BPF input hang and infinite loop on CE2
short-packet output.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
This driver is mostly based on the `xirc2ps' driver for Linux by Werner
Koch. Werner has even allowed his code to be distributed under a BSD licence,
making our life considerably easier -- thanks Werner!
This driver supports:
* Intel EtherExpress(TM) PRO/100 PCCARD (16-bit version)
* Xircom CreditCard CE2 / CEM28 / CEM33 / CE3 / CEM56 Ethernet adapters.
* Toshiba Advanced Network 10/100 PCCARD
* Certain Compaq Netelligent 10/100 branded cards
v1.14 has major changes to media selection code, and bugfixes in the
probe routine.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
This driver is mostly based on the `xirc2ps' driver for Linux by Werner
Koch. Werner has even allowed his code to be distributed under a BSD licence,
making our life considerably easier -- thanks Werner!
This driver supports:
* Intel EtherExpress(TM) PRO/100 PCCARD (16-bit version)
* Xircom CreditCard CE2 / CEM28 / CEM33 / CE3 / CEM56 Ethernet adapters.
* Toshiba Advanced Network 10/100 PCCARD
* Certain Compaq Netelligent 10/100 branded cards
v1.14 has major changes to media selection code, and bugfixes in the
probe routine.
Developed by: Scott Mitchell <scott@uk.freebsd.org>
Obtained from: http://www.freebsd-uk.eu.org/~scott/xe_drv/
inodes were synced every 15 seconds. This is now reversed as during
directory create, we cannot commit the directory entry until its
inode has been written. With this switch, the inodes will be more
likely to be written by the time that the directory is written thus
reducing the number of directory rollbacks that are needed.
a sync on the block device for the filesystem. That allows it to push the
bitmap blocks before the inode blocks which greatly reduces the number of
inode rollbacks that need to be done.
driver to use bus_space_read_foo()/bus_space_write_foo(). The line is not
visible unless you compile the driver to use PCI memory mapped mode, which
not done by default, but it should be fixed anyway.
Changed to `const void *'. utrace() is undocumented, so nothing should
notice.
Fixed missing consts for utrace() and ktrace() in syscalls.master.
sys/ktrace.h is missing some Lite2 changes of shorts to ints.
with malloc type at the tail of the list changed the list from
linear to circular. This seemed to cause surprisingly few problems,
but it now causes weird output from `vmstat -m', probably because
a more important malloc type is now at the tail of the list.
Fix it by abusing ks_limit instead of ks_next as a flag for being
on the list. Don't forget to clear the flag when a malloc type is
uninit'ed. Uninit'ing is still fundamentally broken -- it loses
history.
udev_t in the kernel but still called dev_t in userland.
Provide functions to manipulate both types:
major() umajor()
minor() uminor()
makedev() umakedev()
dev2udev() udev2dev()
For now they're functions, they will become in-line functions
after one of the next two steps in this process.
Return major/minor/makedev to macro-hood for userland.
Register a name in cdevsw[] for the "filedescriptor" driver.
In the kernel the udev_t appears in places where we have the
major/minor number combination, (ie: a potential device: we
may not have the driver nor the device), like in inodes, vattr,
cdevsw registration and so on, whereas the dev_t appears where
we carry around a reference to a actual device.
In the future the cdevsw and the aliased-from vnode will be hung
directly from the dev_t, along with up to two softc pointers for
the device driver and a few houskeeping bits. This will essentially
replace the current "alias" check code (same buck, bigger bang).
A little stunt has been provided to try to catch places where the
wrong type is being used (dev_t vs udev_t), if you see something
not working, #undef DEVT_FASCIST in kern/kern_conf.c and see if
it makes a difference. If it does, please try to track it down
(many hands make light work) or at least try to reproduce it
as simply as possible, and describe how to do that.
Without DEVT_FASCIST I belive this patch is a no-op.
Stylistic/posixoid comments about the userland view of the <sys/*.h>
files welcome now, from userland they now contain the end result.
Next planned step: make all dev_t's refer to the same devsw[] which
means convert BLK's to CHR's at the perimeter of the vnodes and
other places where they enter the game (bootdev, mknod, sysctl).
Use colons instead of semi-colons in the default init_path to behave like
UNIX instead of DOS.
Suggested by: bde
Reminded by: des (with no hint as to *which* man page).
bad math: it does not handle page-boundary conditions, and will not
end up mapping all of the requested addresses. This will cause a panic:
page fault during probe on some systems. I have a machine that will
panic every time (when using the dpt driver) on kernel probe when there
are 5 drives installed. When there are 4 drives, it is fine.
Fix is to always allocate/deallocate an extra page.
There is also a bonus splx() fix on an early error return.
Submitted by: Mark J. Taylor <mtaylor@cybernet.com>
PR: 9367
some aha 1542B cards will return 0x7f for the unimplemented GEOMETRY
register.
This is a good 3.2 candidate.
PR: 11469
Submitted by: Thomas David Rivers
displace a real driver.
Revert rev 1.109.
Pick up a few things from elsewhere (a couple of SiS id's).
As an *experiment*, have the chip* driver claim (for reporting purposes)
IDE controllers if there isn't another PCI-aware ide or ata driver to
grab them. I've exported the match function since it could be used from
the ata-all.c code replacing ata_pcimatch() - but I have not touched the
ata code. I'd like to catch a few more devices this way, including USB
and other bridges etc.
massive thwunking to include an XS_CHANNEL value. Some changes of how
parameters are reported to outer layers (including bus, e.g.). Yet more
stirring around in isp_mboxcmd to try and get it right. Decode of 1080/1240
NVRAM.
with other reset handling in rev.1.83 but broke it in rev.1.120. The
breakage didn't seem to cause any problems even on the system which had
problems ("extra" interrupts and botched handling thereof) before rev.1.83.
It only affects multi-floppy systems anyway.
after some of the previous commits). Add in support for the 1240
dual channel ISP card. Try the dance of unmapping a PCI interrupt
if we don't configure (if that ever works it'll be helpful).
SUPPORTED). Add a SA_FLAG_TAPE_FROZEN for (see below).
Add a queue_count field to softc.
Add HP T20* Travan-5 like tape device as a FIXED/512 type device.
Works for me. Add TANDBERG SLR5 as a variable SA_QUIRK_1FM device.
Change VIPER 2525 to 1024 byte blocksize. It's possible other
drives should change too, but see below..
Change argument to sagetparams to be pointer to a sa_comp_t union-
this can be either a DATA COMPRESSION or a DEVICE CONFIGURATION
page. In general compression now tries to use the DATA COMPRESSION
page and if that fails tries the DEVICE CONFIGURATION page.
Change close routine to not rewind tape if there's a failure in either
writing filemarks or in backing over one of two filemarks for a 2FM
at EOT tape- instead mark the tape as 'frozen' and print a message
saying that either an OFFLINE or REWIND or an MTEOM command is needed
to clear this state (all bring certainty back to tape position). Fix
sastrategy to not allow I/O to a frozen tape.
Add MTIOCGETEOTMODEL/MTIOCSETEOTMODEL ioctls that get and set the EOT
model for a tape drive (you can now dynamically change whether it's
a 2 FM @ EOT or 1FM at EOT tape device). This ought to give folks
something to handle the QIC drives we don't know about. Correctly propagate
record of compression algorithm back. Clear FROZEN flag for EOM, REWIND
and OFFLINE (and RETENSION and ERASE) cases.
Fix an egregious bug in sadone that had left the device queue frozen
for deferred (for fixed mode case) errors.
Add comment in samount about how useless the test unit ready is for
invalidating a mount (this has to be fixed later).
Fix residual calculation (per Eivind) in saerror so that negative values
for tape records being too large for the supplied buffer get caught. Do
some other saerrro cleanup.
Per Ken && Justin, add my name to copyright comment.
entity. Add the Device Configuration page data structure- this structure
should be used if you fail to fetch the DATA COMPRESSION page. Make a union
type of a mode header, a device configuration page and the data compression
page.
Add a couple of QIC density defines (QIC 2G/QIC 4GB).
manuals specifically say that reading the counters using the rdmsr
instruction returns a 64 bit value of which the higher 24 bits are
undefined. The code that reads the counters should then clear the
high 24 bits.
PR: i386/10632
but was fairly harmless because not many devices have statically
configured msizes (none should have, but old-bus is missing post-probe
checks for maddr/msize conflicts, so sizes had to be statically
configured for maddr/msize conflict checking to actually work).
PR: 11146 (side issue)
unp_internalize() takes a reference to the descriptor. If the send
fails after unp_internalize(), the control mbuf would be freed ophaning
the reference.
Tested in -CURRENT by: Pierre Beyssac <beyssac@enst.fr>
through' to the C compiler.
* Allow the interface to specify a default implementation for methods.
* Allow 'static' methods which are not device specific.
* Add a simple scheme for probe routines to return a priority value. To
make life simple, priority values are negative numbers (positive numbers
are standard errno codes) with zero being the highest priority. The
driver which returns the highest priority will be chosen for the device.
Fixed profiling of elf kernels. Made high resolution profiling compile
for elf kernels (it is broken for all kernels due to lack of egcs support).
Renaming of many assembler labels is avoided by declaring by declaring
the labels that need to be visible to gprof as having type "function"
and depending on the elf version of gprof being zealous about discarding
the others. A few type declarations are still missing, mainly for SMP.
PR: 9413
Submitted by: Assar Westerlund <assar@sics.se> (initial parts)
bttv's audio mux values.
Automatically locate the EEPROM i2c address and read the subsystem_vendor_id
from EEPROM and not the PCI registers.
Add NSMBUS checks around smbus/iicbus i2c bus code
Add GPIO mask for the audio mux to each card type.
Add CARD_ZOLTRIX and CARD_KISS from mailing list searches.
Tested by: Paul Reece <paul@fastlane.net.au>,
Ivan Brawley <brawley@internode.com.au> and
Gilad Rom <rom_glsa@ein-hashofet.co.il>
implicitly LOCK'ed instruction), so there shouldn't be any harm in making
it volatile pointer compatable for one of the users of it. It seems to
generate the same code regardless.
was available to the programmer to hold chip state information:
Use the SDID register instead of CTEST3. This change actually
simplifies the SCRIPTS code, but I'm not absolutely sure, that
it is OK for all variants of NCR chips around and all device
combinations. I have had this code running on several systems
with 53c810, 875 and 895 controllers for several months.
Suggested by: Gerard Roudier <groudier@club-internet.fr>
a pointer to 'makeoptions' and /etc/make.conf.
Catch a few stray "kernel" hardcoded references.
Move the kernel.debug and related kernel build rules together.
upset about it (and generate things like __main() calls that are reserved
for main()). Renaming was phk's suggestion, but I'd already thought about
it too. (phk liked my suggested name tada() but I decided against it :-)
Reviewed by: phk
directly into the Makefile. Remove references to swapkernel.c, it's
not generated by config(8) now. (The previous config commits had
generated it, but they had an unused 'char *' in them).
#define COMPAT_PCI_DRIVER(name,data) DATA_SET(pcidevice_set,data)
.. to 2.2.x and 3.x if people think it's worth it. Driver writers can do
this if it's not defined. (The reason for this is that I'm trying to
progressively eliminate use of linker_sets where it hurts modularity and
runtime load capability, and these DATA_SET's keep getting in the way.)
although this is pretty trivial. devclass_get_softc() is a tad more
expensive than the old com_addr() implementation. If Bruce is really
worried about the cost of this, it could always be changed so that the
softc pointer is stored in a local array again.
config kernel mumble mumble
line has been obsoleted and removed and with it went all knowledge of
devices on the part of config.
You can still configure a root device (which is used if you give
the "-r" flag) but now with an option:
options ROOTDEVNAME=\"da0s2e\"
The string is parsed by the same code as at the "boot -a" prompt.
At the same time, make the "boot -a" prompt both more able and more
informative.
ALPHA/PC98 people: You will have to adapt a few simple changes
(defining rootdev and dumpdev somewhere else) before config works
for you again, sorry, but it's all in the name of progress.
interrupt configuration reported. (I just discovered my vga card is
being configured for irq 5... :-) This is just reporting. The vga_isa
driver does the real work using the isa compat mappings.
I'm not too happy about the result either, but at least it has less
chance of backfiring.
This particular feature could be called "a mess" without offending
anybody.
If the client requests that the error recovery code retry a selection
timeout, it will be retried after half a second. The delay is to give the
device time to recover.
For most of these drivers, I only added selection timeout retries where
they were also retrying unit attention type errors. The sa(4) driver calls
saerror() in a number of places, but most of them don't request retrying
unit attentions.
Also, bump the default minimum CD changer timeout from 2 to 5 seconds and
the maximum timeout from 10 to 15 seconds. Some Pioneer changers seem to
have trouble with the shorter timeout.
Reviewed by: gibbs
- first program lock a region in a file,
- second program wait on the lock,
- first program extend the region,
- second program interrupted by a signal.
and ISA DMA channels (ie: on most PCI systems, they are not.. they are
on the ISA side of the PCI-ISA bridge and could be duplicated if there
were multiple PCI-ISA bridges, say in a laptop docking station), while
the APIC resources would be global on SMP systems.
Also, revert a previous change, change some printfs back to panics.
that big a deal just yet and isn't worth a whole line on the boot screen.
This could change later in the face of multi-ISA-bus (eg: laptop docking
stations with two independent ISA busses) and SMP/APIC systems. The Alpha
already has multiple interrupt destinations to deal with.
development that leads to lots of crashes during boot.
I have made a 'reinstall' target (like in ports, and reinstall.debug)
This is most useful if you want to keep /kernel.old as a known bootable
kernel. If you test a new kernel and have to reboot for a fix, a
'make reinstall' will install the new kernel over the top of the old
non-viable one, leaving the old one untouched. This is mainly meant
for development, not general users.
Change haveseen_isadev() to something a little easier to emulate.
Store the device_t for the wrapper in isa_device.
Implement a replacement for haveseen_isadev - namely haveseen_ioport()
which takes a port size as an extra argument for a proper range check.
This (haveseen_ioport()) has not been tested, but I think it'll work.
new isa drivers with sensitive flags. If the resource_find() code
is meant to "find" the wildcard sensitive flag for a driver even though
a unit is supplied, this can be simplified.
Restore 0x710110b9 ("AcerLabs M15x3 Power Management Unit") - but only
if NALPM == 0.
Restore 0x00051166 ("Ross (?) host to PCI bridge") so that
fixbushigh_Ross() gets called.
Delete generic_pci_bridge(), it's been replaced by other mechanisms (see
the isab and pcib match/probes and the pci_bridge_type() function)
o fix DDB support
- include "opt_ddb.h"
- fix Debugger() arg
pointed out by bde
o back out pvc shadow interface support
- it is currently not used
- to make it easier to merge another implementation
o misc minor cleanup
particularly annoying hack, namely having the linker bash the moduledata
to set the container pointer, preventing it being const. In the process,
a stack of warnings were fixed and will probably allow a revisit of the
const C_SYSINIT() changes. This explicitly registers modules in files or
preload areas with the module system first, and let them initialize via
SYSINIT/DECLARE_MODULE later in their SI_ORDER_xxx order. The kludge of
finding the containing file is no longer needed since the registration
of modules onto the modules list is done in the context of initializing
the linker file.
sysinits, for example, are sorted by swapping those objects(!). Perhaps
they should be const and the sysinit sorting should be swapping the
pointers rather than the targets. This is on my revisit list, but it
has the side effect of removing a lot of warnings. With -Wcast-qual, it
doesn't seem easy to get rid of the constness when you *know* it's not.
(With apologies to bde, this essentially reverts rev 1.21 of kernel.h
from back in 1996)
Made a new (inline) function devsw(dev_t dev) and substituted it.
Changed to the BDEV variant to this format as well: bdevsw(dev_t dev)
DEVFS will eventually benefit from this change too.
Virtualize bdevsw[] from cdevsw. bdevsw() is now an (inline)
function.
Join CDEV_MODULE and BDEV_MODULE to DEV_MODULE (please pay attention
to the order of the cmaj/bmaj arguments!)
Join CDEV_DRIVER_MODULE and BDEV_DRIVER_MODULE to DEV_DRIVER_MODULE
(ditto!)
(Next step will be to convert all bdev dev_t's to cdev dev_t's
before they get to do any damage^H^H^H^H^H^Hwork in the kernel.)
Mark the GDB port in the config file with flags 0x80. Currently
only the sio driver checks these flags and sets up a GDB port,
but adding similar code to other serial drivers would be easy.
For backward compatibility, if an sio port is marked as the console
and no port is marked as the gdb port, the GDB port will be mapped
to the console port. This hack should go away at some point.
power management. This will only work on newer firmware revisions; older
firmware will silently ignore the attempts to turn power management on.
Patches supplied by: Brad Karp <karp@eecs.harvard.edu>
files at once on a filesystem running soft updates. The root of
the problem is that soft updates limits the amount of memory that
may be allocated to dependency structures so as to avoid hogging
kernel memory. The original algorithm just waited for the disk I/O
to catch up and reduce the number of dependencies. This new code
takes a much more aggressive approach. Basically there are two
resources that routinely hit the limit. Inode dependencies during
periods with a high file creation rate and file and block removal
dependencies during periods with a high file removal rate. I have
attacked these problems from two fronts. When the inode dependency
limits are reached, I pick a random inode dependency, UFS_UPDATE
it together with all the other dirty inodes contained within its
disk block and then write that disk block. This trick usually
clears 5-50 inode dependencies in a single disk I/O. For block and
file removal dependencies, I pick a random directory page that has
at least one remove pending and VOP_FSYNC its directory. That
releases all its removal dependencies to the work queue. To further
hasten things along, I also immediately start the work queue process
rather than waiting for its next one second scheduled run.
NOTE: These changes will require recompilation of any userland
applications, like cdrecord, xmcd, etc., that use the CAM passthrough
interface. A make world is recommended.
camcontrol.[c8]:
- We now support two new commands, "tags" and "negotiate".
- The tags commands allows users to view the number of tagged
openings for a device as well as a number of other related
parameters, and it allows users to set tagged openings for
a device.
- The negotiate command allows users to enable and disable
disconnection and tagged queueing, set sync rates, offsets
and bus width. Note that not all of those features are
available for all controllers. Only the adv, ahc, and ncr
drivers fully support all of the features at this point.
Some cards do not allow the setting of sync rates, offsets and
the like, and some of the drivers don't have any facilities to
do so. Some drivers, like the adw driver, only support enabling
or disabling sync negotiation, but do not support setting sync
rates.
- new description in the camcontrol man page of how to format a disk
- cleanup of the camcontrol inquiry command
- add support in the 'devlist' command for skipping unconfigured devices if
-v was not specified on the command line.
- make use of the new base_transfer_speed in the path inquiry CCB.
- fix CCB bzero cases
cam_xpt.c, cam_sim.[ch], cam_ccb.h:
- new flags on many CCB function codes to designate whether they're
non-immediate, use a user-supplied CCB, and can only be passed from
userland programs via the xpt device. Use these flags in the transport
layer and pass driver to categorize CCBs.
- new flag in the transport layer device matching code for device nodes
that indicates whether a device is unconfigured
- bump the CAM version from 0x10 to 0x11
- Change the CAM ioctls to use the version as their group code, so we can
force users to recompile code even when the CCB size doesn't change.
- add + fill in a new value in the path inquiry CCB, base_transfer_speed.
Remove a corresponding field from the cam_sim structure, and add code to
every SIM to set this field to the proper value.
- Fix the set transfer settings code in the transport layer.
scsi_cd.c:
- make some variables volatile instead of just casting them in various
places
- fix a race condition in the changer code
- attach unless we get a "logical unit not supported" error. This should
fix all of the cases where people have devices that return weird errors
when they don't have media in the drive.
scsi_da.c:
- attach unless we get a "logical unit not supported" error
scsi_pass.c:
- for immediate CCBs, just malloc a CCB to send the user request in. This
gets rid of the 'held' count problem in camcontrol tags.
scsi_pass.h:
- change the CAM ioctls to use the CAM version as their group code.
adv driver:
- Allow changing the sync rate and offset separately.
adw driver
- Allow changing the sync rate and offset separately.
aha driver:
- Don't return CAM_REQ_CMP for SET_TRAN_SETTINGS CCBs.
ahc driver:
- Allow setting offset and sync rate separately
bt driver:
- Don't return CAM_REQ_CMP for SET_TRAN_SETTINGS CCBs.
NCR driver:
- Fix the ultra/ultra 2 negotiation bug
- allow setting both the sync rate and offset separately
Other HBA drivers:
- Put code in to set the base_transfer_speed field for
XPT_GET_TRAN_SETTINGS CCBs.
Reviewed by: gibbs, mjacob (isp), imp (aha)
WaveLAN's radio modem. The default is whatever the NIC uses since NICs
sold in different countries may default to different frequencies. (The
Lose95/LoseNT software doesn't let you select the channel so it's probably
not really meant to be changed.)
- Change to the same transmit scheme as the PNIC driver.
- Dynamically set the cache alignment, and set burst size the same as
the PNIC driver in mx_init().
- Enable 'store and forward' mode by default. This is the slowest option
and it does reduce 100Mbps performance somewhat, but it's the most
reliable setting I can find. I'm more interested in having the driver
work reliably than trying to squeeze the best performance out of it.
The reason I'm doing this is that on *some* systems you may see a lot
of transmit underruns (which I can't explain: these are *fast* test
systems) and these errors seem to cause unusual and decidedly
non-tulip-like behavior. In normal 10Mbps mode, performance is fine
(you can easily saturate a 10Mbps link).
Also tweak some of the other drivers:
- Increase the size of the TX ring for the Winbond, ASIX, VIA Rhine
and PNIC drivers.
- Set a larger value for ifq_maxlen in the ThunderLAN driver. The setting
of TL_TX_LIST_CNT - 1 is too low (the ThunderLAN driver only allocates
20 transmit descriptors, and I don't want to fiddle with that now
because the ThunderLAN's descriptor structure is an oddball size
compared to the others).
for elf kernels (it is broken for all kernels due to lack of egcs support).
Renaming of many assembler labels is avoided by declaring by declaring
the labels that need to be visible to gprof as having type "function"
and depending on the elf version of gprof being zealous about discarding
the others. A few type declarations are still missing, mainly for SMP.
PR: 9413
Submitted by: Assar Westerlund <assar@sics.se> (initial parts)
INIT_PATH config option.
Also fix two bugs which caused an infinite loop in none of the programs
in the init_path were found. That code was obviously not tested!
adapter (and some workalikes). Also add man pages and a wicontrol
utility to manipulate some of the card parameters.
This driver was written using information gleaned from the Lucent HCF Light
library, though it does not use any of the HCF Light code itself, mainly
because it's contaminated by the GPL (but also because it's pretty gross).
The HCF Light lacks certain featurs from the full (but proprietary) HCF
library, including 802.11 frame encapsulation support, however it has
just enough register information about the Hermes chip to allow someone
with enough spare time and energy to implement a proper driver. (I would
have prefered getting my hands on the Hermes manual, but that's proprietary
too. For those who are wondering, the Linux driver uses the proprietary
HCF library, but it's provided in object code form only.)
Note that I do not have access to a WavePOINT access point, so I have
only been able to test ad-hoc mode. The wicontrol utility can turn on
BSS mode, but I don't know for certain that the NIC will associate with
an access point correctly. Testers are encouraged to send their results
to me so that I can find out if I screwed up or not.
network adapters. These are all PCMCIA devices (the ISA version is a
PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a
wicontrol utility to read and write some of the card's parameters.
Note: I do not have access to a WavePOINT access point, so I have only
been able to test this driver in ad-hoc (point to point) mode. The
wicontrol utility allows programming the desired service set name (SSID)
and enabling BSS mode, but I can't tell for sure if it works (I know the
card switches modes, but I can't verify that it joins a service set
correctly).
This driver was written using information gleaned from the Lucent HCF Light
library, which is an API library designed to simplify driver development
for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light
is missing certain features (like 802.11 frame encapsulation!) which are
available only in the proprietary complete HCF code, which is not available
to the public. This driver uses none of the HCF Light code: it's very ugly
and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11
frames, everything else is encapsulated as 802.3.
(It would be easier to just get the Hermes programming manual, but that's
not publically available either. For those who are wondering, the Linux
WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in
object code form only. So much for supporting open source sofware.)
Multicast filter support is implemented, however it appears that the
filter doesn't work: programming in one IP mutlicast group enables them
all.
handler. This fixes pnp interrupts and would have fixed pccard interrupts
but a workaround has been applied there.
This the sound driver problems which people have reported with new-bus.
uses the AUI port with an on-board AUI to 10baseFL transceiver, not the
10baseT port like I had earlier suspected. The 3c900B-FL should be properly
supported now.
routines. The descriptor contains parameters which could be used
within those routines (eg. ip_output() ).
On passing, add IPPROTO_PGM entry to netinet/in.h
abuses its argument, which is supposed to be an integer unit number, as
a pointer to the head of the 'struct slot' list. When this code was
hacked^Wupdated for newbus, a new mechanism for registering slot_irq_handler()
was put in place and the significance of the unit number was overlooked.
When registering an interrupt, we have both device_id and unit. The unit
number is passed as 'unit' but /sys/i386/usa/intr_machdep.c:register_intr()
drops unit on the floor and uses device_id instead. Since pccard_alloc_intr()
always sets device_id to 0, this means the unit number is always zero, and
slot_irq_handler() is always called with 0, which becomes a NULL pointer
which slot_irq_handler() tries to dereference and the kernel explodes.
Result: if you assign a PCMCIA driver in the kernel config file like this:
device wi0 at isa? port? irq?
Then the system will panic the moment a PCMCIA device is attached and
an interrupt is triggered.
The quick fix: make pccard_alloc_intr() pass the unit number as both
the device_id and unit arguments to register_pcic_intr(). The correct fix
would be to rewrite /sys/pccard to be less disgusting.
+ plug an mbuf leak when dummynet used with bridging
+ make prototype of dummynet_io consistent with usage
+ code cleanup so that now bandwidth regulation is precise to the
bit/s and not to (8*HZ) bit/s as before.
Peter Wemm
Bruce Evans
Semen Ustimenko
Julian Elischer
Bill Paul
Kenneth D. Merry
Andrey A. Chernov
Doug Rabson
Eivind Eklund
Nick Hibma
Andrew Gallatin
Hellmuth Michaelis
Kazutaka YOKOTA
Søren Schmidt
KATO Takenori
Roger Hardiman
Robert Nordier
Luoqi Chen
Alan Cox
Justin T. Gibbs
Poul-Henning Kamp
Pierre Beyssac
Dmitrij Tejblum
David E. O'Brien
Greg Lehey
Warner Losh
Daniel C. Sobral
Joseph Koshy
Kirk McKusick
Mike Smith
Brian Somers
Jordan K. Hubbard
Matt Jacob
John Birrell
Mike Spengler
Paul Richards
Don Lewis
Dag-Erling Smørgrav
Stefan Eßer
Kenjiro Cho
Bill Fumerola
Luigi Rizzo