o Fix ``set timeout'' usage message and documentation.
o Change ifOutPackets, ifOutOctets and ifOutLQRs to `u_int32_t's
so that they wrap correctly.
o Put the LQR in network byte order using the correct struct size
(sizeof u_int32_t, not sizeof u_long).
o Wrap LQR ECHO counters correctly.
o Don't increment OutLQR count if the last LQR hasn't been replied
to.
o Initialise HisLqrData (last received LQR) in StartLqm.
o Don't start the LQR timer if we're `disabled' and `accepted'.
o Generate LQR responses when both sides are using a timer and
we're not going to send our next LQR before the peers max timeout.
LQR should now be fully functional.
may result in a our modem closing after it's made its way into
the fd_set, resulting in a program exit (with select(): bad file
descriptor) rather than a dropped link.
Don't mention the authors name at startup. He's already credited
in the man page. Instead, make the message consistent with the
one given to the diagnostic port (and fix the grammar when entering
`term' mode).
Don't credit the zlib author in the man page as ppp isn't linked
directly with zlib (it's shared).
Mention when the OpenBSD port was first made available.
The delay defaults to 1 sec (as it always has) unless we've done
a ~p in interactive mode or we've actually detected a HDLC frame.
This is now cleanly implemented (via async timers) so that it is
possible for LCP to come up despite the delay if an LCP REQ is
received.
This will hopefully solve situations with slow servers or slirp
scenarios (where ECHO is left on the port for a second or so before
the peer enters packet mode).
Also, ~p in interactive mode no longer changes the value of the default
openmode delay and -dedicated mode enters packet mode in the right state
according to the value of openmode.
When building a release, RELEASE_CRUNCH is defined for a `make' of
the objects required by the crunch of each program. The object list
is still obtained in the same way, so you must make sure that all
objects are built (empty if necessary) by this make. ppp/Makefile
provides an example.
Reviewed by: jkh
(I completely mis-read the rfc last time 'round!)
This means:
o Better CCP/WARN Reset diagnostics.
o After we've sent a REQ and before we've received an ACK, we drop
incoming compressed data and send another REQ.
o Before sending an ACK, re-sequence all pending PRI_NORMAL data in
the modem queue so that pending packets won't get to the peer
*after* the ResetAck.
o Send ACKs with the `identifier' from the REQ frame.
o After we've received a correct ACK, duplicate ACKs are ok (and will
reset our history).
o Incorrect ACKs (not matching the last REQ) are moaned about and dropped.
Also,
o Calculate the correct FCS after compressing a packet. DEFLATE
*may* produce an mbuf with more than a single link in the chain,
but HdlcOutput didn't know how to calculate the FCS :-(
o Make `struct fsm'::reqid a u_char, not an int.
This fix will prevent us from sending id `255' 2,000,000,000 times
before wrapping to `0' for another 2,000,000,000 sends :-/
o Bump the version number a little.
The end result: DEFLATE now works over an unreliable link layer.
I can txfr a 1.5Mb kernel over a (rather bad) null-modem
cable at an average of 21679 bytes per second using rcp.
Repeat after me: Don't test compression using a loopback ppp/tcp setup as
we never lose packets and therefore never have to reset!
o Allow a forth argument in ppp.secret, specifying a new
label. This gives control over which section of
ppp.link{up,down} is used based on the authenticated user.
o Support random address ranges in ppp.secret (not just in ppp.conf).
o Add a AUTHENTICATING INCOMING CONNECTIONS section to the man page.
o Add a bit more about DEFLATE in the man page.
o Fix the incorrect "you must specify a password in interactive
mode" bit of the manual.
o Space things in the man page consistently.
o Be more precice about where you can use MYADDR, HISADDR and INTERFACE
in the "add" command documentation.
not in -auto mode isn't a good idea, and that the
add should be done in ppp.linkup instead.
Change "add 0 0 HISADDR" to "add default HISADDR". It's
more intuitive.
interactive mode.
Use `netfd' in fcntl() and tc[gs]etattr() calls rather than
the hard coded descriptor 0.
Use _FILENO constants from unistd.h
This un-breaks things after my recent `close(0)' in interactive
mode.
Close STDIN_FILENO, and open _PATH_TTY O_RDONLY as `netfd'. This
has the effect of allowing `show route' to output more than about
a page of data (on FreeBSD, not OpenBSD....). I have no idea why,
except that it was a direct consequence of the tcsetattr() in
TtyCommandMode(). My previous fix (closing descriptor 0) `fixed'
this because all calls to tcsetattr() failed :-(
RTM_CHANGE if the RTM_ADD fails with an EEXIST.
Allow "delete! dst" (note the ``!'') to silently
fail if the RTM_DELETE fails with an ESRCH.
Also, make the ESRCH and EEXIST error conditions
more understandable to the casual observer.
Brian Somers