top of the hardware interrupt handlers. Apparently this is slightly
faster with the bit scanning instruction that looks these up - this set of
changes reverts the original change.
Reviewed by: bde
CPU code-named `M2'.
- Use the result of cpuid instruction instead of DIR to identify
6x86MX cpu. DIR0 and DIR1 are not documented in the data sheet, and
cpuid instruction is enabled at reset time.
- Add a function, init_6x86MX() to initialize 6x86MX cpu. It supports
CPU_SUSP_HLT and CPU_IORT options. It always sets NC1 (640K - 1M is
not cached.), and enables L1 cache in write-back mode.
- Fix typo in the comment in identblue().
Changes to pmap.c for lapic_t lapic && ioapic_t ioapic pointers,
currently equal to apic_base && io_apic_base, will stand alone with the
private page mapping.
apic.h has defines like:
#define lapic__id lapic->id
Once private pages and "known virtual addr" mapping of the APICs is
ready all 'lapic__XXX' will be changed to 'lapic.XXX', and the defines
will be removed.
Changes to smp.h for lapic_t lapic && ioapic_t ioapic pointers,
currently equal to apic_base && io_apic_base, will stand alone with the
private page mapping.
Adjust the data port address by adding the two low order bits of
the register number. The address port takes only a word address
(i.e. ignores the two low order bits written to it).
mode 1. Omission of this bit makes all config register accesses fail in
on recent chip sets ...
(The problem was reported and debug output provided by: Steve Passe)
- vector.s <- stub called by i386/exception.s
- icu_vector.s <- UP
- apic_vector.s <- SMP
Split icu.s into UP and SMP specific files:
- ipl.s <- stub called by i386/exception.s (formerly icu.s)
- icu_ipl.s <- UP
- apic_ipl.s <- SMP
This was done in preparation for massive changes to the SMP INTerrupt
mechanisms. More fine tuning, such as merging ipl.s into exception.s,
may be appropriate.
reality. There will be a new call interface, but for now the file
pci_compat.c (which is to be deleted, after all drivers are converted)
provides an emulation of the old PCI bus driver functions. The only
change that might be visible to drivers is, that the type pcici_t
(which had been meant to be just a handle, whose exact definition
should not be relied on), has been converted into a pcicfgregs* .
The Tekram AMD SCSI driver bogusly relied on the definition of pcici_t
and has been converted to just call the PCI drivers functions to access
configuration space register, instead of inventing its own ...
This code is by no means complete, but assumed to be fully operational,
and brings the official code base more in line with my development code.
A new generic device descriptor data type has to be agreed on. The PCI
code will then use that data type to provide new functionality:
1) userconfig support
2) "wired" PCI devices
3) conflicts checking against ISA/EISA
4) maps will depend on the command register enable bits
5) PCI to Anything bridges can be defined as devices,
and are probed like any "standard" PCI device.
The following features are currently missing, but will be added back,
soon:
1) unknown device probe message
2) suppression of "mirrored" devices caused by ancient, broken chip-sets
This code relies on generic shared interrupt support just commited to
kern_intr.c (plus the modifications of isa.c and isa_device.h).
be (eventually) architecture independent. It provides an emulation
of the ISA interrupt registration function register_intr(), but that
function does no longer manipulated the interrupt controller and
interrupt descriptor table, but calls the architecture dependent
function setup_icu() for that purpose.
After the ISA/EISA bus code has been modified to directly call the new
interrupt registartion functions (intr_create() and intr_connect()),
the emulation of register_intr() should be dropped.
The C level interrupt handler function should take a (void*) argument,
and the function pointer type (inthand2_t) should defined in some other
place than isa_device.h.
This commit is a pre-requisite for the removal of the PCI specific shared
interrupt code.
Reviewed by: dfr,bde
This is now the default, it delays most of the MP startup to the function
machdep.c:cpu_startup(). It should be possible to move the 2 functions
found there (mp_start() & mp_announce()) even further down the path once
we know exactly where that should be...
Help from: Peter Wemm <peter@spinner.dialix.com.au>
- The 1st (preparse_mp_table()) counts the number of cpus, busses, etc. and
records the LOCAL and IO APIC addresses.
- The 2nd pass (parse_mp_table()) does the actual parsing of info and recording
into the incore MP table.
This will allow us to defer the 2nd pass untill malloc() & private pages
are available (but thats for another day!).
panic( "xxxxx\n" );
to:
printf( "xxxxx\n" );
panic( "\n" );
For some as yet undetermined reason the argument to panic() is often NOT
printed, and the system sometimes hangs before reaching the panic printout.
So we hopefully at least print some useful info before the hang, as oppossed to
leaving the user clueless as to what has happened.
Remove "setdefs.h" and arrange to generate it automatically at
ELF kernel build time.
"gensetdefs.c" is a utility which scans a set of ELF object files
and outputs a line ``DEFINE_SET(name, length);'' for each linker
set that it finds. When generating an ELF kernel, this is run just
before the final link to generate "setdefs.h".
Remove the init_sets() function from "setdef0.c", and its call from
"machdep.c". Since "gensetdefs.c" calculates the length of each
set, it is no longer necessary in an ELF kernel to count the set
elements at kernel initialization time. Also remove "set_of_sets"
which was used for this purpose.
Link "setdef0" and "setdef1" into the kernel only if building for
ELF. Since init_sets() is no longer used, there is no need to link
them into an a.out kernel.
all uses of it with the equivalent calls to setbits().
This change incidentally eliminates a problem building ELF kernels
that was caused by SETBITS.
Reviewed by: fsmp, peter
Submitted by: bde
to fill in the nfs_diskless structure, at the cost of some kernel
bloat. The advantage is that this code works on a wider range of
network adapters than netboot. Several new kernel options are
documented in LINT.
Obtained from: parts of the code comes from NetBSD.
was stale.
Fixed initialization of gdt[] for the BDE_DEBUGGER case. APM entries
clobbered debugger entries if the debugger was loaded (APM is incompatible
with BDE_DEBUGGER) and unused entries were garbage if the debugger wasn't
loaded.
(eg: above 0xffc00000). Programs using /dev/kmem are implicitly racing
the kernel, and can get right up high in memory. I've been running
these for some time now, but with printfs. It's saved two panics at
least that I can remember.
md_regs being struct trapframe *. Do a npxsave() if needed and copy the
pcb rather than use the increasingly defunct savectx(). Copy %edi and
%ebp explicitly.
Submitted by: bde
XXX npxproc could be declared in npx.h so the externs with smp fruit
are not needed.
Remove TF_REGP() macro and use. The original reason (address space
problems due to having UPAGES in mapped into user space) is gone. It
looks cleaner without it.
Peter Wemm
KATO Takenori
Steve Passe
Stefan Eßer
Philippe Charnier
John Polstra
Tor Egge
Bruce Evans