> <sys/param.h> doesn't include <sys/time.h>
>
> I removed the NAPM check since it's wasteful to check twice. apmprobe()
> checks the unit number, and that's the right check.
Submitted by: bde
swapgeneric.c hasn't had anything to do with swapping for some time.
It just makes the -a boot option actually work, and breaks the static
configuration of rootdev and dumpdev. It should be reorganized to
only support -a.
etc..), plus add a better display suspend function.
- Changed the Copyright's to reflect the new 'jp.FreeBSD.org' email
address.
Submitted by: nate & HOSOKAWA, Tatsumi <hosokawa@jp.FreeBSD.org>
- the operands for bt, bts, arpl and `enter' were reversed.
- btr was reported as bts (with the correct operand order).
- cmpxchg was misplaced. It was misplaced differently in the
comments. It is misplaced differently again in the i486 manual.
I put it where the i586 manual and gas say it is.
- fucompp was misplaced.
- the rr table for(s) some versions of fstp, fcom and fcomp was non-null.
This caused some invalid opcodes to be reported as "" instead of as
"<bad instruction>".
- the word and long versions of the fi* instructions were reversed.
- aaa and daa were reversed.
Fixed bugs involving unusual operand sizes:
- 32-bit registers weren't always forced for bswap or for moves to and
from special registers.
- the operand sizes weren't reported for [l]call or [l]jmp.
- displacements weren't truncated mod 2^16 when the operand size was
16-bit.
- too-large displacements and offsets were fetched, and too-large
offsets were reported, when the operand size was 16-bit.
- sign extended immediate bytes were extended too far when the operand
size was 16-bit.
Fixed bugs involving usual operand sizes:
- 8-bit source registers weren't forced for mov[sz]b[wl].
- 16-bit source registers weren't forced for mov[sz]w[wl].
- immediate bytes were sometimes reported as sign extended even for
byte operations. Same for immediate words in word operations.
- the immediate byte was not reported as sign extended for `push'.
Finished Pentium support:
- cpuid, cmpxchg8b and rsm were missing.
Finished i287 support:
- fneni, fndisi and fsetpm were missing. These are harmless nops on
later FPUs.
Improvements:
- report invalid opcodes 0xd6 and 0xf1 using .byte. They are special
in not causing invalid operand exceptions when executed.
- report the immediate byte for unusual aam and aad instuctions.
Immediate bytes other than 0x0a always worked and are documented to
work on Pentiums.
wdparams from short into u_short. If wdp_cylinders is short, it
overflows and cause serious sign extension bug when large IDE HDD is
used. These members are only used for initialization of u_long
variables in both 3.0-current and RELENG_2_2 branch.
I believe this should be in 2.2.
Reviewed by: Bruce Evans <bde@zeta.org.au>
This code was sent to me by Bruce Evans, and seems to fix some
possible kernel panic in case of an execution error. It did not
cause any problems on my system, but I did never observe the
problem this patch is supposed to fix, anyway.
This patch is a NOP, unless the kernel is built with "options
USER_LDT", and doesn't affect the GENERIC kernel for this reason.
I want to have it in 2.2: it fixes a bug ...
Submitted by: bde
taken from the voxware-3.5 distribution. Also some changes to the SB
and MPU IRQs to reflect more common/default settings.
Submitted-By: Brian Campbell <brianc@netrover.com>
at device attach time, instead of allocating and freeing buffers as
necessary. But he or she forgot to remove the line that invalidated
the buffer when the device is closed. Therefore, after using the
device for the first time, the buffer was incorrectly invalidated and
that caused a page fault on the second, and subsequent uses.
Closes PR # kern/2319: Using Genius GS-4500 scanner...
Submitted by: jmrueda@diatel.upm.es (Javier Martmn Rueda)
also implies VM_PROT_EXEC. We support it that way for now,
since the break system call by default gives VM_PROT_ALL. Now
we have a better chance of coalesing map entries when mixing
mmap/break type operations. This was contributing to excessive
numbers of map entries on the modula-3 runtime system. The
problem is still not "solved", but the situation makes more
sense.
Eventually, when we work on architectures where VM_PROT_READ
is orthogonal to VM_PROT_EXEC, we will have to visit this
issue carefully (esp. regarding security issues.)
is still broken - it doesn't restore the floating point state.
2.2-BETA users should disable it using npx0 flags 0x04 the same as
2.2-ALPHA users should have.
Closes PR # kern/1065.
While i was at it, also reject IO requests that are not an integer
multiple of the device blocksize.
Submitted by: vak@crox.net.kiae.su (Serge V.Vakulenko)
Confirmed by: Georg-W. Koltermann (gwk@cray.com)
workings of #error in particular. He also broke the 2.2 build with this
change, leading me to wonder whether or not the changes were ever even
tested. Folks, I'm happy to see people work directly on 2.2 like
this and will continue to encourage Nate to make direct commits, but
please TEST before committing! I think that's a more than reasonable
prerequisite, and this code could never have worked at all, leading me to
believe that Nate skipped this most basic of steps.
Don't allow people to use the 'dedicated' drivers at the same time as
the generic support code, as it can cause all sorts of problems
including kernel crashes.
[ definite 2.2 material ]
Broke locking on named pipes in the same way as locking on non-vnodes
(wrong errno). This will be fixed later.
The fix involves negative logic. Named pipes are now distinguished from
other types of files with vnodes, and there is additional code to handle
vnodes and named pipes in the same way only where that makes sense (not
for lseek, locking or TIOCSCTTY).
This makes unexpected faults (in an interrupt handler) more likely
to crash properly. It could be done even better (more robustly and
more efficiently) using lazy fault handling.
They were garbage that happened to be 0 in many cases. (real_to_prot()
happens to leave the value of the real-mode %cr0 in %eax and the
memory-size BIOS calls usually don't touch the upper bits of %eax.
The upper 16 bits of %cr0 are usually 0 at boot time, at least on
486's.
Should be in 2.2.
configure() where it always belonged. It was originally slightly
misplaced after configure(). Rev.138 left it completely misplaced
before the DEVFS, DRIVERS and CONFIGURE sysinits by not moving it
together with configure().
Restored the printing of bootinfo.bi_n_bios_used now that it can
be nonzero.
EISA slots to probe. This is mainly intended to allow installing the
system on an HP Netserver with an on-board AIC7xxx EISA SCSI
controller, that is sitting on EISA slot # 11.
Documentation updates explaining this hack will follow shortly.
Note that this can go away again as soon as the EISA device probing
is more intelligent about the address space clash with the PCI address
space.
2.2 candidate.
Not objected by: freebsd-core :)
to TAILQs. Fix places which referenced these for no good reason
that I can see (the references remain, but were fixed to compile
again; they are still questionable).
the profiling level in config and decide what to do in makefiles.
Makefile.i386:
Align functions to 16-byte boundaries if profiling is enabled. This
will allow a fourfold reduction in the size of the profiling buffers.
I've added an installation from optical disk drive facility.
This enables FreeBSD to be installed from an optical disk, which
may be formatted in "super floppy" style or sliced into MSDOS-FS
and UFS partitions.
Note: ncr.c should be reviewed by Stefan Esser <se@freebsd.org>
and cd.c by Joerg Wunsch <joerg@freebsd.org> before bringing this
into 2.2.
Submitted-By: Shunsuke Akiyama <akiyama@kme.mei.co.jp>
makerom checksum check calculation was a no-op
nb8390.c had a bug which caused packet_len to be incorrect
for packets which wrapped in the buffer.
Submitted by: Linux developers (I lost the email with their names)
partition is 0, which is outside the slice unless the disk is
dangerously dedicated. There is little error checking later, and
following garbage metadata outside the slice usually caused crashes,
Empty 'a' partitions are fairly easy to create by cloning the label
for the whole disk.
Fixed a missing newline in a related error message.
type to be int so that errors can be returned.
2) Use the new SIOCSIFMTU ether_ioctl support in the few drivers that are
using ether_ioctl().
3) In if_fxp.c: treat if_bpf as a token, not as a pointer. Don't bother
testing for FXP_NTXSEG being reached in fxp_start()...just check for
non-NULL 'm'. Change fxp_ioctl() to use ether_ioctl().
ACTUALLY_LKM_NOT_KERNEL until the real fix comes through. Whatever
flag that is used to indicate building LKMs will have be be substituted
in the future. This allows proper selection of the usage of the
efficient, single instruction in the kernel, but alas, doesn't allow
for use in userland or LKMs :-(. Them's the breaks!!!
with one of the following (I486_CPU,I586_CPU,I686_CPU) so it can take
advantage of the very quick bswap insn. This keeps LKMs from being
built to take advantage of the insn, but also makes sure that the LKMs
can be run on all CPUs. (The LKMs don't pick up the CPU options :-( ).
function ed_attach_NE2000_pci() in if_ed.c passes
an uninitialized block of memory (got with malloc())
to ed_attach. This prevents a proper initialization
of the device descriptor and in my case causes a panic
during the probe, while printing out device info.
Reviewed by: phk
Submitted by: Luigi Rizzo <luigi@iet.unipi.it>
list of IP setsockopts the Linux emulator recognizes.
Explicitly disallow IP_HDRINCL since Linux's handling of
raw output is different than BSD's.
Closes PR#kern/2111.
Submitted by: y-nakaga@ccs.mt.nec.co.jp (Yoshihisa NAKAGAWA)
1. All the suggestions earlier made by Bruce: renaming some symbols,
stricter error checking, removing redundant code, etc.
2. The `psm' driver preserves the default counter resolution and
report rate, whatever they are after reset. (Based on reports and
suggestion from Nate and Rob Bolin).
3. The `psm' driver now does not check the so-called sync. bit in the
first byte of the data packet by default, so that the tapping feature
of ALPUS GlidePoint works (based on reports from Louis Mamakos). I
tested the code with ALPUS Desktop GlidePoint (M/N GP101) and found
no problem; tapping worked. It appears ALPUS produces several models
of GlidePoint. I hope the other models are OK too.
The check code can still be activated by defining the PSM_CHECKSYNC
option in the config file. (The bit checking slightly reduces, if not
completely eliminates, weird mouse behavior cased by unsynchronized
mouse data packets. It also helps us to detect if the mouse interrupt
can ever be lost. But, well, if there are devices which cannot be
supported this way...)
4. The `psm' driver does not include the protocol emulation code by
default. The code can still be compiled in if the PSM_EMULATION option
is specified in the config file. Louis Mamakos suggests the emulation
code is putting too much in the kernel, and `moused' works well.
I will think about this later and decide if the entire emulation
code should be removed.
5. And, of course, the fix in `scprobe()' from Bruce to cure the
UserConfig problem. My code in `kbdio.c' is slightly different from
his patch, but has the same effect. There still is a possibility that
`scprobe()' gets confused, if, for whatever reasons, the user holds
down a key for very long time during the boot process. But we cannot
cope with everything, can we?
Submitted by: Kazutaka YOKOTA (yokota@zodiac.mech.utsunomiya-u.ac.jp)
decrease the size of buffer_map to approx 2/3 of what it used to be
(buffer_map can be smaller now.) The original commit of these changes
increased the size of buffer_map to the point where the system would
not boot on large systems -- now large systems with large caches will
have even less problems than before.
are always together with Framing Errors and they were incorrectly
treated as FE's and discarded.
Reorganized the BREAK/FE/PE tests.
Found by: NIST-PCTS
with sio devices (not perfectly, since there is no way to flush the tx
holding register on 8250-16450's. I'm not sure if resetting the fifos
flushes the tx shift register).
Reminded by: NIST-PCTS
is completely empty. There is no interrupt for output completion, so
poll for it every 10 ms after output is nearly complete. Now ttywait()
works right.
Reminded by: NIST-PCTS
registers.) Also clean up some namespace pollution, and remove
gcc-1 support (nothing really works with it anymore anyway.)
Submitted by: Bruce Evans <bde@freebsd.org> and me.
consistent stack frame in fastmove() so that only one new fault handler
is necessary.
Should be in 2.2. Harmless until the i586 versions are reenabled.
Per Wayne Scott of Intel, the old sequence took 20cycles!!! on a P6.
Another nice side-benefit is that the kernel is about 3K smaller!!!
Submitted by: Wayne Scott <wscott@ichips.intel.com>
the keyboard IO port definitions from <machine/console.h>.
Note: I do not have a machine available to test this yet, I sent this
for review to several people who have not replied.
This is also totally busted in 2.2, which has half of the syscons/psm/kbdio
changes in it. This really desperately needs to be tested and fixed
in 2.2 as well.
SCBs in response to a busfree.
When re-queueing an SCB that returned with QUEUE FULL status, reset its timeout.
Ensure that aborted SCBs have an error code set in there xs before it gets
passed back up with scsi_done.
Fix a few KNF nits.
uses /usr/include/sys/*, which may point to a different build tree. I'm
not sure that this is necessary, but there was a question mark over what
/usr/include/sys points to when building the "user mode" binaries in the
kernel code, especially when building the smp tree.
I suspect that the "right" line here is to use ${INCLUDES}, but that
causes warnings about unused static inline functions in stdio.h and ctype.h
The 'getchar' function in syscons (sccngetc) is used by UserConfig to
get keyboard input from the user. When it was modified to use the
shared keyboard port routines it used the port passed in during the
probe routine. Since the probe routine was not yet called, the port was
set to 0, which is obviously not going to work.
Pre-initialize sc_port to IO_KBD which is really a kludge, but it's how
the previous driver did it's job.
Found by: remote GDB
substantially increasing buffer space. Specifically, we double
the number of buffers, but allocate only half the amount of memory
per buffer. Note that VDIR files aren't cached unless instantiated
in a buffer. This will significantly improve caching.
do reset it from the QOUTCNT register inside a pause/unpause. This now happens
once per command complete interrupt in the paging case (one interrupt can be
for multiple completed commands). I may introduce a counter and do a lazy
update in the future, similar to what is done with the QINCNT.
Enhance the QUEUE FULL condition handling so that the number of openings will
be reduced. This has become more important now that the driver is faster.
This code really belongs in the gerneric SCSI layer, as will be the case once
3.0 gets the code from the 'SCSI' branch.
Add some #if 0'd out trace code I've been using to help debug sequencer
problems.
Fix the SCB paging problem that I was seeing. This was only on my 7850
controller and stems from the fact that its QINFIFO can only handle 3bit
SCB identifiers. This means that you can only have 8 transactions open at
a time with the current paging scheme to these controllers. The code added
to enforce this is generic in that it tests for the number of relevent bits
that the QINFIFO can store and adjusts the max accordingly. It may be possible
to come up with a scheme that allows for more than 8 commands at a time, but
I don't know that it is worth the effort simply to fix a low end card. The
aic7880 still can do 255.
This problem may be related to what Andrey was seeing since I don't have n
aic7770 rev E chip here to test on, but as soon as someone probes one of these
cards with this new code, the dmesg output will tell the whole story.
aic7xxx cards failing on certain motherboards, reverse the logic used to
control this feature. AHC_FORCE_PIO is replaced with AHC_ALLOW_MEMIO.
GENERIC no longer needs to specify the AHC_FORCE_PIO option since this is
the default.
user supplies a bad address, because they push a lot of stuff that the
fault handler doesn't know about onto the stack. This has been broken
for more than half a year despite being tested for almost half a year
in -current.
synthesizer. The utilities for this will appear as port submissions soon
afterwards, according to the submitter.
Submitted-By: Randall Hopper <rhh@ct.picker.com>
Written-By: Takashi Iwai <iwai@dragon.mm.t.u-tokyo.ac.jp>
with the copyright stuff fixed so soon (this should be merged into 2.2 when
you have a chance, Poul).
This is the new AWE32 driver, with support for the AWE32's fancy MIDI
synthesizer. The utilities for this will appear as port submissions soon
afterwards, according to the submitter.
Submitted-By: Randall Hopper <rhh@ct.picker.com>
Written-By: Takashi Iwai <iwai@dragon.mm.t.u-tokyo.ac.jp>
routines. An older version of this was tested successfully on all of my
systems with PS/2 mice. This was brought in without testing because it
is necessary due to the previously committed syscons changes.
Submitted by: Kazutaka Yokota <yokota@zodiac.mech.utsunomiya-u.ac.jp>
syscons and psm, curtesy Kazutaka Yokota with minor changes by
me. This contains an update of the psm driver as well.
This also fixes the breakage that I introduced to the psm driver by
making syscons poll for keyboard events in the atempt to fix the
hanging keyboard problem.
It works perfectly for me, and I'd like to hear from all that
have had keyboard/ps/2 mouse problems if this is the cure...
Submitted by: Kazutaka YOKOTA (yokota@zodiac.mech.utsunomiya-u.ac.jp)
wdreg.h: Delete wd_ctlr macro. PC98 version of wd.c treats it as a
variable.
GENERIC98: Delete ep0 entry. Current ep driver write I/O port 0x100.
This clobbers ICW of i8259, because upper 8bits of address line is not
masked on mother board.
if_fe.c: Merge from revision 1.18 of sys/i386/isa/if_fe.c.
pc98.c: Globalize dmapageport, because SCSI driver use this
variable.
wd82371.c: Yet another merge.
These are 2.2 candidates.
Submitted by: The FreeBSD(98) Development Team
almost complete control over RTS (control of its initial value is still
missing).
This fixes PR 1644 for sio.
The author of PR 1644 wants it in 2.1.6 and 2.2. This may be safe since
the complications are only in rarely used cases that I hope I've covered.
sys/pc98/i386/machdep.c: sync with i386/i386/machdep.c
sys/pc98/conf/options.pc98: sync with i386/conf/options.i386
sys/i386/isa/sound: DMA auto initialize mode support for PC98.
contributed by: Akio Morita <amorita@bird.scphys.kyoto-u.ac.jp>
Definite 2.2 material, I believe.
Submitted by: The FreeBSD (98) Development Team
one too small for (hex) 12345678 and 4 too small for -1234567890. Large
values can be created by config and userconfig although not (previously)
by visual userconfig.
Fixed a sign extension bug for backspacing on "negative" hex values in
editval().
Increased field width and range for `flags' so that all possible values
can be displayed and edited.
actually harmless.
2. Fixed code to match comment in scintr().
3. Don't allow even root to take control of the machine when securelevel > 0.
I've secured the accesses to PSL_IOPL in all drivers and asked pst to
review it, but he seems to be busy. Write access to /dev/kmem and
other critival devices currently leaks across raisings of securelevel
via open fd's, so there may as well be a similar leak for PSL_IOPL.
4. (Most important.) Don't corrupt memory beyond the screen buffers if
the cursor happens to be off the 80x25 screen when syscons starts.
5. Fix console cursor update (not perfect yet).
Submitted by: bruce
~
getting the same behavior using the flags, which can be done inside of
UserConfig. (Also document other syscons flags which were previously
undocumented).
Requested by: bde
negative-logic flags (flags 0x01 and 0x02 for npx0, defaulting to unset = on).
This changes the default from off to on. The options have been in current
for several months with no problems reported.
Added a boot-time negative-logic flag for the old I5886_FAST_BCOPY option
which went away too soon (flag 0x04 for npx0, defaulting to unset = on).
Added a boot-time way to set the memory size (iosiz in config, iosize in
userconfig for npx0).
LINT:
Removed old options. Documented npx0's flags and iosiz.
options.i386:
Removed old options.
identcpu.c:
Don't set the function pointers here. Setting them has to be delayed
until after userconfig has had a chance to disable them and until after
a good npx0 has been detected.
machdep.c:
Use npx0's iosize instead of MAXMEM if it is nonzero.
support.s:
Added vectors and glue code for copyin() and copyout().
Fixed ifdefs for i586_bzero().
Added ifdefs for i586_bcopy().
npx.c:
Set the function pointers here.
Clear hw_float when an npx exists but is too broken to use.
Restored style from a year or three ago in npxattach().
for get_diskinfo(), whose BIOS call sets %es:%edi in some cases, although
most documentation says that it doesn't change %edi in the cases that
happened to matter (for hard disks).
This shall be in 2.1.6 and 2.2.
Submitted by: Tor.Egge@idt.ntnu.no
(except I kept the unnecessary preservation of %edx and %ecx)
are adding new drivers...) to match, as best I can tell, majors.i386.
Improve behaviour when attempting to save changes for devices that should
not be changeable. Now correclty avoids non-device items, PCI devices and
devices with no isa_device structure.
Submitted by: (observations from) joerg, bde
uses one or the other. This required some changes to the ahc_reset()
function, and how early the probes had to allocate their softc.
Turn the AHC_IN/OUT* macros into inline functions and lowercase their names
to indicate this change. Geting AHC_OUTSB to work as a macro doing
conditional memory mapped I/O would have been too gross.
Stop setting STPWEN in the main driver and let the PCI front end do it
instead. It knows better.
Add the clearing of the QOUTQCNT variable during command complete processing
in the SCB paging case.
Go back to doing unconditional retries for the QUEUE FULL status condition.
This is really a kludge, but the code to handle it properly is on the SCSI
branch and will not make it into 2.2.
uses one or the other. This required some changes to the ahc_reset()
function, and how early the probes had to allocate their softc.
Turn the AHC_IN/OUT* macros into inline functions and lowercase their names
to indicate this change. Geting AHC_OUTSB to work as a macro doing
conditional memory mapped I/O would have been too gross.
This allows the user to add modify syscons's configuration flags using
UserConfig that will allow older/quirky hardware (most notably older IBM
ThinkPad laptops) to work with the standard boot kernel.
Inspired by: The Nomads
if I586_CPU is defined. Note there is a runtime check so the code
won't be run for non-Pentium CPUs anyway.
2.2 candidate, this code has been tested for almost half year in -current.
handlers if interrupts are nested more than a few (3) deep. This
only reduces the maximum nesting level by 1 with the standard
drivers unless there is a related bug somewhere, but can't hurt
much (the worst case is returning to hoggish interrupt handler like
wdintr(), but such interrupt handlers hurt anyway).
Fixed a previously harmless race incrementing the interrupt nesting
level.
This should be in 2.1.6 and 2.2.
hardware interrupt counts add up to the total. Previously, software
interrupts generated by splz() were counted in the total. These
software interrupts seem to be very rare - there have apparently been
0 of them on freefall among the last 352448857 interrupts.
will be renamed.
Fixed comments about unsupported network protocols.
ncr0 is a controller, not a device. This make no difference.
Added undocumented options DEVFS_ROOT, I586_CTR_GUPROF and I586_PMC_GUPROF.
Sorted undocumented options.
it automatically. The AHC_FORCE_PIO option wasn't having any effect because
the PCI probe code didn't include this file.
Fix some problems with the new sync and wide negotiation code. First off,
go back to async transfers by using a message reject again. The SCSI II and
III spec indicate that if a target's response to an initiater does not suit
(i.e. its too low), then performing a message reject is the appropriate
response. If, on the other hand, the initiator begins the negotiation and
we want to go async, we will send back an SDTR message with a 0 period and
offset.
Also fix a really bad negotiation problem caused by a missing "break". This
would usually hit people that had "smart" wide devices that immediately
attempt sync negotiation after a successful wide negotiation.
2.2 Candidate.
or list items which may look like devices but which don't have an
isa_device structure attached to them.
This _shouldn't_ be possible, but it appears to have been
observed-by: Joerg
3COM 3C590 Etherlink III PCI,
3COM 3C595 Fast Etherlink PCI,
3COM 3C592 Etherlink III EISA,
3COM 3C590 Fast Etherlink EISA,
3COM 3C900 Etherlink XL PCI and
3COM 3C905 Fast Etherlink XL PCI.
This driver is based on OpenBSD's driver. I modified it to run under FreeBSd
and made it actually work usefully.
Afterwards, nao@tom-yam.or.jp (HAMADA Naoki) added EISA support as well as
early support for 3C900 Etherlink XL PCI and 3C905 Fast Etherlink XL PCI.
He also split up the driver in a bus independant and bus dependant parts.
Especially the 3c59X support should be pretty stable now.
Submitted by: partly nao@tom-yam.or.jp (HAMADA Naoki)
Obtained from:partly OpenBSD
mappings with mlock. This problem only occurred because of the
quick unmap code not respecting the wired-ness of pages in the
process. In the future, we need to eliminate the dependency
intrinsic to the design of the code that wired pages actually
be mapped. It is kind-of bogus not to have wired pages mapped,
but it is also a weakness for the code to fall flat because
of a missing page.
This show fix a problem that Tor Egge has been having, and also
should be included into 2.2-RELEASE.
appearance of this bug was the malfunctioning -M option in GNU tar (it
worked only by explicitly specifying -L).
Reviewed by: bde, and partially corrected accoring to his comments
Candidate for 2.2, IMHO even for 2.1.6.
changes to the keyboard code in pcvt, this update_led() very often
caused pcvt to hang early at boot time.
(Eventually, a better solution should be found, but the simple
omission serves well as a workaround for something that is actually a
show-stopper class problem.)
Candidate for 2.2.
(1) deleted #if 0
pc98/pc98/mse.c
(2) hold per-unit I/O ports in ed_softc
pc98/pc98/if_ed.c
pc98/pc98/if_ed98.h
(3) merge more files by segregating changes into headers.
new file (moved from pc98/pc98):
i386/isa/aic_98.h
deleted:
well, it's already in the commit message so I won't repeat the
long list here ;)
Submitted by: The FreeBSD(98) Development Team
(1) Add #ifdef PC98:
sys/pc98/boot/biosboot/boot2.S
(2) Fix bug that made it impossible to boot from sd's other than unit 0:
sys/pc98/boot/biosboot/sys.c
(3) Delete redundant $Id$:
sys/pc98/pc98/clock.c (reject$B$5$l$k$+$b$7$l$J$$(B)
(4) unt -> u_int:
sys/pc98/pc98/if_ed.c
(5) Add support for rebooting by the hot-key sequence:
sys/pc98/pc98/kbdtables.h
(6) Display now looks like PC/AT version:
sys/pc98/pc98/npx.c
(7) Change comment to match that of PC/AT version:
sys/pc98/pc98/pc98.c
(8) Add function prototypes:
sys/pc98/pc98/pc98_machdep.c
(9) Include PC98 headers:
sys/pc98/pc98/sound/adlib_card.c
sys/pc98/pc98/sound/audio.c
sys/pc98/pc98/sound/dev_table.c
sys/pc98/pc98/sound/dmabuf.c
sys/pc98/pc98/sound/midi_synth.c
sys/pc98/pc98/sound/midibuf.c
sys/pc98/pc98/sound/opl3.c
sys/pc98/pc98/sound/oatmgr.c
sys/pc98/pc98/sound/sb16_dsp.c
sys/pc98/pc98/sound/sb16_midi.c
sys/pc98/pc98/sound/sb_card.c
sys/pc98/pc98/sound/sb_dsp.c
sys/pc98/pc98/sound/sb_midi.c
sys/pc98/pc98/sound/sb_mixer.c
sys/pc98/pc98/sound/sequencer.c
sys/pc98/pc98/sound/sound_config.h
sys/pc98/pc98/sound/sound_switch.c
sys/pc98/pc98/sound/soundcard.c
sys/pc98/pc98/sound/sys_timer.c
(10) Merge in PC98 changes:
sys/i386/isa/sound/os.h
(11) Deleted as result of 9. and 10. above:
sys/pc98/pc98/sound/ad1848_mixer.h
sys/pc98/pc98/sound/aedsp16.c
sys/pc98/pc98/sound/coproc.h
sys/pc98/pc98/sound/finetune.h
sys/pc98/pc98/sound/gus_hw.h
sys/pc98/pc98/sound/gus_linearvol.h
sys/pc98/pc98/sound/hex2hex.h
sys/pc98/pc98/sound/mad16.h
sys/pc98/pc98/sound/midi_ctrl.h
sys/pc98/pc98/sound/midi_synth.h
sys/pc98/pc98/sound/opl3.h
sys/pc98/pc98/sound/os.h
sys/pc98/pc98/sound/pas.h
sys/pc98/pc98/sound/sb_mixer.h
sys/pc98/pc98/sound/soundvers.h
sys/pc98/pc98/sound/tuning.h
Submitted by: The FreeBSD(98) Development Team
Check that a received packet isn't longer than MCLBYTES. This will
sometimes happen if a cable is plugged into or removed from a live
system.
Try to cater better for early receive interrupts.
This involves expanding the support of the SEEPROM routines to deal with
the larger SEEPROMs on these cards and providing a mechanism to share
SCB arrays between multiple controllers.
Most of the 398X support came from Dan Eischer.
ahc_data -> ahc_softc
Clean up some more type bogons I missed from the last pass.
Be more clear when handing the NO_MATCH condition. NO_MATCH can also
happen when the sequencer encounters an SCB we've asked to be aborted.
AHC_FORCE_PIO - This forces the driver to use PIO even on systems that
say they have memory mapped the controller's registers. This
seems to fix Ken Lam's problems. I've also placed this option
in the GENERIC kernel file so that we are guaranteed to install
even on these flakey machines.
AHC_SHARE_SCBS - This option attempts to share the external SCB SRAM on
the 398X controllers allowing a totoll of 255 non-paged SCBs.
This doesn't work quite yet, so this option is mostly here to
help 398X owners to experiment and give me feedback until this
works properly.
TIMER_FREQ.
Fixed missing splx() in scrn_timer(). The bug was harmless because of the
undocumented behaviour that the ipl is automatically restored for timeout
functions (see softclock()). Perhaps we should depend on this behaviour.
Fixed the ddb fix in rev.1.176. The in_debugger flag was no use because
it only works when the debugger is entered via the keyboard hotkey. The
debugger may be entered for breakpoints and traps, and the console putc
routine has no way of knowing when it was, so the console putc routine
must (almost?) always remove the cursor image.
Not fixed: console switching in ddb doesn't work (ISTR it working), and
console 0 shouldn't be switched to for the debugger hotkey unless console
0 is /dev/console.
Fixed side effects from calling add_keyboard_randomness() in the console
getc routine by not calling it. add_keyboard_randomness() currently
always reenables interrupts on 386's and 486's. This is very bad if the
console getc routine is called from the debugger and the debugger was
entered with interrupts disabled.
Fixed preservation of initial screen and now-bogus comment about it. It
was broken by setting the initial scr_buf to `buffer' instead of Crtat.
`buffer' was full of nulls and the first scroll cleared everything above
the things written through syscons.
Submitted by: bruce (bde@freebsd.org)
Nate Williams
Bruce Evans
KATO Takenori
Stefan Eßer
Jordan K. Hubbard
Joerg Wunsch
John Dyson
Andrey A. Chernov
Poul-Henning Kamp
Alexander Langer
Steven Wallace
Mike Smith
David Greenman
Peter Wemm
Garrett Wollman
Martin Renters
Søren Schmidt
Satoshi Asami
Justin T. Gibbs
Bill Fenner
Sujal Patel
Guido van Rooij
Paul Traina
John Hay
Julian Elischer
Warner Losh