problems reported recently (the rtentry pointer in the dummynet
queue was not initialized in all cases, resulting in spurious
rt_refcnt decreases in the lucky cases, and memory trashing in
other cases.
problems in case a wrong option was given previously, and no option
is given to the next command.
PR: kern/9371
Submitted by: "Daniel C. Sobral" <dcs@newsguy.com>
Note no matching commit for the Alpha, as the alpha boot0 stage does
not have the ability to prompt for user input.
PR: kern/9406
Submitted by: "Daniel C. Sobral" <dcs@newsguy.com>
capabilities, but should be a good start... Well, sort of.
It can handle W*ndows 256 color BMP file. (Other color depth probably
won't work.) The size of the image must be 320x200 or less. *sigh*
keyboard and video card drivers.
Because of the changes, you are required to update your kernel
configuration file now!
The files in sys/dev/syscons are still i386-specific (but less so than
before), and won't compile for alpha and PC98 yet.
syscons still directly accesses the video card registers here and
there; this will be rectified in the later stages.
performance and reliability a little. There was a condition before
where transmission would stall during periods of heavy traffic
exchange between two hosts. Also set the 'want interrupt' bit in
receive descriptor control words.
Move the relocated boot1 and arg transfer space from 0x600/0x800 to
0x700/0x900. In theory this should make no difference, apart from the fact
that Buslogic controllers happen to use a few bytes at 0x600 for some sort
of scratch space for it's int 0x13 hook (!!!), causing the machine to crash
badly when the boot2 code makes it's callbacks into boot1 for disk IO.
Submitted by: Robert Nordier <rnordier@freebsd.org>
+ ECP parallel port chipset FIFO detection
+ DMA+FIFO parallel I/O handled as chipset specific
+ nlpt updated in order to use the above enhanced parallel I/O.
Use 'lptcontrol -e' to use enhanced I/O
+ Various options documented in LINT
+ Full IEEE1284 NIBBLE and BYTE modes support. See ppbus(4) for
an overview of the IEEE1284 standard
+ Detection of PnP parallel devices at boot
+ Read capability added to nlpt driver to get IEEE1284 compliant
printer status with a simple 'cat /dev/lpt0'
+ IEEE1284 peripheral emulation added to BYTE mode. Two computers
may dialog according to IEEE1284 signaling method.
See PERIPH_1284 option and /sys/dev/ppbus/ppi.c
All this code is supposed to provide basic functions for IEEE1284 programming.
ppi.c and nlpt.c may act as examples.
It was nay'ed before committing on the grounds that this is not
the way to do it, and has been decided as such several times in
the past.
There is not point in loading gobs of ascii into the kernel when
the only use of that ascii is presentation to the user.
Next thing we'd be adding all section 4 man pages to the loaded
kernel as well.
The argument about KLD's is bogus, klds can store a file in
/usr/share/doc/sysctl/dev/foo/thisvar.txt with a description and
sysctl or other facilities can pick it up there.
Proper documentation will take several K worth of text for many
sysctl variables, we don't want that in the kernel under any
circumstances.
I will welcome any well thought out attempt at improving the
situation wrt. sysctl documentation, but this wasn't it.
it's already on for the 2XX0) and detect the broken 1040A FIFO. Change
bzero to MEMZERO (portability with **nux). Use memcpy for same reason.
Finally detect QUEUE FULL conditions and return this as an error that
will get cam_periph_error to do it's 'tagged openings now XXX' dance.
than ".so". The old extension conflicted with well-established
naming conventions for dynamically loadable modules.
The "clean" targets continue to remove ".so" files too, to deal with
old systems.
was tested for month or two in production).
Noticed by: Stephen McKay
Stephen also suggested to remove the complication at all. I don't do it as
it would be backout of a large part of 1.190 (from 1998/03/16)...
on the ASIX AX88140A chip. Update /sys/conf/files, RELNOTES.TXT,
/sys/i388/i386/userconfig.c, sysinstall/devices.c, GENERIC and LINT
accordingly.
For now, the only board that I know of that uses this chip is the
Alfa Inc. GFC2204. (Its predecessor, the GFC2202, was a DEC tulip card.)
Thanks again to Ulf for obtaining the board for me. If anyone runs
across another, please feel free to update the man page and/or the
release notes. (The same applies for the other drivers.)
FreeBSD should now have support for all of the DEC tulip workalike
chipsets currently on the market (Macronix, Lite-On, Winbond, ASIX).
And unless I'm mistaken, it should also have support for all PCI fast
ethernet chipsets in general (except maybe the SMC FEAST chip, which
nobody seems to ever use, including SMC). Now if only we could convince
3Com, Intel or whoever to cough up some documentation for gigabit
ethernet hardware.
Also updated RELNOTEX.TXT to mention that the SVEC PN102TX is supported
by the Macronix driver (assuming you actually have an SVEC PN102TX with
a Macronix chip on it; I tried to order a PN102TX once and got a box
labeled 'Hawking Technology PN102TX' that had a VIA Rhine board inside
it).
devices dynamically. That means,
+ only one /dev/iic or /dev/smb device for each smb/iic bus to access
+ I2C/SMB device address must be given to any ioctl
+ new devices may be plugged and accessed after boot, which was
impossible previously (device addresses were hardcoded into
the kernel)
version and the asm version are inlined, and everything is cached,
the asm version is 1.75 times slower than the C version on P5's.
On K6's, it is only 1.25 times slower.
fixing it. See rev.1.22 of ../sound/audio.c for fixes. When both
the C version and the asm version are inlined, and everything is cached,
the asm version is 1.75 times slower than the C version on P5's. On
K6's, it is only 1.25 times slower.
versions of gcc and broken for current versions of egcs. The asm
here (for translate_bytes()) is now an interesting example of one
that needs to be volatile to work.
Fixed missing "memory" in the clobber list for translate_bytes().
Submitted by: "John S. Dyson" <dyson@iquest.net> but rewritten by me
versions of gcc and broken for current versions of egcs.
Cleaned up the asm statement for do_cpuid() a little.
Submitted by: "John S. Dyson" <dyson@iquest.net> but rewritten by me
RB_CONFIG.
Now, the code should do the right thing in the following cases, when
kernel is compiled with INTRO_USERCONFIG:
* when booted without userconfig_script and without RB_CONFIG, present
intro screen, and wait for user input.
* when booted with userconfig_script and without RB_CONFIG, DON'T present
intro screen unless explicitly asked in userconfig_script, basing on
assumption that if a user loads userconfig_script, (s)he already
decided what parameters to configure. Proceed with booting.
* when booted without userconfig_script, and with RB_CONFIG, enter
configuration utility and wait for user input.
* when booted with userconfig_script, and with RB_CONFIG, execute all
commands from userconfig_script, and DON'T leave the config utility,
but wait for user input.
And finally, regardless of the combination of the above parameters,
when intro screen is invoked either first or next times, and user
chooses to go back to CLI interface, unblock the quit command.
On a system with a large amount of ram (e.g. 2G), allocation of per-page
data structures (512K physical pages) could easily bust the initial kernel
page table (36M), and growth of kernel page table requires kptobj.
shared signal handling when there is shared signal handling being
used.
This removes the main objection to making the shared signal handling
a standard ability in rfork() and friends and 'unconditionalising'
this code. (i.e. the allocation of an extra 328 bytes per process).
Signal handling information remains in the U area until such a time as
it's reference count would be incremented to > 1. At that point a new
struct is malloc'd and maintained in KVM so that it can be shared between
the processes (threads) using it.
A function to check the reference count and move the struct back to the U
area when it drops back to 1 is also supplied. Signal information is
therefore now swapable for all processes that are not sharing that
information with other processes. THis should addres the concerns raised
by Garrett and others.
Submitted by: "Richard Seaman, Jr." <dick@tar.com>
to release the probe ccb before taking down the periph.
Also, don't do cdscheduling if you're not going to
attach the device after all.
Reviewed by: ken@freebsd.org
from sc, vt and sio drivers. Use instead a linker_set to collect them.
Staticize ??cngetc(), ??cnputc(), etc functions in sc and vt drivers.
We must still have siocngetc() and siocnputc() as globals because they
are directly referred to by i386-gdbstub.c :-(
Oked by: bde
already loaded and interpreted userconfig_script. Otherwise, when using
such kernel system would always block waiting for user input in UserConfig,
while the intention was to avoid this by having userconfig_script.
Reviewed by: msmith
that they might be about to blow their feet off if they have not been
reading their mail. I don't know if or how well this will work, but it's
worth a try.
It keeps returning queue full until we have reduced the number of tagged
openings to the minimum.
So, put in a quirk entry with the same work-around. This quirk entry is
only for the 9G Atlas III, once someone comes up with inquiry information
for the 18G version of that drive, we can quirk it as well.
Submitted by: "Johan Granlund" <johan@granlund.nu>
downward growing stacks more general.
Add (but don't activate) code to use the new stack facility
when running threads, (specifically the linux threads support).
This allows people to use both linux compiled linuxthreads, and also the
native FreeBSD linux-threads port.
The code is conditional on VM_STACK. Not using this will
produce the old heavily tested system.
Submitted by: Richard Seaman <dick@tar.com>
MNT_WAIT when we mean boolean `true' or check for that value not being
passed. There was no problem in practice because MNT_WAIT had the
magic value of 1.
and mx_setcfg() so that we can read the internal MII registers on the
MX98713 chip correctly. With these changes, media autoselection now
works correctly on the original 98713. All Macronix chips should now
be properly supported (unless there's a surprise waiting in the 98725).
Thanks to Ulf Zimmermann for providing a 98713 board.
list of devices which has been changed in UserConfig, without resorting
to reading /dev/kmem.
The data returned consist of series of struct isa_device and
char dev_name[8].
Ok'd by: jkh
the quirk that disables tagged queueing for those drives.
Also, silence a warning by disabling xpt_for_all_targets() and
xpt_for_all_periphs(). These two functions are not currently used, but
they should not be removed. They're part of a set of functions that
provide a way to execute a function for every {bus,target,device,periph} in
the system.
If anyone needs to use either function in the future, they can be
un-#ifdefed.
is enough to satisfy things like StarOffice. This is a hack, but doing
it properly would be a LOT of work, and would require extensive grovelling
around in the user address space to find the argv[].
Obtained from: Mostly from Andrzej Bialecki <abial@nask.pl>.
isolated to revision 33 PNIC chips is also present in revision 32 chips.
Cards with rev. 32 chips include the LinkSys LNE100TX and the Matrox
FastNIC 10/100. This accounts for all the cards that I have to test
with.
(I was never able to personally trip the bug on this chip rev, but today
one of the guys in the lab did it with the software they're working on
for their cellular IP project, which uses BPF and promiscuous mode
extensively.)
This commit enables the promiscuous mode software workaround code for
both revison 32 and revision 33 chips. It's possible all of the PNIC
chips suffer from this bug, but these are the only two revs where I
know for a fact it exists.
CAPACITY fail for a non-removable media device. There's a race
condition where the device entry is removed and then
xpt_release_ccb is called which attempts to give back the ccb
to a device that's now gone. In this bandaid release the ccb
early and then remember to not call xpt_release_ccb later.
- Special registers of IO-DATA device's RSA series are defined in
ic/rsa.h (new file).
Pointed out by: Bruce Evans <bde@zeta.org.au>
Submitted by: Takahashi Yoshihiro <nyan@wyvern.cc.kogakuin.ac.jp>
Noticed by: Carl Mascott <cmascott@world.std.com>
Don't write access time of a file more than once per day. (Its precision is
1 day anyway). Don't try to write access and creation time in nonwin95 case.
Suggested by: bde (long time ago).
used in device attach routines. At least for attaches at boot time,
actually waiting, or actually failing for malloc(..., M_NOWAIT), are
almost equally unlikely and harmless, but using M_WAITOK interferes
with automatic detection of bogus M_WAITOK's.
deltas, but it is possible since I had a few merge conflicts over the last
few days while this has been sitting ready to go.
(Part 1 was committed to the config files, but cvs aborted grrr..)
Approved by: core
I/O requests must be marked P_SYSTEM because if it isn't and the system
decides to swap it or (god forbid) kill it, the system stands a good
chance of locking up.
chip revisions. (A buggy taiwanese chip? I'm just shocked; shocked I tell
you.) So far I have only observed the anomalous behavior on board with
PCI revision 33 chips. At the moment, this seems to include only the
Netgear FA310-TX rev D1 boards with chips labeled NGMC169B. (Possibly this
means it's an 82c169B part from Lite-On.)
The bug only manifests itself in promiscuous mode, and usually only at
10Mbps half-duplex. (I have not observed the problem in full-duplex mode,
and I don't think it ever happens at 100Mbps.) The bug appears to be in
the receiver DMA engine. Normally, the chip is programmed with a linked
list of receiver descriptors, each with a receive buffer capable of holding
a complete full-sized ethernet frame. During periods of heavy traffic
(i.e. ping -c 100 -f 8100 <otherhost>), the receiver will sometimes appear
to upload its entire FIFO memory contents instead of just uploading the
desired received frame. The uploaded data will span several receive
buffers, in spite of the fact that the chip has been told to only use
one descriptor per frame, and appears to consist of previously transmitted
frames with the correct received frame appended to the end.
Unfortunately, there is no way to determine exactly how much data is
uploaded when this happens; the chip doesn't tell you anything except the
size of the desired received frame, and the amount of bogus data varies.
Sometimes, the desired frame is also split across multiple buffers.
The workaround is ugly and nasty. The driver assembles all of the data
from the bogus frames into a single buffer. The receive buffers are always
zeroed out, and we program the chip to always include the receive CRC
at the end of each frame. We therefore know that we can start from the
end of the buffer and scan back until we encounter a non-zero data byte,
and say conclusively that this is the end of the desired frame. We can
then subtract the frame length from this address to determine the real
start of the frame, and copy it into an mbuf and pass it on.
This is kludgy and time consuming, but it's better than dropping frames.
It's not too bad since the problem only happens at 10Mbps.
The workaround is only enabled for chips with PCI revision == 33. The
LinkSys LNE100TX and Matrox FastNIC 10/100 cards use a revision 32 chip
and work fine in promiscuous mode. Netgear support has confirmed that
they "have some previous knowledge of problems in promiscuous mode" but
didn't have a workaround. The people at Lite-On who would be able to
suggest a possible fix are on vacation. So, I decided to implement a
workaround of my own until I hear from them. I suppose this problem made
it through Netgear's QA department since Windows doesn't normally use
promiscuous mode, and if Windows doesn't need the feature than it can't
possibly be important, right? Grrr.
key? ( -- flag) \ check to see if there's a key to be read from input
ms ( u -- ) \ wait that many milliseconds
seconds ( -- u ) \ get number of seconds from midnight.
'words' now outputs the list page by page - this probably should go
through libstand's pager, but will have to wait for closer integration of
built-ins with Forth...
Submitted partially by: W Gerald Hicks <wghicks@bellsouth.net>
this has a problem with capture but i am not sure if it is related
to the mixer or what else.
But in the meantime, this is ok to listen to mpegs.
I also have a much simpler version of the driver in the works which
reuses a lot more of the existing "pcm" routines. Next year...
have all fields in network order, whereas ipfw expects some to be
in host order. This resulted in some incorrect matching, e.g. some
packets being identified as fragments, or bandwidth not being
correctly enforced.
NOTE: this only affects bridge+ipfw, normal ipfw usage was already
correct).
Reported-By: Dave Alden and others.
* Move the user stack from VM_MAXUSER_ADDRESS to a place below the 32bit
boundary (needed to support 32bit OSF programs). This should also save
one pagetable per process.
* Add cvtqlsv to the set of instructions handled by the floating point
software completion code.
* Disable all floating point exceptions by default.
* A minor change to execve to allow the OSF1 image activator to support
dynamic loading.
default for BINDIR. The default BINDIR of /usr/mdec can't be overridden
yet because libdisk still uses /usr/mdec and installing in /boot might
clobber the new boot blocks.
Don't install links to bootxx or xxboot.
Install boot1 and boot2 in 1 step.
Don't delete the boot.help source file on installing it when ${COPY} is
null.
"dying daemons" problem. (I thought this code was introduced in rev.1.80,
but it just relaxed the condition.)
Also, kill related "suggest more swap space" warning (also introduced in
1.80). It was confusing, to say the least...
Requested by: msmith
Not objected by: dg
There's something that's been bugging me for a while, so I decided to fix it.
FreeBSD now will DTRT WRT DDB and DDB_UNATTENDED (!debugger_on_panic), at least
in my opinion. The behavior change is such that:
1. Nothing changes when debugger_on_panic != 0.
2. When DDB_UNATTENDED (!debugger_on_panic), if a panic occurs, the
machine will reboot. Also, if a trap occurs, the machine will
panic and reboot, unlike how it broke to DDB before. HOWEVER,
a trap inside DDB will not cause a panic, allowing full use
of DDB without having to worry about the machine being stuck
at a DDB prompt if something goes wrong during the day.
Patches for this behavior follow my signature, and it would
be a boon to anyone (like me) who uses DDB_UNATTENDED, but
actually wants the machine to panic on a trap (otherwise,
what's the use, if the machine causes a fatal trap rather than
a true panic, of debugger_on_panic?). The changes cause no
adverse behavior, but do involve two symbols becoming global
Submitted by: Brian Feldman <green@unixhelp.org>
kernel as a pseudo-device. The changes were:
- #ifdef DEBUG -> #ifdef VINUMDEBUG
- opt_vinum.h for holding above config variable
- Fixing up a few stray problems where DEBUG wasn't optional.
- config.c -> vinumconfig.c (there's already a config.o)
- Other *.c -> vinum*.c (wasn't strictly necessary, but done in case we end
up with something else conflicting later on and we might have to have yet
more repository copies of files).
- include file paths fixups.. (ie: get them all from the kernel tree
instead of partly from the kernel and partly from /usr/include/machine)
I've spoken with Greg about this.. I hope this doesn't mess him around
too much..
CPU_WT_ALLOC does not work correctly for K6-2s of model 8+ and
probably K6-3s (when they appear on the market soon). In addition,
print_AMD_info() incorrectly printfs write allocation's size. I've
fixed them, so they now Do The Right Thing, and added a
"NO_MEMORY_HOLE" option to easily allow 15-16mb range handling for us
K6 and K6-2 users.
Submitted by: Brian Feldman <green@unixhelp.org>
ISDN4BSD is the work of our brand-new comitter: Hellmuth Michaelis,
who has done a tremendous amount of work to bring us this far.
There are still some outstanding issues and files to bring into
the tree, and for now it will be needed to pick up all the extra
docs from the isdn4bsd release.
It is probably also a very good idea to subscribe to the isdn@freebsd.org
mailing list before you try this out.
These files correspond to release "beta Version 0.70.00 / December
1998" from Hellmuth.
last cleanup. Since the oid_arg2 field of struct sysctl_oid is not wide
enough to hold a long, the SYSCTL_LONG() macro has been modified to only
support exporting long variables by pointer instead of by value.
Reviewed by: bde
Matt Jacob
Eivind Eklund
Kazutaka YOKOTA
Robert Nordier
Luigi Rizzo
Mike Smith
Nick Hibma
Bill Paul
Steve Price
Nicolas Souchu
Peter Wemm
Doug Rabson
Poul-Henning Kamp
Dag-Erling Smørgrav
Brian Somers
John Polstra
Dmitrij Tejblum
Bruce Evans
Kenjiro Cho
Andrzej Bialecki
KATO Takenori
Luoqi Chen
Julian Elischer
Kenneth D. Merry
Greg Lehey
Jordan K. Hubbard
Tim Vanderhoek
Matthew Dillon
Wolfram Schneider
Søren Schmidt
Gary Palmer