operands that are set during seqeuncer program download instead of at
assembly time.
Remove the REJBYTE sram variable. The host driver can just as easly
read the accumulator to get this value.
This should fix the reported problems with cards that don't have devices
attached to them failing with a stream of "Somone reset bus X" messages.
Doug Ledford determined the cause of the problem, fixes by me.
operands that are set during seqeuncer program download instead of at
assembly time.
Convert the sequencer code to use" downloaded constants" for four run time
constants that vary depending on the board type. This frees up 4 bytes
of sequencer scratch ram space where these constants used to be stored and
also removes the additional instructions required to load their values
into the accumulator prior to using them.
Remove the REJBYTE sram variable. The host driver can just as easly
read the accumulator to get this value.
The scratch ram savings is important as the old code used to clober the
SCSICONF register on 274X cards which sits near the top of scratch ram
space. The SCSICONF register controls bus termination, and clobbering
it is not a good thing. Now we have 4 bytes to spare.
This should fix the reported problems with cards that don't have devices
attached to them failing with a stream of "Somone reset bus X" messages.
Doug Ledford determined the cause of the problem, fixes by me.
1. Clustered I/O is switched by the MNT_NOCLUSTERR and MNT_NOCLUSTERW
bits of the mnt_flag. The sysctl variables, vfs.foo.doclusterread
and vfs.foo.doclusterwrite are deleted. Only mount option can
control clustered I/O from userland.
2. When foofs_mount mounts block device, foofs_mount checks D_CLUSTERR
and D_CLUSTERW bits of the d_flags member in the block device switch
table. If D_NOCLUSTERR / D_NOCLUSTERW are set, MNT_NOCLUSTERR /
MNT_NOCLUSTERW bits will be set. In this case, MNT_NOCLUSTERR and
MNT_NOCLUSTERW cannot be cleared from userland.
3. Vnode driver disables both clustered read and write.
4. Union filesystem disables clutered write.
Reviewed by: bde
- some addition of comments (for readability)
- iso-2022 G0 designation support. This does almost nothing. Just for
avoiding garbled screen when got "ESC ( B".
(how about G1/2/3 designation? I'm not sure)
(usually a couple of thousand) to 25. The measured impact on cache-hits
doesn't justify spending memory this way:
Target number of free vnodes versus namecache hit rate in % during a
make world:
10 98.5316
200 98.5479
500 98.5546
1000 98.5709
3000 98.6006
4000 98.6126
report slightly more than 64MB of total memory. This can happen due to the
total being the sum of both base and extended memory.
Submitted by: Alan Cox <alc@cs.rice.edu>
hash chain traversal isn't needed. This also allows untimeout to recompute
the hash to find the bucket that the entry to remove is stored in so
that each callout entry no longer needs to store that information.
Reviewed by: Nate Williams <nate@mt.sri.com>
buffer queue so I missed this when I changed buf_queue_head.
This probably fixes Soren's problem too, but he never mentioned
which CD driver he was using. 8-)
Submitted by: dave adkins <adkin003@tc.umn.edu>
Change the definition of a buffer queue so that bufqdisksort can
properly deal with bordered writes.
Add inline functions for accessing buffer queues. This should be
considered an opaque data structure by clients.
callout.h:
New callout implementation.
device.h:
Add support for CAM interrupts.
disk.h:
disklabel.h:
tqdisksort->bufqdisksort
kernel.h:
Add new configuration entries for configuration hooks and calling
cpu_rootconf and cpu_dumpconf.
param.h:
Add a priority for sleeping waiting on config hooks.
proc.h:
Update for new callout implementation.
queue.h:
Add TAILQ_HEAD_INITIALIZER from NetBSD.
systm.h:
Add prototypes for cpu_root/dumpconf, splcam, splsoftcam, etc..
Poul-Henning Kamp
KATO Takenori
Steve Passe
Justin T. Gibbs
Joerg Wunsch
Mike Smith
Jun-ichiro itojun Hagino
David Greenman
Garrett Wollman
John Polstra
Bruce Evans
Jordan K. Hubbard
Peter Wemm
John Dyson
Julian Elischer