2) Output K bytes instead of pages as this means something to more people.
3) Moved printf of avail memory to after vm_bounce_init() call so that
bounce buffers are included in the figure.
4) Killed initcpu(); it's an unused vestige from the VAX.
1) Make the driver "quiet" by sticking most boot messages behind
bootverbose conditionals. This means that you won't see the
sync and wide negotiation, but you will find out if they fail.
2) Add support to the 93cx6 serial eeprom code to read at an abitrary
offset. This is needed so that we can access the second half
of the eeprom on 3940 cards where the second channel's config
is stored.
3) Add flags argument to ahcprobe(). This is used by the pci probe code
to tell the generic driver that an adapter should be treated
as a channel B device as well as notify it of the presence of
external SCB SRAM. These are needed for some motherboard
implementations of the aic7870 and for the 3940 controllers.
4) Print "Channel A"/"Channel B" instead of "Single Channel" for the
two busses of the 3940. I received many reports of confusion
about how the 3940 was probed since most people belived that
only one ahc entry was needed. This will hopefully make it
clearer.
5) Walk the SCBs to determine just how many their are if external SCB
ram is detected.
6) Hard code that external SCB ram is present for the 3940 since it doesn't
use the documented reporting facility for reporting the SRAM. :(
255 commands per channel are supported on the 3940.
7) Read the seeprom starting at addres 32 for the second channel of the
3940 so we get the right info for that channel.
8) Clean up printing of the "Disabling tagged queuing message".
9) Queue timeouts if they occur while we are handling a timeout. The code
was totally unprotected in this scenario.
Reviewed by: Timeout code reviewed by David Greenman <davidg>
/*
+ * Code for MTERASE added by John Lind (john@starfire.mn.org) 95/09/02.
+ * This was very easy due to the excellent structure and clear coding
+ * of the original driver.
+ */
changes to allow devices that don't probe (e.g. /dev/mem)
to create devfs entries
this required giving 'configure' its own SYSINIT entry
so we could duck in just before it with a DEVFS init
and some device inits..
my devfs now looks like:
./misc
./misc/speaker
./misc/mem
./misc/kmem
./misc/null
./misc/zero
./misc/io
./misc/console
./misc/pcaudio
./misc/pcaudioctl
./disks
./disks/rfloppy
./disks/rfloppy/fd0.1440
./disks/rfloppy/fd1.1200
./disks/floppy
./disks/floppy/fd0.1440
./disks/floppy/fd1.1200
also some sligt cleanups.. DEVFS needs a lot of work
but I'm getting back to it..
had a 2.1 tag, thus sending these two changes into the 2.1 branch instead
of -current. Argh. I may bring these changes into the 2.1 anyway (they're
benign there) so I'm not going to admin them out of 2.1 for the time
being.
Submitted by: terry (terry lambert)
This is a composite of 3 patch sets submitted by terry.
they are:
New low-level init code that supports loadbal modules better
some cleanups in the namei code to help terry in 16-bit character support
some changes to the mount-root code to make it a little more
modular..
NOTE: mounting root off cdrom or NFS MIGHT be broken as I haven't been able
to test those cases..
certainly mounting root of disk still works just fine..
mfs should work but is untested. (tomorrows task)
The low level init stuff includes a total rewrite of init_main.c
to make it possible for new modules to have an init phase by simply
adding an entry to a TEXT_SET (or is it DATA_SET) list. thus a new module can
be added to the kernel without editing any other files other than the
'files' file.
calls with a byte size of 1. This special case was not
correctly emulated. Now programs such as a simple 'ls' to a commercial
Macintosh emulator called 'executor' will work correctly.
This is still very green, but I have managed to get my modem working.
Lots of work still to do, but now at least we can commit it. /phk
Reviewed by: phk
Submitted by: Andrew McRae <andrew@mega.com.au>
This change forces the controller drivers to allocate a scsibus_data struct
via a call to scsi_alloc_bus(), fill in the adapter_link field, and optionally
modify any other fields of the struct. Scsi_alloc_bus() initializes all fields
to the default, so the changes in most drivers are very minimal. For drivers
that support Wide controllers, the maxtarg field will have to be updated to
allow probing of all targets (for an example, look at the aic7xxx driver).
Scsi_attachdevs() now takes a scsibus_data* as its argument instead of an
sc_link*. This allows us to expand the role of the scsibus_data struct for
other bus level configuration setings (max number of transactions, current
transaction opennings, etc for better tagged queuing support).
Reviewed by: Rodney Grimes <rgrimes>, Peter Dufault <dufault>, Julian Elischer <julian>
Change some leading spaces to tabs.
This change forces the controller drivers to allocate a scsibus_data struct
via a call to scsi_alloc_bus(), fill in the adapter_link field, and optionally
modify any other fields of the struct. Scsi_alloc_bus() initializes all fields
to the default, so the changes in most drivers are very minimal. For drivers
that support Wide controllers, the maxtarg field will have to be updated to
allow probing of all targets (for an example, look at the aic7xxx driver).
Scsi_attachdevs() now takes a scsibus_data* as its argument instead of an
sc_link*. This allows us to expand the role of the scsibus_data struct for
other bus level configuration setings (max number of transactions, current
transaction opennings, etc for better tagged queuing support).
Reviewed by: Rodney Grimes <rgrimes>, Peter Dufault <dufault>, Julian Elischer <julian>
Julian Elischer
Bruce Evans
David Greenman
Jordan K. Hubbard
Steven Wallace
Bill Paul
John Dyson
Justin T. Gibbs
Guido van Rooij
Joerg Wunsch
Poul-Henning Kamp