make it more intelligible, improve the partially bogus locking, and
allow for a ``quick re-acquiration'' from a pending release of timer 0
that happened ``recently'', so it was not processed yet by clkintr().
This latter modification now finally allows to play XBoing over
pcaudio without losing sounds or getting complaints. ;-) (XBoing
opens/writes/closes the sound device all over the day.)
Correct locking for sysbeep().
Extensively (:-) reviewed by: bde
Testing with the high frequency of 20000 Hz (to find problems) only found
the problem that this frequency is too high for slow i386's.
Disable interrupts while setting the timer frequency. This was unnecessary
before rev.1.57 and forgotten in rev.1.57. The critical (i8254) interrupts
are disabled in another way at boot time but not in the sysctl to change
the frequency.
enable flag instead of enable_intr() to restore it to its usual state.
getit() is only called from DELAY() so there is no point in optimising
its speed (this wasn't so clear when it was extern), and using
enable_intr() made it inconvenient to call DELAY() from probes that need
to run with interrupts disabled.
All new code is "#ifdef PC98"ed so this should make no difference to
PC/AT (and its clones) users.
Ok'd by: core
Submitted by: FreeBSD(98) development team
ansi and traditional cpp.
The nesting rules of macros are different, which required some changes.
Use __CONCAT(x,y) instead of /**/.
Redo some comments to use /* */ rather than "# comment" because the ansi
cpp cares about those, and also cares about quote matching.
time. The results are currently ignored unless certain temporary options
are used.
Added sysctls to support reading and writing the clock frequency variables
(not the frequencies themselves). Writing is supposed to atomically
adjust all related variables.
machdep.c:
Fixed spelling of a function name in a comment so that I can log this
message which should have been with the previous commit.
Initialize `cpu_class' earlier so that it can be used in startrtclock()
instead of in calibrate_cyclecounter() (which no longer exists).
Removed range checking of `cpu'. It is always initialized to CPU_XXX
so it is less likely to be out of bounds than most variables.
clock.h:
Removed I586_CYCLECTR(). Use rdtsc() instead.
clock.c:
TIMER_FREQ is now a variable timer_freq that defaults to the old value of
TIMER_FREQ. #define'ing TIMER_FREQ should still work and may be the best
way of setting the frequency.
Calibration involves counting cycles while watching the RTC for one second.
This gives values correct to within (a few ppm) + (the innaccuracy of the
RTC) on my systems.
regarding apm to LINT
- Disabled the statistics clock on machines which have an APM BIOS and
have the options "APM_BROKEN_STATCLOCK" enabled (which is default
in GENERIC now)
- move around some of the code in clock.c dealing with the rtc to make
it more obvios the effects of disabling the statistics clock
Reviewed by: bde
channel at the same time. The functions isa_dma_acquire() and
isa_dma_release() should be used in all ISA drivers which call isa_dmastart().
This can be used more generally to register the usage of DMA channels in
any driver, but it is required for drivers using isa_dmastart() and friends.
Clean up sanity checks, error messages, etc.
Remove isa_dmadone_nobounce(), it is no longer needed
Reviewed by: bde
Always delay using one inb(0x84) after each i/o in rtcin() - don't
do this conditional on the bogus option DUMMY_NOPS not being defined.
If you want an optionally slightly faster rtcin() again, then inline
it and use a better named option or sysctl variable. It only needs
to be fast in rtcintr().
clock interrupts.
Keep a 1-in-16 smoothed average of the length of each tick. If the
CPU speed is correctly diagnosed, this should give experienced users
enough information to figure out a more suitable value for `tick'.
fd and wt drivers need bounce buffers, so this normally saves 32K-1K
of kernel memory.
Keep track of which DMA channels are busy. isa_dmadone() must now be
called when DMA has finished or been aborted.
Panic for unallocated and too-small (required) bounce buffers.
fd.c:
There will be new warnings about isa_dmadone() not being called after
DMA has been aborted.
sound/dmabuf.c:
isa_dmadone() needs more parameters than are available, so temporarily
use a new interface isa_dmadone_nobounce() to avoid having to worry
about panics for fake parameters. Untested.
variants, idea taken from NetBSD clock.c.
At least year calculation was wrong, pointed by Bruce.
Use different strategy to store year for BIOS without RTC_CENTURY
was overlapping with another file, and making some undesirable behavior a
little worse - it's triggering a bug in config that appears to have been
there for some time (before the options files, anyway.)
feature of the ICU. auto-EOI on the slave is not safe, however, so it
remains an option. Killed religious FASTER_NOP when writing the ICU.
Reviewed by: bde
overflows.
It sure would be nice if there was an unmapped page between the PCB and
the stack (and that the size of the stack was configurable!). With the
way things are now, the PCB will get clobbered before the double fault
handler gets control, making somewhat of a mess of things. Despite this,
it is still fairly easy to poke around in the overflowed stack to figure
out the cause.
- Don't print out meaningless iCOMP numbers, those are for droids.
- Use a shorter wait to determine clock rate to avoid deficiencies
in DELAY().
- Use a fixed-point representation with 8 bits of fraction to store
the rate and rationalize the variable name. It would be
possible to use even more fraction if it turns out to be
worthwhile (I rather doubt it).
The question of source code arrangement remains unaddressed.
bit set. I broke stat_imask in Dec 1994 and update_intr_masks() has
copied the breakage to intr_mask[8] since Mar 1995. This can cause
the RTC to stop interrupting in rare cases (under loads heavy enough
for a new RTC interrupt to occur at a critical time just before Xintr8
finishes handling the previous one) and may have caused worse problems.
Convert the remaining sysctl stuff to the new way of doing things.
the devconf stuff is the reason for the large number of files.
Cleaned up some compiler warnings while I were there.
Joerg Wunsch
Bruce Evans
Satoshi Asami
Paul Traina
Peter Wemm
Poul-Henning Kamp
Nate Williams
Justin T. Gibbs
Sujal Patel
Andrey A. Chernov
Jordan K. Hubbard
Mike Pritchard
Garrett Wollman
Mark Murray
David Greenman