for possible buffer overflow problems. Replaced most sprintf()'s
with snprintf(); for others cases, added terminating NUL bytes where
appropriate, replaced constants like "16" with sizeof(), etc.
These changes include several bug fixes, but most changes are for
maintainability's sake. Any instance where it wasn't "immediately
obvious" that a buffer overflow could not occur was made safer.
Reviewed by: Bruce Evans <bde@zeta.org.au>
Reviewed by: Matthew Dillon <dillon@apollo.backplane.com>
Reviewed by: Mike Spengler <mks@networkcs.com>
not like the 6-byte read and write commands! It returns illegal request,
with the field pointer pointing to byte 9 of a 6 byte CDB.
In any case, the work around is to put in a quirk mechanism that makes sure
that we don't send 6-byte reads or writes to this device. It's rather sad
that this is necessary. You'd think that they would be able to get
something that basic to work right in their firmware...
Reviewed by: gibbs
Reported by: Adam McDougall <bsdx@spawnet.com>
to a device failed.
In theory, the same steps that happen when we get an AC_LOST_DEVICE async
notification should have been taken when a driver fails to attach. In
practice, that wasn't the case.
This only affected the da, cd and ch drivers, but the fix affects all
peripheral drivers.
There were several possible problems:
- In the da driver, we didn't remove the peripheral's softc from the da
driver's linked list of softcs. Once the peripheral and softc got
removed, we'd get a kernel panic the next time the timeout routine
called dasendorderedtag().
- In the da, cd and possibly ch drivers, we didn't remove the
peripheral's devstat structure from the devstat queue. Once the
peripheral and softc were removed, this could cause a panic if anyone
tried to access device statistics. (one component of the linked list
wouldn't exist anymore)
- In the cd driver, we didn't take the peripheral off the changer run
queue if it was scheduled to run. In practice, it's highly unlikely,
and maybe impossible that the peripheral would have been on the
changer run queue at that stage of the probe process.
The fix is:
- Add a new peripheral callback function (the "oninvalidate" function)
that is called the first time cam_periph_invalidate() is called for a
peripheral.
- Create new foooninvalidate() routines for each peripheral driver. This
routine is always called at splsoftcam(), and contains all the stuff
that used to be in the AC_LOST_DEVICE case of the async callback
handler.
- Move the devstat cleanup call to the destructor/cleanup routines, since
some of the drivers do I/O in their close routines.
- Make sure that when we're flushing the buffer queue, we traverse it at
splbio().
- Add a check for the invalid flag in the pt driver's open routine.
Reviewed by: gibbs
1) The vnode pager wasn't properly tracking the file size due to
"size" being page rounded in some cases and not in others.
This sometimes resulted in corrupted files. First noticed by
Terry Lambert.
Fixed by changing the "size" pager_alloc parameter to be a 64bit
byte value (as opposed to a 32bit page index) and changing the
pagers and their callers to deal with this properly.
2) Fixed a bogus type cast in round_page() and trunc_page() that
caused some 64bit offsets and sizes to be scrambled. Removing
the cast required adding casts at a few dozen callers.
There may be problems with other bogus casts in close-by
macros. A quick check seemed to indicate that those were okay,
however.
2217's (reported by Matthew Jacob in NetBSD PR kern/6027) and Fujitsu
M2954's (reported by Tom Jackson).
Some of the Fujitsus at least hang when they get a cache sync command.
(Others just return illegal request.)
Also, make error printing in dashutdown() a little more selective. Don't
print any error when the sense key is illegal request. Drives that don't
support the synchronize cache command usually return illegal request.
Also, make sure the scsi status is check condition before going into
scsi_sense_print().
Reviewed by: gibbs
command on drives that don't like it. Right now, there's just a bogus
quirk entry in the table that doesn't do anything, but that should be
changed once we get actual inquiry data for drives that don't like the
synchronize cache command.
Also, add a shutdown hook that runs through all direct access peripherals
and runs a synchronize cache on them if they're still open, and if
synchronize cache isn't disabled via a quirk entry.
Add a synchronize cache call at the end of dadump() (again, conditionalized
on the quirk entry), so we can insure that the disk cache contents get
flushed to physical media after a dump.
Check the new quirk entry in daclose() to decide whether or not to
synchronize the cache for a disk at final close.
Reviewed by: gibbs
JAZ drive happy. This shouldn't impact fast drives, and will keep cam
from failing on very slow ones (that are spinning up, say). 20
seconds was almost long enough, but not in all cases.
Suggested by: gibbs
well) Among them:
[ cd driver ]
1. Old labeling code was still there.
2. Error handling for dsopen() was broken (no test for the `error'
returned by dsopen(); bogus test of an `error' that is known to be 0).
3. cdopen() closed the physical device after certain errors although there
may still be open partitions on it.
4. cdclose() closed the physical device although there may still be open
partitions on it.
5. Some printf format fixes was incomplete or missing.
6. cdioctl() truncated unit numbers mod 256.
7. cdioctl() was missing locking.
[ da driver ]
1. daclose() closed the physical device although there may still be open
partitions on it. This was fixed many years ago in sd.c rev.1.57.
2. A minor optimization (the dk_slices != NULL test) in sdopen() became
uglier in daopen(). It is not worth doing. da only regressed compared
with od and my version of sd, since I never committed the change to sd.
daopen() should probably do less if some partition is already open.
This is not addressed by the diffs.
[ ... ]
5. "opt_hw_wdog.h" was not included, so the HW_WDOG code was unreachable.
- Added a getdev CCB call in the cdopen() and daopen() calls so that the
vendor name and device name are available for the disklabel. (suggested
by bde)
- Removed vestigal devfs support in both drivers, since we can't properly
work with devfs yet. (ask bde for details on this)
- Cleaned up the probe code in both drivers in the failure cases. There
were a number of things wrong here. The peripheral driver instances
weren't getting properly cleaned up. Sometimes the wrong probe message
would get printed out (with the failure message appended), so it wasn't
very clear that we failed to attach. SCSI sense information was printed,
even when the error in question wasn't a SCSI error. I put similar fixes
into the changer driver in revision 1.2 of scsi_ch.c.
Reviewed by: gibbs
Submitted by: bde (partially)
a perfect world, we'd notice the UA and do some device validation to ensure
that the device hasn't changed. We may get this before the year ends,
but not before 3.0R. This change gives the adminstrator ample ammunition
to take off a foot or two, but hey this *is* UN*X.
without the DA driver.
The problem was that the CD driver depended on scsi_read_write() and
scsi_start_stop(), which were defined in scsi_da.c.
I moved both functions, and their associated data structures and defines
from scsi_da.* to scsi_all.*. This is technically the "wrong" thing to do
since those commands are really only for direct-access type devices, not
for all SCSI devices. I think, though, that the advantage (allowing people
to compile kernels without the disk driver) outweighs any architectural
purity arguments.
PR: kern/7969
Reviewed by: gibbs
Archie Cobbs
Kenneth D. Merry
David Greenman
Warner Losh
Justin T. Gibbs