- probe for PHYs by checking the BMSR (phy status) register instead
of the vendor ID register.
- fix the autonegotiation routine so that it figures out the autonegotiated
modes correctly.
- add tweaks to support the Olicom OC-2326 now that I've actually had
a chance to test one
o Olicom appears to encode the ethernet address in the EEPROM
in 16-bit chunks in network byte order. If we detect an
Olicom card (based on the PCI vendor ID), byte-swap the station
address accordingly.
XXX The Linux driver does not do this. I find this odd since
the README from the Linux driver indicates that patches to
support the Olicom cards came from somebody at Olicom; you'd
think if anyone would get that right, it'd be them. Regardless,
I accepted the word of the disgnoatic program that came bundled
with the card as gospel and fixed the attach routine to make
the station address match what it says.
o The version of the 2326 card that I got for testing is a
strange beast: the card does not look like the picture on
the box in which it was packed. For one thing, the picture
shows what looks like an external NS 83840A PHY, but the
actual card doesn't have one. The card has a TNETE100APCM
chip, which appears to have not only the usual internal
tlan 10Mbps PHY at MII address 32, but also a 10/100 PHY
at MII address 0. Curiously, this PHY's vendor and device ID
registers always return 0x0000. I suspect that this is
a mutant version of the ThunderLAN chip with 100Mbps support.
This combination behaves a little strangely and required the
following changes:
- The internal PHY has to be enabled in tl_softreset().
- The internal PHY doesn't seem to come to life after
detecting the 100Mbps PHY unless it's reset twice.
- If you want to use 100Mbps modes, you have to isolate
the internal PHY.
- If you want to use 10Mbps modes, you have to un-isolate
the internal PHY.
The latter two changes are handled at the end of tl_init(): if
the PHY vendor ID is 0x0000 (which should not be possible if we
have a real external PHY), then tl_init() forces the internal
PHY's BMCR register to the proper values.
Change the port address argument to pci_map_port to pci_port_t* which is
defined as u_int on the alpha, u_short on i386. This is a stopgap with a
hopefully limited lifetime.
Discussed with: Stefan Esser <se@freebsd.org>
respectively. Most of the longs should probably have been
u_longs, but this changes is just to prevent warnings about
casts between pointers and integers of different sizes, not
to fix poorly chosen types.
cure the problems I was having with interrupts not being acknowledged
on time. This fixes a problem I observed where starting two ping -f
processes at 10Mbps would cause an adapter check due to TX GO commands
being issued before TXEOC interrupts were being acked.
Also fix a small problem with tl_start(): the mechanism I was using
to queue new packets onto the TX chain was bogus.
Change adapter check handler so that it resets card state after
tl_softreset() is stored.
Moved all EEPROM-related macro definitions into if_tlreg.h.
Don't allow an autoneg session to start until after the TX queue has
been drained, and don't transmit anything until after the autoneg
session is complete.
Also add support for two more Compaq ThunderLAN-based cards, and three
cards from Olicom which also use the ThunderLAN chip. The only thing
different about the Olicom cards is that they store the station address
at a different location within the EEPROM.
hidden). Now "ticks" are used, which are 4 byte, not 8 byte in size.
The size mismatch did not matter due to sufficient padding at the end
of the structure that holds time stamps (there is an unused member).
The fix suggested by Bruce Evans used "sizeof (ticks_t)", but I prefer
to use "sizeof ticks", and didn't seem to object in his last mail on
this topic.
Submitted by: bde
`#if defined(ONE_THING)' is a style bug, and i386 instead of __i386__
is a bug, since i386 is never defined when the kernel is compiled
by with the default flags (`gcc -ansi ...'). Here the bug disabled
the call to pmap_setvidram(), so ISA video memory was not mapped
WC on 686's. The bug may have been masked by bugs in the committer's
version of gcc - `gcc -ansi' incorrectly defines i386 for gcc = the
version of egcs on the 2.2.6 cdrom.
and don't depend on them being declared there. This will cause lots of
warnings for a few minutes until config is updated. Interrupt handlers
should never have been configured by config, and the machine generated
declarations get in the way of changing the arg type from int to void *.
- connector selection values (should fix aui/bnc),
- non-shifting version of crc calculation using a table,
- interrupt mask adjustments,
- add some brackets where a #ifdef could break an if(),
- don't reset the card unless it's up.
work in progress and has never booted a real machine. Initial
development and testing was done using SimOS (see
http://simos.stanford.edu for details). On the SimOS simulator, this
port successfully reaches single-user mode and has been tested with
loads as high as one copy of /bin/ls :-).
Obtained from: partly from NetBSD/alpha
or unsigned int (this doesn't change the struct layout, size or
alignment in any of the files changed in this commit, at least for
gcc on i386's. Using bitfields of type u_char may affect size and
alignment but not packing)).
FreeBSD/alpha. The most significant item is to change the command
argument to ioctl functions from int to u_long. This change brings us
inline with various other BSD versions. Driver writers may like to
use (__FreeBSD_version == 300003) to detect this change.
The prototype FreeBSD/alpha machdep will follow in a couple of days
time.
I had a reason for doing this, but it violates the principle of least
astonishment. (At some point I may put this back but attach it to one of
the LINK flags so the behavior can be toggled on and off.)
Also replace my tl_calchash() with a much less disgusting and substantially
smaller one supplied by Bill Fenner.
These are probably generated by other PCI devices sharing the TLAN's
interrupt. The programmer's guide says to simply re-enable interrupts
and return if one of these is detected.
Prompted by bug report from: Bill Fenner
in -current is over, I'll put a 2.2.x specific version in the RELENG_2_2
branch. If somebody wants a 2.2 version of this driver now, they can check
out the previous version from CVS or ask me via e-mail.
Gee people, I didn't mean to stir up such a controversy. I just wanted
to make sure I could get this thing to work with both kernel versions
and didn't want to have to maintain two separate copies. All ya hadda
do was ask. :)
drivers here do and it also blows up in building GENERIC during
a release build if you try and include <osreldate.h> (which shot
my SNAP dead - argh!). Use __FreeBSD__ instead.
This driver supports the following cards/integrated ethernet controllers:
Compaq Netelligent 10, Compaq Netelligent 10/100, Compaq Netelligent 10/100,
Compaq Netelligent 10/100 Proliant, Compaq Netelligent 10/100 Dual Port,
Compaq NetFlex-3/P Integrated, Compaq NetFlex-3/P Integrated,
Compaq NetFlex 3/P w/ BNC, Compaq Deskpro 4000 5233MMX.
It should also support Texas Instruments NICs that use the ThunderLAN
chip, though I don't have any to test. If you've got a card that uses
the ThunderLAN chip but isn't listed in the PCI vendor/product list in
if_tl.c, try adding it and see what happens.
The driver supports any MII compliant PHY at 10 or 100Mbps speeds in
full or half duplex. (Those I've personally tested are the National
Semiconductor DP83840A (Prosignia server), the Level 1 LXT970 (Deskpro
desktop), and the ThunderLAN's internal 10baseT PHY.) Autonegotiation,
hardware multicast filtering, BPF and ifmedia support are included.
This chip is pretty fast; Prosignia servers with NCR SCSI, ThunderLAN
ethernet and FreeBSD make for a nice combination.
Submitted by: Roger Hardiman <roger@cs.strath.ac.uk>
options BROOKTREE_SYSTEM_DEFAULT=BROOKTREE_PAL
in the kernel config file makes the driver's video_open() function
select PAL rather than NTSC. This fixed all the hangs on my
Dual Crystal card when using a PAL video signal.
As a result, you can loose the tsleep (of 2 seconds - now 0.25!!)
which I previously added. (Unless someone else wanted the 0.25
second tsleep).
submitted ioctl to clear the video buffer
prior to starting video capture
Amancio : clean up yuv12 so that it does not
affect rgb capture. Basically, fxtv after
capturing in yuv12 mode , switching to rgb
would cause the video capture to be too bright.
1.32 disable inverse gamma function for rgb and yuv
capture. fixed meteor brightness ioctl it now
converts the brightness value from unsigned to
signed.
1.33 added sysctl: hw.bt848.tuner, hw.bt848.reverse_mute,
hw.bt848.card
card takes a value from 0 to bt848_max_card
tuner takes a value from 0 to bt848_max_tuner
reverse_mute : 0 no effect, 1 reverse tuner
mute function some tuners are wired reversed :(
as variables declared in the main block in the function, so shadowing
of parameters by variables declared in the main block is not just an
obfuscation).
Found by: lint
Bill Paul
David Greenman
Doug Rabson
Mike Smith
Justin T. Gibbs
Bruce Evans
Søren Schmidt
Amancio Hasty
Stefan Eßer
Peter Wemm
Semen Ustimenko
John-Mark Gurney
Joseph Koshy
John Dyson
Eivind Eklund
Poul-Henning Kamp
Jordan K. Hubbard
KATO Takenori