- Refined internal interface in keyboard drivers so that:
1. the side effect of device probe is kept minimal,
2. polling mode function is added,
3. and new ioctl and configuration options are added (see below).
- Added new ioctl: KDSETREPEAT
Set keyboard typematic rate. There has existed an ioctl command,
KDSETRAD, for the same purpose. However, KDSETRAD is dependent on
the AT keyboard. KDSETREPEAT provides more generic interface.
KDSETRAD will still be supported in the atkbd driver.
- Added new configuration options:
ATKBD_DFLT_KEYMAP
Specify a keymap to be used as the default, built-in keymap.
(There has been undocumented options, DKKEYMAP, UKKEYMAP, GRKEYMAP,
SWKEYMAP, RUKEYMAP, ESKEYMAP, and ISKEYMAP to set the default keymap.
These options are now gone for good. The new option is more general.)
KBD_DISABLE_KEYMAP_LOADING
Don't allow the user to change the keymap.
the screen width.
- Store the current video mode information in the `video_adapter' struct.
- The size of the `v_offscreensize' field in the VESA mode information
block is u_int16, not u_int8.
- Bring down the splash screen when a vty is opened for the first
time.
- Make sure the splash screen/screen saver is stopped before
switching vtys.
- Read and save initial values in the BIOS data area early.
VESA BIOS may change BIOS data values when switching modes.
- Fix missing '&' operator.
- Move ISA specific part of driver initialization to syscons_isa.c.
atkbd
- kbdtables.h is now in /sys/dev/kbd.
all
- Adjust for forthcoming alpha port. Submitted by: dfr
0 success
EAGAIN try again later
other don't call this screen saver again
- Test flags consistently to examine the status of the screen saver.
scrn_blanked: the screen saver is running
scp->status & SAVER_RUNNING: the saver is running in this vty
- Correctlyu preserve status flag bits in set/restore_scrn_saver_mdoe().
keyboard and video card drivers.
Because of the changes, you are required to update your kernel
configuration file now!
The files in sys/dev/syscons are still i386-specific (but less so than
before), and won't compile for alpha and PC98 yet.
syscons still directly accesses the video card registers here and
there; this will be rectified in the later stages.
from sc, vt and sio drivers. Use instead a linker_set to collect them.
Staticize ??cngetc(), ??cnputc(), etc functions in sc and vt drivers.
We must still have siocngetc() and siocnputc() as globals because they
are directly referred to by i386-gdbstub.c :-(
Oked by: bde
truncated to 32 bits.
* Change the calling convention of the device mmap entry point to
pass a vm_offset_t instead of an int for the offset allowing
devices with a larger memory map than (1<<32) to be supported
on the alpha (/dev/mem is one such).
These changes are required to allow the X server to mmap the various
I/O regions used for device port and memory access on the alpha.
- Express various sizes in bytes, rather than Kbytes, in the video
mode and adapter information structures.
- Fill 0 in the linear buffer size field if the linear frame buffer
is not available.
- Remove SW_VESA_USER ioctl. It is still experimetal and was not meant
to be released.
- Fix missing cast operator.
- Correctly handle pointers returned by the VESA BIOS. The pointers
may point to the area either in the BIOS ROM or in the buffer supplied
by the caller.
- Set the destructive cursor at the right moment.
- there were too many global variables (there still are :-).
- the data section was bloated by explicit initializations of static
variables to 0 (only fixed the recently changed ones).
- WRAPHIST() had silly parentheses around foo->bar.
- the comment about inline functions was stale.
- the comment about Userconfig presumes too much about the boot environment.
- `i' was reused confusingly in scioctl().
- the declaration of `butmap' used a deprecated K&R misfeature.
- the initializeation of `butmap' had an unnecessary line break.
- `unsigned char' was not consistently (mis)spelled as u_char.
- English was poor in a comment in videoio.c.
Submitted by: bde
- Handle pixel (raster text) mode properly.
- Clear screen and paint border right.
- Paint text attribute (colors).
- Fix off-by-one errors.
- Add some sanity checks.
- Fix some function prototypes.
- Add some comment lines.
- Define generic text mode numbers so that the user can just give
"80x25", "80x60", "132x25"..., rather than "VGA_xxx", to `vidcontrol'
to change the current video mode. `vidoio.c' and `vesa.c' will map
these numbers to real video mode numbers appropriate and available
with the given video hardware. I believe this will be useful to make
syscons more portable across archtectures.
Kazu writes:
The VESA support code requires vm86 support. Make sure your kernel
configuration file has the following line.
options "VM86"
If you want to statically link the VESA support code to the kernel,
add the following option to the kernel configuration file.
options "VESA"
The vidcontrol command now accepts the following video mode names:
VESA_132x25, VESA_132x43, VESA_132x50, VESA_132x60, VESA_800x600
The VESA_800x600 mode is a raster display mode. The 80x25 text will
be displayed on the 800x600 screen. Useful for some laptop computers.
vidcontrol accepts the new `-i <info>' option, where <info> must be
either `adapter' or `mode'. When the `-i adapter' option is given,
vidcontrol will print basic information (not much) on the video
adapter. When the `-i mode' option is specified, vidcontrol will
list video modes which are actually supported by the video adapter.
Submitted by: Kazutaka YOKOTA yokota@FreeBSD.ORG
for the Lite2 fix for always returning EIO in dead_read().
Cleaned up the cdevswitch initializers for all tty drivers.
Removed explicit calls to ttsetwater() from all (tty) drivers. ttsetwater()
is now called centrally for opens, not just for parameter changes.
chip.
It has been observed that the problem is most apparent:
a) in notebook computers,
b) and/or in the systems with C&T video chips.
Define the new configuration option SC_BAD_FLICKER in the kernel
configuration file to remove outb()/outw() calls in question.
saver and splash screen can all work properly with syscons. Note that
the splash screen option (SC_SPLASH_SCREEN) does not work yet, as it
requires additional code from msmith.
- Reorganized the splash screen code to match the latest development
in this area.
- Delay screen switch in `switch_scr()' until the screen saver is
stopped, if one is running,
- Start the screen saver immediately, if any, when the `saver' key is
pressed. (There will be another commit for `kbdcontrol' to support
this keyword in the keymap file.)
- Do not always stop the screen saver when mouse-related ioctls
are called. Stop it only if the mouse is moved or buttons are
clicked; don't stop it if any other mouse ioctls are called.
2. Added provision to write userland screen savers. (Contact me if you
are interested in writing one.)
- Added CONS_IDLE, CONS_SAVERMODE, and CONS_SAVERSTART ioctls to
support userland screen savers.
3. Some code clean-ups.
the screen mode is changed even if another vty has larger size.
Reallocate the buffer only when the new screen size is larger than
the current cut buffer size.
When bell is of "quiet" types, the console won't ring (or flush)
if the ringing process is in a background vty.
PR: i386/2853
- Modify the escape sequence 'ESC[=%d;%dB' so that bell pitch and
duration are set in hertz and msecs by kbdcontrol(1).
There will be a corresponding kbdcontrol patch.
PR: bin/6037
Submitted by: Kouichi Hirabayashi (kh@eve.mogami-wire.co.jp)
is the kernel part of my commits, the userlevel stuff will be done in
a separate commit. Add the ability to suspend as well as hibernate to
syscons. Create a new virtual key like hibernate for suspend. Update
apm_bios.h to define more apm bios goodies.
Kazutaka YOKOTA
Dag-Erling Smørgrav
Poul-Henning Kamp
Matthew Dillon
Archie Cobbs
Doug Rabson
Peter Wemm
Bruce Evans
Andrey A. Chernov
Søren Schmidt
Warner Losh