with an error condition such as EINTR, EWOULDBLOCK, and ERESTART,
are reported to the application, not silently conceal. This
behavior was copied from the {read,write}v() syscalls, and is
appropriate there but not here.
o Correct a bug in extattr_delete() wherein the LOCKLEAF flag is
passed to the wrong argument in namei(), resulting in some
unexpected errors during name resolution, and passing in an unlocked
vnode.
Obtained from: TrustedBSD Project
gif/faith/stf moved to 0xfN entries, since their previous location
is allocated to some other interfaces.
Also add the IFT_PVC, which is the ATM PVC subinterface from ALTQ.
This also syncs us up a bit to NetBSD again.
This change requires a total recompilation of all kmem users, as
itojun told me.
Next in line is synching to the IANI SMI list.
Approved by: itojun
Disable "cache line streaming" for aic7890/91 Rev A chips. I
have never seen these chips fail using this feature, but
some of Adaptec's regression tests have.
Explicitly set "cache line streaming" to on for aic7896/97
chips. This was happening before, but this documents the
fact that these chips will not function correctly without
CACHETHEEN set.
aic7xxx.h:
Add new bug types.
Fix a typo in a comment.
aic7xxx.reg:
Add a definition for the SHVALID bit in SSTAT3 for Ultra2/3
chips. This bit inicates whether the bottom most (current)
element in the S/G fifo has exhausted its data count.
aic7xxx.seq:
Be more careful in how we turn off the secondary DMA channel.
Being less careful may hang the PCI bus arbitor that negotiates
between the two DMA engines.
Remove an unecessary and incorrect flag set operation in
the overrun case.
On Ultra2/3 controllers, clear the dma FIFO before starting
to handle an overrun. We don't want any residual bytes from
the beginning of the overrun to cause the code that shuts
down the DMA engine from hanging because the FIFO is not
(and never will be) empty.
If the data fifo is empty by the time we notice that a
read transaction has completed, there is no need to
hit the flush bit on aic7890/91 hardware that will not
perform an auto-flush. Skip some cycles by short circuiting
the manual flush code in this case.
When transitioning out of data phase, make sure that we
have the next S/G element loaded for the following
reconnect if there is more work to do. The code
would do this in most cases before, but there was
a small window where the current S/G element could
be exhausted before our fetch of the next S/G element
completed. Since the S/G fetch is already initiated
at this point, it makes sense to just wait for the
segment to arrive instead of incuring even more latency
by canceling the fetch and initiating it later.
Fast path the end of data phase handling for the last
S/G segment. In the general case, we might have
worked ahead a bit by stuffing the S/G FIFO with
additional segments. If we stop before using them
all, we need to fixup our location in the S/G stream.
Since we can't work past the last S/G segment, no
fixups are ever required if we stop somewhere in
that final segment.
Fix a little buglet in the target mode dma bug handler.
We were employing the workaround in all cases instead
of only for the chips that require it.
Fix the cause of SCB timeouts and possible "lost data"
during read operations on the aic7890. When sending
a data on any Ultra2/3 controller, the final segment
must be marked as such so the FIFO will be flushed and
cleaned up correctly when the transfer is ended. We
failed to do this for the CDB transfer and so, if
the target immediately transfered from command to data
phase without an intervening disconnection, the first
segment transferred would be any residual bytes from
the cdb transfer. The Ultra160 controllers for some
reason were not affected by this problem.
Many Thanks to Tor Egge for bringing the aic7890 problem
to my attention, providing analysis, as well as a mechanism
to reproduce the problem.
is not desired, then the user can register an EV_SIGNAL filter to
explicitly catch a signal event.
Change requested by: jayanth, ps, peter
"Why is kevent non-restartable after a signal?"
stored at a different location in the PCI space, so adjust accordingly.
Also, when using more than two smart controllers in one machine, the
disks were assigned the wrong drive number; fix this as well.
This is in fact an Intel Orion chipset (82454KX/GX) which has been used
in HP NetServer's LS4 range.
HP Probably relabeled the DID. That's the only explanation I can find
plausible to this `mystery'.
doesn't exist. This could bite you by allowing you merrily install your
modules one on top of the other as the regular file ${DESTDIR}/modules
and think it completed properly...
operation or after it. If the ktrace operation was enabled while the
process was blocked doing IO, the race would allow it to pass down
invalid (uninitialized) data and panic later down the call stack.
the 12.4.11 firmware with a few changes to the link handling code merged
in from the 12.4.13 release. I'm doing this because the 12.4.13 firmware
doesn't seem to handle 10/100 link settings properly on 1000baseT cards.
Note that the revision codes still identify the firmware as 12.4.13
because both ti_fw2.h and ti_fw.h have to have the same revision values,
and I wanted to keep the 12.4.13 firmware for Tigon 1 cards.
It's nice to have firmware source.
certain uses of snapshots and currently appears to be causing some
other problems. So for now, I am reverting to the old semantics until
I have had time to investigate what is causing the other problems.
the SF_IMMUTABLE flag to prevent writing. Instead put in explicit
checking for the SF_SNAPSHOT flag in the appropriate places. With
this change, it is now possible to rename and link to snapshot files.
It is also possible to set or clear any of the owner, group, or
other read bits on the file, though none of the write or execute
bits can be set. There is also an explicit test to prevent the
setting or clearing of the SF_SNAPSHOT flag via chflags() or
fchflags(). Note also that the modify time cannot be changed as
it needs to accurately reflect the time that the snapshot was taken.
Submitted by: Robert Watson <rwatson@FreeBSD.org>
allow for that.
o Remember to call NDFREE() if exiting as a result of a failed
vn_start_write() when snapshotting.
Reviewed by: mckusick
Obtained from: TrustedBSD Project
names with a leading underscore. Notably, the 'stat' parameter in the
kld_stat() prototype conflicted with stat() and generated a BDE warning.
Approved by: peter
wrong bytes.
o Improve the public interface; use void* instead of char* or u_int64_t
to pass arbitrary data around.
Submitted by: kris ("horrible bug")
didn't bother to send a saved data pointers after the last transfer,
is not recorded in sgptr. This was only a problem if the target
reported non-zero status as we always check the residual in that case.
- It's worthwhile to use untimeout(9), even though we must still protect
against "false" timeouts, because most of the time it saves having to
handle a dummy timeout event.
- Slight tweaks to the delayed ACK algorithm paramters.
- Fix slowness when operating over fast connections, where the timeout(9)
granularity is on the same order of magnitude as the round trip time.
timeout(9) can happen up to 1 tick early, which was causing receive
ack timeouts to happen too early, causing bogus "lost" packets.
- Increase the local time counter to 64 bits to avoid roll-over.
- Keep statistics on memory allocation failures.
- Add a new option to always include the ack when sending data packets.
Might be useful in high packet loss situations. Might not.
Correct the BUILD_TCL macro. It was placing the target id
in the wrong bits. This was only an issue for adapters that
do not perform SCB paging (aha-3940AUW for instance).
Don't bother inlining ahc_index_busy_tcl. It is never
used in a performance critical path and is a bit chunky.
Correct ahc_index_busy_tcl to deal with "busy target tables"
embedded in the latter half of 64byte SCBs.
Don't initialize the busy target table to its empty state
until after we have finished extracting configuration
information from chip SRAM. In the common case of using
16 bytes of chip SRAM to do untagged target lookups,
we were trashing the last 8 targets configuration data.
(actually only target 8 because of the bug in the
BUILD_TCL macro).
Cram the "bus reset delivered" message back under bootverbose.
Fix the cleanup of the SCB busy target table when aborting
commands. If the lun is wildcarded, we must loop through
all possible luns.
aic7xxx.h:
Only bother supporting 64 luns right now. It doesn't seem
like either this driver or any peripherals will be doing
information unit transfers (where the lun number is a
32 bit integer) any time soon.
aic7xxx.seq:
Fix support for the aic7895. We must flush the data
FIFO if performing a manual transfer that is not
a multiple of 8 bytes. We were doing this quite
regularly for embedded cdbs.
Manaually flush the fifo on earlier adapters when
dealing with embedded cdbs too. We were stuffing
the FIFO with 16 bytes instead, but triggering
the flush is more efficient and allows us to
remove two instructions from the "copy_to_fifo"
routine.
pcic_attach() got a wrong pointer to pcic_slots since device haven't
set correct unit number yet, so always accessed elements of pcic_slots
which belong to pcic0 (unit number 0).
Now we set unit number to pcic device first, then access to pcic_slots
based on the unit number we've just set.
Add spl/splx to various sensitive spots
Change semantics of the vmnet version of the device to keep VMware happy
(don't junk state when the device is closed)
Submitted by: vsilyaev@mindspring.com
with the new snapshot code.
Update addaliasu to correctly implement the semantics of the old
checkalias function. When a device vnode first comes into existence,
check to see if an anonymous vnode for the same device was created
at boot time by bdevvp(). If so, adopt the bdevvp vnode rather than
creating a new vnode for the device. This corrects a problem which
caused the kernel to panic when taking a snapshot of the root
filesystem.
Change the calling convention of vn_write_suspend_wait() to be the
same as vn_start_write().
Split out softdep_flushworklist() from softdep_flushfiles() so that
it can be used to clear the work queue when suspending filesystem
operations.
Access to buffers becomes recursive so that snapshots can recursively
traverse their indirect blocks using ffs_copyonwrite() when checking
for the need for copy on write when flushing one of their own indirect
blocks. This eliminates a deadlock between the syncer daemon and a
process taking a snapshot.
Ensure that softdep_process_worklist() can never block because of a
snapshot being taken. This eliminates a problem with buffer starvation.
Cleanup change in ffs_sync() which did not synchronously wait when
MNT_WAIT was specified. The result was an unclean filesystem panic
when doing forcible unmount with heavy filesystem I/O in progress.
Return a zero'ed block when reading a block that was not in use at
the time that a snapshot was taken. Normally, these blocks should
never be read. However, the readahead code will occationally read
them which can cause unexpected behavior.
Clean up the debugging code that ensures that no blocks be written
on a filesystem while it is suspended. Snapshots must explicitly
label the blocks that they are writing during the suspension so that
they do not cause a `write on suspended filesystem' panic.
Reorganize ffs_copyonwrite() to eliminate a deadlock and also to
prevent a race condition that would permit the same block to be
copied twice. This change eliminates an unexpected soft updates
inconsistency in fsck caused by the double allocation.
Use bqrelse rather than brelse for buffers that will be needed
soon again by the snapshot code. This improves snapshot performance.
to construct a path that was long enough (ie longer than
SPARE_USRSPACE bytes) and trash the stack.
Note that SPARE_USRSPACE is much smaller than MAXPATHLEN so that
the Linuxulator will now return ENAMETOOLONG even if the path
is smaller than MAXPATHLEN.
PR: 12749
o Make the comments KNF-compliant.
o Use nanotime instead of getnanotime; the manpage lies about the
kern.timecounter.method - it has been removed.
o Fix the ENTROPYSOURCE const permanently.
o Make variable names more consistent.
o Make function prototypes more consistent.
Some more needs to be done; to follow.
Robert Watson
Sheldon Hearn
KATO Takenori
Jeroen Ruigrok van der Werven
Kazutaka YOKOTA
Justin T. Gibbs
Jonathan Lemon
Poul-Henning Kamp
Brian Feldman
Marcel Moolenaar
Bill Paul
Archie Cobbs
Kirk McKusick
John Baldwin
Nick Hibma
Nick Sayer
Mark Murray
Hajimu UMEMOTO
Bill Fumerola
Paul Saab
Mitsuru IWASAKI
Kenneth D. Merry
Seigo Tanimura